Varimixer V80 Guide

SPARE PART AND OPERATION MANUAL
FOOD MIXER
Model V80, V80PL, V100PL
121520

2
Caution -READ BEFORE OPERATING- Caution
Varimixer recommends that mixer operators must be at least 18 years of age and be thoroughly
trained on the use, cleaning and lubrication of the mixer.
This manual should be seen as an integral part of the mixer and should be kept by the machine
throughout its working life.
Before the machine is commissioned, it is important to read these instructions thoroughly.
The manufacturer may update the product manual without updating this copy of the manual.
Varimixer recommends that the following precautions be adopted to help make the mixer operation
safer and more efficient.
- All operators must be at least 18 years of age.
- All operators must be thoroughly trained before being allowed to operate the mixer.
- NEVER reach into the bowl when the mixer is running.
- Do not wear loose clothing or rings while operating the mixer.
- Stop the mixer and lower the bowl before adding ingredients, scraping the bowl, removing
the agitator, or removing the product.
- Stop the mixer before removing or installing attachments into the drive hub.
- Do not attempt to assemble or disassemble attachments while mounted into the drive hub.
- Always use the pusher plate with the slicer/meat grinder attachments.
- NEVER bypass the safety mechanisms supplied on the mixer. Doing so can cause injury
and.is the responsibility of the user to ensure these safety mechanisms are operating
properly.

3
Limited Mixer Warranty
VARIMIXER warrants to the original purchaser of new equipment that said equipment, when installed in accordance
with our instructions within North America and subjected to normal use, is free from defects in material or workmans-
hip for a period of 2 years. Wear parts, such as belts, are excluded. Hub attachments, such as shredders, slicers and
grinders have a 1 year warranty that only covers parts. Warranty begins on date of factory shipment to an end user, or
up to 6 months after factory shipment to a dealer or distributor. Payment by VARIMIXER for service under this warranty
requires that service be authorized in advance. Contact VARIMIXER Technical Support to arrange for service.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. VARIMIXER
EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
VARIMIXER’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING
AND REPLACING EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN
THE APPLICABLE WARRANTY PERIOD. All repairs pursuant to this Warranty will be performed by an Authorized
Designated VARIMIXER Service Location during normal working hours. IN NO EVENT SHALL VARIMIXER BE LIA-
BLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING, WIT-
HOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER
ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY,
STRICT LIABILITY, OR OTHERWISE.
This warranty is given only to the rst purchaser from a retail dealer. No warranty is given to subsequent transferees.
This warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess
water, re, normal wear, improper set up and use. Periodic maintenance is not covered.
Example of items not covered under warranty, but not limited to just these items:
1. Acts of God, re, water damage, vandalism, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after market parts.
5. Repairs made by anyone other than a VARIMIXER designated servicer.
6. Lubrication.
7. Expendable wear parts. (This includes the bowl, at beater, wire whip, spiral dough hook,
and the pastry knife.)
8. Cleaning of equipment.
9. Misuse or abuse.
This warranty is not in force until such time as a properly completed, digitally signed Installation/Warranty Registration
has been received by VARIMIXER within 30 days from the date of installation.
Register online at www.varimixerusa.com/support/warranty-registration-form.
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE
BUYER AND SELLER. VARIMIXER NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT
ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.
WARRANTY REGISTRATION
GO TO WWW.VARIMIXERUSA.COM
TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.
WWW.VARIMIXERUSA.COM/SUPPORT/WARRANTY-REGISTRATION-FORM

4
 .............................................................................................................. 5
 ................................................................................................................. 6
 ........................................................................................................ 6
........................................................................... 7
 ................................................................................................................................ 7
 .............................................................................................. 7
.......................................................................................................................................... 7
 .................................................................................................................................... 7
.................................................................................................................... 7
........................................................................................................................................... 7
........................................................................................................... 8
................................................................................................................................. 8
 ...................................................................................................... 9
 ................................................................................................................................... 9
.................................................................................................... 9
 .............................................................. 9
 ..................................................................................... 10
  ........................................................................................ 10
 ....................................................................................................... 10
 ..................................................................................... 11
  ............................................................................................ 11
  ........................................................................................... 11

 ........................................................................................................... 13
 ........................................................................................... 15
 ....................................................................................................... 17
 .......................................................................................................... 19
............................................................................................................. 21
 ................................................................................................................. 23
 ..................................................................................................... 25
....................................................................................... 27
.................................................................................................................. 29
............................................................................................. 31
................................................................................... 33
 ...................................................................... 35
........................................................................................ 37
............................................................. 38
............................................................. 39


5
Read this page entirely BEFORE beginning installation.
INSTALLATION INSTRUCTIONS
UNDER NO CIRCUMSTANCES ARE THE SPEED LEVER, BOWL LIFT LEVER, OR THE BOWL
ARMS TO BE USED TO MOVE THE MIXER INTO PLACE. DAMAGE WILL RESULT TO THE UNIT.
IT IS RECOMMENDED THAT THE TOP LID BE REMOVED BEFORE MOVING THE UNIT.
The mixer must be mounted with the rubber feet, which neutralize both shaking and rusting.
Spacers can be inserted under the mixer’s feet if the floor is uneven. The mixer can be bolted to the
floor if desired.
Before the mixer is connected to power, it should be checked that the voltage and frequency on the
rating plate is correct in relation to the place of installation. A unit labeled 220V 3 Phase will operate
from 208V to 240V 3 phase safely. The rating plate is located on the rear right side of the mixer. The
electrical connection box is located at the top rear of the mixer.
WARNING
Electrical and grounding connections must comply with applicable portions of the National Electrical
Code and/or other local electrical codes................................................................ire
Wire Color Codes
White-Phase 1
Red -Phase 2
Black-Phase 3
Green-Ground
No Neutral is used
1. Lower the bowl using the bowl lift lever or pres
the button for bowl lift on the front panel.
4. Close bowl screen and raise
the bowl arms into the up
position.
5. Set timer to 10 minutes and
push “start” .
6. Insure cover is rotating in
the correct direction.
2. Open the bowl screen. 3. Remove the bowl
and tools.

6
Emergency stop
Fig. 3
Mixer seen from above,
the bowl has been pushed
all the way into the bowl
arms.


Fig. 2
Speed selector and
manual 
First “ear”
Second “ear”
Centre
“ear”
Fig. 1 Operation panel.
Timer/
Display
Start/Stop
Time up
Time

Speed selector lever

speed

speed

speed must be selected.
Pause







 Place the tool in the bowl. Open the bowl screen
 . Place
the bowl in the bowl arms. Check that the bowl is pushed right
back into the arms and that the “centre ear” of the bowl arms
is facing the mixer . Place the mixer tool in the bayonet
shaft. The tap of the tool must be turned right into the bayo-
net hole. Close the bowl screen.
 Raise the bowl to working position by turning the handle for
bowl lift towards your selves (manual bowl lift) or by
pressing (Power lift). The bowl will automatically
stop in the top position.
 The mixing time can be set on the timer using the and
buttons. The mixer stops automatically when the mixing
time has run out. (If the mixer stops at high speed when the
mixing time runs out, follow the instructions 
 before starting the mixer again).
You can also start the mixer without setting a time. If you do
not set a time, the display will function as a clock that counts
up. See also “Timer function” on page 7
 Start the mixer by pressing 
 Turn the speed selector lever  to the rear until the
required speed has been obtained, (notice the recommended
maximum speeds on page 9).
The speed must be changed only when the mixer
is running.
The mixer must not be started in high speed
when loaded.
Always change to low speed before stopping the
mixer
 
During the mixing process the mixer can be paused by pressing
(). You can now lower the bowl
or open the bowl screen. If you start the mixer again using
the timer settings will be unchanged.
 Before the mixer is stopped, the speed selector lever must
be moved back to lowest speed . Stop the mixer by
pressing 
 When the tool has stopped rotating the bowl can be lowered
by pressing (power lift) or by turning lever for bowl lift to
the rear.

The mixer has a pause button , which should be used to stop
and start the mixer in a process where the timer is used.
• Change to low speed
• Stop the mixer using . The timer will continue to count
downwards when you start the mixer again by pressing .
• When you stop the mixer pressing you can lower the
bowl and open the bowl screen. When you press again,
the timer continues to count downwards.
• If you start the mixer using the settings will be reset. See
also “Pause function”
Lever for
manual


7

Whips should not be struck against hard objects as
e.g. the edge of the bowl. This will make the life of the tool
shorter due to increasing deformity.

For production of mashed potatoes the special wing
whip or the whip with thicker wires should be used, alterna-
tively use the beater and the whip.
NOTE: Speed should never exceed 150 RPM when using
the dough hook. Our dough hook is designed to give you
optimum product on low speed.

The mixer should be unplugged before cleaning to pre-
vent accidental starting while cleaning.
The mixer should be cleaned daily or after use.
The mixer should be cleaned with a soft cloth and clean wa-
ter. Sulphonated soaps should be used with caution as they
destroy the mixer’s lubricants.
Never use high pressure cleaning for the mixer.
Parts made of aluminum should not be used
to strongly acidic, highly alkaline or highly salty
foodstus, which may attack aluminum without
coating.
Tools of aluminium must not be washed with
strong alkaline detergents (pH between 5 and 8).
The soap suppliers can recommend the correct type of soap.
The inside of the beater shaft should be cleaned once a day
with warm, soapy water.
Dough hook Cleaning: Special care should be given to
cleaning the dough hook. We recommend that it be cleaned
and sanitized in a commercial dish machine. An alternate
cleaning procedure is to vigorously scrub the hook with a
hot.water and detergent solution. Use a heavy bristled
brush. After cleaning, sanitize the hook by rinsing it with a
50 ppm solution of sodium hypochlorite.
 after use of the attachment
hub this should be wiped inside with a soft cloth.
 Beater 
Cream Cake dough Bread dough
Egg whites Butter cream Dark bread
Mayonnaise Wa󰀪e dough and the like
and the like Minced meat
and the like

If the timer is in use, the bowl can automatically be lowered
when the time runs out and the mixer stops.
• While the mixer is running, briey press , The green
LED by will ash until the mixer stops.
• When automatic lowering of the bowl is selected it is
important that you use ()
to stop and start the mixer, otherwise the selection will be
reset.

The mixer has an optional timer function. If no time is set on
the timer, the display will instead show the time the mixer has
run for.
• The timer can be set to a maximum of 60 minutes.
• and can be used to set the time before starting
the mixer or while the mixer is running. The time can be
changed after it has been set.
• 
selected speed.

This procedure is used in all cases where the mixer has been inter-
rupted at high speed, either because the mixer has been stopped
using or , the mixing time has run out, the emergency stop
is activated or the bowl screen is opened:
 Lower the bowl and remove the tool from the bayonet.
 Raise the bowl arms, either empty or with the bowl.
 Close the bowl screen, start the mixer and move the
speed selector lever back to lowest speed.
 Switch o󰀨 the mixer. Now the mixer can be started as usual.

Do not overload the mixer. Sticky and heavy doughs
can overload the mixer. Overloading is further exac-
erbated if the speed of the mixing tool is increased
beyond the recommended values or if a wrong mix-
ing tool is used. Large lumps of fat or cooled ingre-
dients must be cut into small parts before they are
placed in the bowl.
Longer time overload will interrupt the mixer.
will be written in the mixer’s display. After
a short while the display will change back to normal
mode and you can start the mixer again as de-
scribed in “Start-up after stop at high speed”.

If the mixer is overloaded, the motor will stop and will
be shown for ‘overheat’ in the display.
• Allow the mixer to cool down.
• After a short time, the display will change to normal
mode.
• The mixer can be started again. See also the section
.

8
Motor

Speed
adjustment
Motor relay /

load relay


Fuse







upper position of




Product V80 V100
Dough, Bread-65%AR 105 Lbs. 155 Lbs.
Dough, Pizza-50% AR 90 Lbs. 135 Lbs.
Dough, Donut-Yeast 80 Lbs. 150 Lbs.
Dough, Donut-Cake 60 Lbs. 140 Lbs.
Pie Dough 69 Lbs. 95 Lbs.
Cookie, Dough 68 Lbs. 105 Lbs.
Mu󰀩ns 90 Lbs. 125 Lbs.
Mashed Potatoes 58 Lbs. 76 Lbs.
Pancakes, Wa󰀪es 35 Qts. 44 Qts.
Whipped Cream 16 Qts. 20 Qts.
Cake, Layer 92 Lbs. 125 Lbs.
Eggs & Sugar 40 Lbs. 57 Lbs.
Icing , Fondant 50 Lbs. 76 Lbs.
Egg Whites 2.5 Qts 3 Qts.
Cake, Cup 140 dz. 178 dz.
Cookies, Sugar 132 dz 171 dz.


(Liquid in % of solids)

1 Gallon =8.33 lbs.
1 Quart =2.08 lbs.
1 Pint (16 oz.) =1.04 lbs.
1 Cup = .52 lbs.
Batch size and/or speed reduction may be necessary due to one
of the following conditions:
1.High Gluten Flour-Reduce batch size by 10%
2.AR % under 40%-Reduce batch size by 10%
3.Water temp under 65 Degrees F
4.USE OF ICE REQUIRES A 10% REDUCTION IN BATCH
SIZE.
5. Speed should not exceed 100 RPM when mixing dough.
V80 V100
4 HP 4 HP

9



The innitely variable gear must be lubricated regularly, i.e. a lubri-
cation interval of approx. 60 hours of operation.

OBS. Special grease !!(Use the grease gun delivered together with
the mixer). Start the mixer and increase the speed to approx. 50%.
Stop the mixer (use the emergency stop) and open the lid on the
top of the mixer. On the top of each of the two pulley set shafts is
a grease nipple . Press grease through the grease
nipples.
until the grease gun feels hard to press or until grease comes out
between the shaft and the pulleys.
The mixer must not be started until the screws which
hold the lid are inserted.
Start the mixer, and set the speed back to low speed.
Stop the mixer and ll the grease gun with new grease so that it is
ready for next time.

The movable parts of the bowl arms, the shaft and the lifting rod
must also be lubricated with oil. Remove the rear covering and
lubricate the marked points with an oil can. 

Grease for the pulley set shafts:
Grease.
On repair of the planetary head: Grease the toothed wheel and
the toothed rim with ,the needle
bearings in the planetary head must not be lubricated with this type
of grease they should be lubricated with .Do
not use any another type of grease than the one stated here.
On repair of the attachment hub: Fill the attachment hub
with GreaseWay LiCa 80
1 2 3 4 5
MIN MAX



10


 
A rattling sound from the closed part of the mixer. Adjustment of special v-belt
The mixer starts “striking” when kneading dough Adjustment of special v-belt
which normally causes no problems.
The mixer changes its speed by itself. Adjustment of special v-belt
The minimum and the maximum speeds are changing. Adjustment of speed.
The bowl is too tight or too loose. Adjustment of bowl xing
The tool hits the sides of the bowl. Adjustment of bowl centering
The tool hits the bottom of the bowl. Adjustment of bowl height
󰀨

The distance  is only indicative as it depends on the
tolerance of the special V-belt.
1. Start by tightening the v-belts *
2. Tighten the special V-belt  by moving one or two wash-
ers from  to .
3. Start the mixer and leave it running while the nut  is
tightened. Do not tighten it too much.
4. On the front pulley set the stud  on the varispeed collar
 must be placed inside the lower fork  and on the
rear pulley set outside the fork for belt tightener , (both
must point backwards).
5. Tolerances in the transmission might cause that the spe-
cial V-belt  is hitting the pins of the pulley sets when
the speed has been adjusted. In such cases the distance
 must be reduced. (+ or - 1/8" of 12 1/4")
6. Then follow the section:
“Adjustment of speed”

1. The stop screws  on the speed lever should be
adjusted so that the measurement  is  on the
front and the rear pulley, at low and high speed, respec-
tively. Tighten the counter nuts  when the speed is
correctly adjusted.
2. Tolerances in the transmission might cause that the
special V-belt  is hitting the pins of the pulley sets 
when the speed has been adjusted In such cases the dis-
tance  must be reduced, see “Adjustment of special
, and the speed must be readjusted.

11

 
 
 
A
First nd the present bowl centering: mount the beater and the
bowl, then raise the bowl arms up to normal working position.
With your hand turn the beater, and then measure the distance
between beater and bowl edge. By removing the rear covering,
the bowl arm guide plate is now accessible . Loosen the
screws  and move the bowl arm guide plate in the required
direction. Again turn the beater and measure the distance
between beater and bowl. When the bowl has been centred,
fasten the bowl arm guide plate in the new position and screw
on the rear covering.

The bowl arms must be raised to normal working position. The
adjusting diameter  shall be measured inside between the
bowl arms :
Adjusting diameter     
   
In case the bowl fastening is too loose, remove the lock ring
 and draw the bearing  from the shaft . The bearing
should be turned 180oand be mounted on the shaft again.
It might be necessary to turn both bearings. At last check the
bowl centering and if necessary, adjust.

The distance  is measured from the bottom side of the
bayonet hole to the surface on the bowl arms on which the bowl
rests  The bowl arms must be lifted to normal working
position.
   
V100 = 11 3/4"
The upper and lower position of the bowl is determined by micro
switch and , . The two mechanical stops consist-
ing of the bolts and are adjusted so that they will be hit
approx. 1 mm after the micro switch, in case the micro switch
should fail.
The lower position is adjusted first; by sliding the en-
tire bracket assembly up or down on the slots on the
bracket (2). The upper position of the bowl arms is ad-
justed by adjusting the up position micro switch mount-
ing bracket (2) up or down; it is of utmost importance
that the stop screw (3) is re-adjusted afterwards.








12
20
22
21
1
2
3
4
5
6
7
7
8
9
10
11
23
19
27
25 26
18
14
17
16
15
13
12
24
28
29
30

13
Top Lid..............................................................AR81-21 ..................................................AR101-21
Screw for Lid M6x20.........................................STA 5017.................................................STA 5017
Threaded Bushing ............................................STA 6580.................................................STA 6580
Ground Screw...................................................STA 5232.................................................STA 5232
Arrow Label ......................................................R15-245...................................................R15-245
Plug Button.......................................................STA 6525.................................................STA 6525
Bushings for Bowl Arm Shaft............................STA 2526.................................................STA 2526
Knee Pad..........................................................AR80-212 ................................................AR80-212
Foot ..................................................................AR80-213 ................................................AR80-213
3MM Foot .........................................................AR80-214.3 .............................................AR80-214.3
6MM Foot .........................................................AR80-214.6 .............................................AR80-214.6
Screw M6X10 ...................................................STA 5080.................................................STA 5080
Rear Panel........................................................AR81-22.17R...........................................AR101-22.17R
Upper NSF Plate ..............................................AR81-270 ................................................AR81-270
Lock Nut ...........................................................STA 5834.................................................STA 5834
Washer .............................................................STA 6027.................................................STA 6027
Lower NSF Plate ..............................................AR81-271 ................................................AR81-271
Plug Button f/ No Hub.......................................STA 6510.................................................N/A
Machine Column...............................................AR81-22M0 .............................................AR101-22M0
Motor mount .....................................................AR81-148.1 .............................................AR81-148.1
Bolt ...................................................................STA 5686.................................................STA 5686
Washer .............................................................STA 6056.................................................STA 6056
Bushings for Bowl Lift Lever.............................STA 2515.................................................N/A
Bowl Arm Guide Plade......................................AR81-71 ..................................................AR81-71
Screw................................................................STA 5322.................................................STA 5322
spring washer ...................................................STA 6056.................................................STA 6056
Washer .............................................................STA 6020.................................................STA 6020
Nut....................................................................STA 5810.................................................STA 5810
Threaded Bush.................................................R20-148...................................................R20-148
Nut....................................................................STA5815..................................................STA 5815
Fig.No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.

Description V80 V100

14
3
2
4
5
6
7
1
8
11
12
13
9
7
9
10
16
15
14
W60-53.3M
WR81-612M

15
Fig.No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.

 
Screw.................................................................... STA 56277
Microswitch Bracket.............................................. AR81-612
Microswitch Cable ................................................ AR81-194.11
Cable Inlet ............................................................ STA 3002
Microswitch........................................................... WR81-194.11
Screw.................................................................... STA 5619
Microswitch........................................................... AR81-173
Microswitch Bracket.............................................. AR61-53.1
Microswitch Plate.................................................. AR61-53.3
Threaded Plate..................................................... AR31-712
Nut........................................................................ STA 5819
Washer ................................................................. STA 6053
Screw.................................................................... STA 5619
Washer ................................................................. STA 6085
Nut........................................................................ STA 5816
Screw.................................................................... STA 5274
.......................................... 
.............................................. 

16
81-600M

17
Lift Nut ..............................................................................................................................................R15-65
Crank Arm.........................................................................................................................................R60-63Z
Bowl Arm Shaft.................................................................................................................................R81-68Z
Lifting Rod ........................................................................................................................................R81-83Z
Lift Spring .........................................................................................................................................R60-110
Key ...................................................................................................................................................STA 2020
Snap Ring.........................................................................................................................................STA 3408
Snap Ring.........................................................................................................................................STA 3462
Screw................................................................................................................................................STA 5088
Nut....................................................................................................................................................STA 5827
Pin ....................................................................................................................................................STA 6205
Pin ....................................................................................................................................................STA 6370
Roller ................................................................................................................................................AR31-128
Lift Lever...........................................................................................................................................R100-62Z
Ball....................................................................................................................................................STA 3308
Shaft .................................................................................................................................................AR81-71.10
Roller ................................................................................................................................................AR81-71.5M
Bowl Lift Dampener ..........................................................................................................................W60-604
Bowl Lift Dampener, assy .................................................................................................................AR81-600.1M
Cotter Pin..........................................................................................................................................AR81-606
Pin For Lift/Dampener ......................................................................................................................AR81-67.1
Upper Mounting Bracket F/Dampener .............................................................................................AR81-609.1
Cotter Pin..........................................................................................................................................STA 6205
Bowl Arm Set....................................................................................................................................AR81-23/24Z
Bushings for Bowl Arms....................................................................................................................STA 2526
Eye Bolt for Bowl Arm Spring ...........................................................................................................STA 5550
Roller Shaft.......................................................................................................................................AR31-127
Nut....................................................................................................................................................STA 5819
Washer .............................................................................................................................................STA 6044
Fig.No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.

Description V80

18
1
19, 19A
3
2
5
3
18, 18A
17
7
10
14
12
11
13
9
16
15, 15A
20
16
4
AR81-23/24Z
AR101-23/24Z
86, 6A

19
Washer .................................................................... STA 6056
Bowl Lift Motor......................................................... AR30-86.2B
Pin ........................................................................... STA 6205
Lifting Rod ............................................................... RN100-67
Guide....................................................................... RN100-66
Bowl Arm Set for V80 .............................................. AR81-23/24M2
Bowl Arm Set for V100 ............................................ AR101-23/24M2
Roller Shaft.............................................................. AR31-127
Bushings for Bowl Arms........................................... STA 2526
Roller ....................................................................... AR81-71.5M
Shaft ........................................................................ AR81-71.10
Roller ....................................................................... AR31-128
Snap Ring................................................................ STA 3407
Screw....................................................................... STA 5088
Pin ........................................................................... STA 6370
Bowl Arm Shaft for V80 ........................................... AR81-68Z
Bowl Arm Shaft for V100 ......................................... AR101-68Z
Snap Ring................................................................ STA 3462
Screw....................................................................... STA 5322
Washer for V80........................................................ STA 6020
Washer vor V100..................................................... STA 6034
Fitting for Bowl Lift Motor for V80 ............................ AR81-86.40M4
Fitting for Bowl Lift Motor for V100 .......................... AR101-86.40
Pin ........................................................................... AR81-86.41
Fig.No
1.
2.
3.
4.
5.
6.
6A.
7.
8.
9.
10.
11.
12.
13.
14.
15.
15A.
16.
17.
18.
18A.
19.
19A.
20.

 

20
2
3
5
6
7
8
4
9
11
12
18
19
20
21
36
37
32
30
29
24
23
22
40
34
41
43
25
26
27
28
31
33
10
38
13
14
15
16
39
42
17
35
7
6
34
15
AR80-2.2M0
R100-30Z R100-3Z R100-2Z R100-2.1Z R100-3.6Z R100-101Z
1, 1A
V80 3 belts total
V100 4 belts total