Vanguard VGFRG-2124-2125BK User manual

2016-20 Toyota Tacoma
Elite Modular Front Runner
VGFRG-2124-2125BK
Installation Instruction
Thank you very much for choosing our products.
Please read the installation instruction carefully before using our product and be sure to
fully understand the contents mentioned above for subsequent installation.
In addition, please keep properly the installation instruction for product maintenance in
future.
Attention
The following symbols are used in this installation instruction.
Relevant matters must be obeyed for safety.
Non-compliance may result in injury or other accidents.
Please read carefully and obey strictly.
Relevant matters must be obeyed for the smooth installation
and use.
Non-compliance may cause the problems with vehicle. Please do not install that is not
recorded in this instruction.
Please forgive that we are not responsible for any consequences arising from the
installation not according to our installation instruction.


Product Composition *Please confirm if it is missing.
A
、
Side bend (2
pieces
，
R
、
L)
B
、
Top bend (1
pieces)
C
、
Middle tube
(1 piece)
D
、
Sand baffle plate
(1 piece)
E
、
Sub plate
（
2 pieces
，
R
、
L
）
F
、
Mount Bracket
（
2 pieces
，
R
、
L
）
G
、
Top Support
Bracket
（
2 pieces
，
R
、
L
）
H
、
M10*35
(55*18*T=5) -8.8
“
T
”
Bolt
（
2
pieces
）
I
、
M10*35-8.8 Bolt
（
14 pieces
）
J
、
M10
（Φ
10.5*
Φ
25*T2.0
）
Flat
Washer
（
24 pieces
）
K
、
M10 Lock
Washer
（
24
pieces
）
L
、
M10 -8.0 Nut
（
10
pieces
）
M
、
M8*20 -8.8 Bolt
（
4 pieces
）
N
、
M8
（Φ
8.4*
Φ
22*T1.5
）
Flat
Washer
（
4 pieces
）
O
、
M8 Lock Washer
（
4 pieces
）
P
、
M10
（Φ
48*
Φ
12*5.0
）
Flat
Washer
（
4 pieces
）
Q
、
M10*120 -8.8
Bolt
（
L=50
）（
2
pieces
）
R
、
M10 plastic
retainers
（
2 pieces
）
Installation tools *Please prepare these tools before installation.
Allen wrench #6 wrench 13/14 wrench 16/17

Attentions
- The labels of fitting procedure inside the thick wire frame is particularly important. Pay attention to them in the
actual installation.
- Pay attention to safety during installation.
Fitting Procedure
（
The installation process is shown below
，
Fig1-8
）

Fig1
：
Parts assembly
I、 J、 K
M、N、

Fig2
：
Parts assembly
Fig3
：
Open hood and remove plastic cover to locate cross-support in front of radiator
(arrows)
I
、
J
、

Fig4：Plastic bumper removed for instruction purposes only-do not remove bumper，Locate
the outer holes in the bottom of the radiator cross support (arrow) viewed from below.
Fig5：Insert Bolt plate (arrow) into back of radiator cross support and down through hole in
bottom (passenger side pictured through bumper）

Fig6：Driver side Bolt Plate installed

Fig6
：
Passenger side Top Support Bracket Fig7
：
Passenger side Top Support Bracket
installed-pictured from below bumper
Fig7
：
Installation Instruction
H、J、K、
J
、
K
、
L

Fig8
：
Installation complete
I、J、K、
Existing factory screw
K、L、P、

TIPS:
= Routine Maintenance =
1) Please use neutral detergent to wet the soft cloth or suede and so on, then clean our product.