V-tech Go! Go! Smart Wheels 4-in-1 Zig-Zag Raceway User manual

Instruction Manual
4-in-1
Zig-Zag Raceway
™

2
SmartPoint®Stunt Car
Engine Button
Windshield Button
On/Off Switch
3 SmartPoint®
Locations
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®
4-in-1 Zig-Zag Raceway™track set.
Get racing with the Four different track configurations. Open up
a world of racing and stunt play. Choose from Battle Raceway,
Zig-Zag Track, Stunt Raceway and Super Ramp. Let’s go!

3
INCLUDED IN THE PACKAGE
IJ
E
K
A
G
B
H
One SmartPoint®
Stunt Car
F
C D

4
•Label Sheet
•Quick Start Guide
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy and should be discarded for your child’s safety.
NOTE
Please save this Instruction Manual as it contains important information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes, cordons et vis d’emballage. Ils ne font pas partie du jouet.
NOTE
Il est conseillé de sauvegarder ce manuel d’instructions car il comporte
des informations importantes.
Unlock the Packaging Locks
Pull out the packaging locks and discard.
Turn the packaging locks counterclockwise
several times.
INSTRUCTIONS
Battery Removal And Installation
Stunt Car
1. Make sure the unit is turned OFF.
2. Find the battery cover located on
the bottom of the Stunt Car. Use a
screwdriver to loosen the screw, and
then open the battery cover.
3. Remove old batteries by pulling up
on one end of each battery.

5
4. Install 2 new AAA (AM-4/LR03) batteries following the diagram
inside the battery box. (For best performance, alkaline
batteries or fully charged Ni-MH rechargeable batteries are
recommended).
5. Replace the battery cover and tighten the screw to secure.
IMPORTANT: BATTERY INFORMATION
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotmixoldandnewbatteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Onlybatteriesofthesameorequivalenttypeasrecommendedare
to be used.
• Donotshort-circuitthesupplyterminals.
• Removebatteriesduringlongperiodsofnon-use.
• Removeexhaustedbatteriesfromthetoy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinfire.
RECHARGEABLE BATTERIES:
• Removerechargeablebatteries(ifremovable)fromthetoybefore
charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Donotchargenon-rechargeablebatteries.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
ATTENTION :
Les piles ou accumulateurs doivent être installés par un adulte.
Tenir les piles ou accumulateurs hors de portée des enfants.

6
LABEL APPLICATION
Please stick the labels to the track set as shown below:
1 1 2
334
67
7
8
9
10
5
11
12
13 14

7
3
1
10
5
8
11 6
12
4
14
2
13
7 7
9

8
ASSEMBLY INSTRUCTIONS
Battle Raceway
1. Insert B into A as shown below. Make sure you hear a clicking
sound to confirm the pieces are firmly connected.
2. Insert C and D into A.
3. Insert E into B.
With the Go! Go! Smart Wheels 4-in-1 Zig-Zag Raceway™,
Adult assembly required. For your child’s safety, do not let them
play with this toy until it is fully assembled.

9
4. Snap F onto C and D as shown below, then insert F into E. Once
the above steps are completed, the main building is complete.
Please note that it cannot be disassembled.
5. Lay the assembled pieces down as shown.
6. Insert G and J into I, then connect to E.

10
7. Connect H to K, then connect K to B.
Once you’ve completed the above steps, the Battle Raceway is ready
to play.
Zig-Zag Track
1. Slide G into the second floor slot as shown below. Make sure
you hear a slight pop sound to confirm G has been connected
correctly.