Vaporesso LUXE X User manual

USER
MANUAL
VAPORESSO LUXE X

1English English 2
Thank you for choosing Vaporesso product. Please
read this instruction carefully before use to ensure
a perfect experience.
If there is any additional requirement about this
product, please consult the local agent or contact
us through our website: www.vaporesso.com
ENLARGED VIEW
Air-inlet Port
Type-C USB Port
ENGLISH
Drip Tip
3 x LED Light
Power Button
FIGURE 1
FIGURE 2
1
1
2
2
3
CLOSE
OPEN
ROTATE 180°

1English English 2
Thank you for choosing Vaporesso product. Please
read this instruction carefully before use to ensure
a perfect experience.
If there is any additional requirement about this
product, please consult the local agent or contact
us through our website: www.vaporesso.com
ENLARGED VIEW
Air-inlet Port
Type-C USB Port
ENGLISH
Drip Tip
3 x LED Light
Power Button
FIGURE 1
FIGURE 2
1
1
2
2
3
CLOSE
OPEN
ROTATE 180°

3English English 4
1. Replace the POD
- Take out the used POD from the battery;
- Install a new POD to the battery and make sure
they are firmly connected.
2. Fill the E-liquid(Refer to FIGURE 1)
- Take out the used POD from the battery and pull
out the silicone plug from the bottom of the POD;
- Fill e-liquid through the hole
- Put the silicone plug back in place firmly after
USER INSTRUCTIONS
Dimensions: 98 x 21.5 x 21.6 mm
POD Capacity: 5ml/2ml
Compatible POD:
LUXE X 0.4Ω MESH POD(32W)
LUXE X 0.8Ω MESH POD(16W)
Battery Capacity: 1500mAh
Output Power: 40W MAX
Charging Current: DC 5V/1.5A,Type-C
Display : 3 x LED Light
1 x VAPORESSO LUXE X Battery
1 x VAPORESSO LUXE X 0.4Ω MESH POD(5ml/2ml)
1 x VAPORESSO LUXE X 0.8Ω MESH POD(5ml/2ml)
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
SPECIFICATION
PACKING LIST
filling is finished.
- Please wait 5 minutes for the e-liquid to soak
into the coil completely.
3. Adjust the Airflow(Refer to FIGURE 2)
To adjust the airflow volume, try rotating the POD
180° and inserting it. There are two looser or tighter
airflow volume for selecting.
4. Power on the Device
Click the power button 5 times in 2 seconds to
power on or power off the device.
5. Start Vaping
Press the power button to enjoy extraordinary
vaping experience.
6. Battery Level
7. Charge the Battery
After connecting the Type-C cable to the battery,
the battery indicator and remaining charging
time will be showed on the screen.
8. Safety Mode
If the vaping time over 8 seconds, the power level
LED light breathing 3 times and the device will be
powered off automatically, press power button 5
times constantly to power on again.
LED Battery Status
60%-100%
30-60%
≤30%

3English English 4
1. Replace the POD
- Take out the used POD from the battery;
- Install a new POD to the battery and make sure
they are firmly connected.
2. Fill the E-liquid(Refer to FIGURE 1)
- Take out the used POD from the battery and pull
out the silicone plug from the bottom of the POD;
- Fill e-liquid through the hole
- Put the silicone plug back in place firmly after
USER INSTRUCTIONS
Dimensions: 98 x 21.5 x 21.6 mm
POD Capacity: 5ml/2ml
Compatible POD:
LUXE X 0.4Ω MESH POD(32W)
LUXE X 0.8Ω MESH POD(16W)
Battery Capacity: 1500mAh
Output Power: 40W MAX
Charging Current: DC 5V/1.5A,Type-C
Display : 3 x LED Light
1 x VAPORESSO LUXE X Battery
1 x VAPORESSO LUXE X 0.4Ω MESH POD(5ml/2ml)
1 x VAPORESSO LUXE X 0.8Ω MESH POD(5ml/2ml)
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
SPECIFICATION
PACKING LIST
filling is finished.
- Please wait 5 minutes for the e-liquid to soak
into the coil completely.
3. Adjust the Airflow(Refer to FIGURE 2)
To adjust the airflow volume, try rotating the POD
180° and inserting it. There are two looser or tighter
airflow volume for selecting.
4. Power on the Device
Click the power button 5 times in 2 seconds to
power on or power off the device.
5. Start Vaping
Press the power button to enjoy extraordinary
vaping experience.
6. Battery Level
7. Charge the Battery
After connecting the Type-C cable to the battery,
the battery indicator and remaining charging
time will be showed on the screen.
8. Safety Mode
If the vaping time over 8 seconds, the power level
LED light breathing 3 times and the device will be
powered off automatically, press power button 5
times constantly to power on again.
LED Battery Status
60%-100%
30-60%
≤30%