Varimixer KODIAK V20KT Guide

DRN: 20020-1636
2022 01 12
Varimixer USA
2215 East River Road
Moraine, Ohio 45439
P: [phone]
varimixerusa.com
EN
KODIAK
_
Operating Instructions
And Spareparts
V20K KODI A K
Valid from machine number:
20019000

Limited Mixer Warranty - 10 qt to 150 qt
VARIMIXER warrants to the original purchaser of new equipment that said equipment, when installed in accordance
with our instructions within North America and subjected to normal use, is free from defects in material or workmanship
for a period of 4 years. Wear parts, such as belts, are excluded. Hub attachments, such as shredders, slicers and
grinders have a 1 year warranty that only covers parts. Warranty begins on date of factory shipment to an end user, or
up to 6 months after factory shipment to a dealer or distributor. Payment by VARIMIXER for service under this warranty
requires that service be authorized in advance. Contact VARIMIXER Technical Support to arrange for service.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. VARIMIXER
EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
VARIMIXER’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING
AND REPLACING EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN
THE APPLICABLE WARRANTY PERIOD. All repairs pursuant to this Warranty will be performed by an Authorized
Designated VARIMIXER Service Location during normal working hours. IN NO EVENT SHALL VARIMIXER BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING,
WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER
ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY,
STRICT LIABILITY, OR OTHERWISE.
This warranty is given only to the rst purchaser from a retail dealer. No warranty is given to subsequent transferees.
This warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess
water, re, normal wear, improper set up and use. Periodic maintenance is not covered.
Example of items not covered under warranty, but not limited to just these items:
1. Acts of God, re, water damage, vandalism, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after market parts.
5. Repairs made by anyone other than a VARIMIXER designated servicer.
6. Lubrication.
7. Expendable wear parts. (This includes the bowl, at beater, wire whip, spiral dough hook,
and the pastry knife.)
8. Cleaning of equipment.
9. Misuse or abuse.
This warranty is not in force until such time as a properly completed, digitally signed Installation/Warranty Registration
has been received by VARIMIXER within 30 days from the date of installation.
Register online at www.varimixerusa.com/support/warranty-registration-form.
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE
BUYER AND SELLER. VARIMIXER NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT
ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.
WARRANTY REGISTRATION
GO TO VARIMIXERUSA.COM
TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.
VARIMIXERUSA.COM/SUPPORT/WARRANTY-REGISTRATION-FORM

Caution -READ BEFORE OPERATING- Caution
Varimixer recommends that mixer operators must be at least 18 years of age and be thoroughly
trained on the use, cleaning and lubrication of the mixer.
This manual should be seen as an integral part of the mixer and should be kept by the machine
throughout its working life.
Before the machine is commissioned, it is important to read these instructions thoroughly.
The manufacturer may update the product manual without updating this copy of the manual.
Varimixer recommends that the following precautions be adopted to help make the mixer operation
safer and more efficient.
- All operators must be at least 18 years of age.
- All operators must be thoroughly trained before being allowed to operate the mixer.
- NEVER reach into the bowl when the mixer is running.
- Do not wear loose clothing or rings while operating the mixer.
- Stop the mixer and lower the bowl before adding ingredients, scraping the bowl, removing the
agitator, or removing the product.
- Stop the mixer before removing or installing attachments into the drive hub.
- Do not attempt to assemble or disassemble attachments while mounted into the drive hub.
- Always use the pusher plate with the slicer/meat grinder attachments.
- NEVER bypass the safety mechanisms supplied on the mixer. Doing so can cause injury and
is the responsibility of the user to ensure these safety mechanisms are operating properly.

4

............................................................................................................................................................................. 4
 ......................................................................................................................................................................... 4
......................................................................................................................................................................... 5
......................................................................................................................... 5
................................................................................................................................................... 6
 ................................................................................................................................................................. 6
.............................................................................................................................................................. 6
 ........................................................................................................................................................................... 7
 ............................................................................................................................... 7
................................................................................................................................................................................ 7
...................................................................................................................................... 8
 ....................................................................................................................................... 8
 ......................................................................................................................................................................... 8
............................................................................................................................................................................. 8
.......................................................................................................................................... 9
........................................................................................................................................... 10
 ......................................................................................................................................................11
 ........................................................................................... 12
 ............................................................ 12
................................................................................................................................................... 12
.......................................................................................................................................................................... 12
 .................................................................................................................................... 12
 .......................................................................................................................................................... 12
 .............................................................................................................................................. 13
.......................................................................................................................................... 13
................................................................................................................................................. 13
........................................................................................................................ 14
 .......................................................................................................................................................... 16
 ............................................................................................................................................................. 31

This manual should be seen as an integral part of the mixer and should be kept by the machine throughout its working life.
Before the machine is commissioned, it is important to read these instructions thoroughly, particularly the section on user safety.
The manufacturer may update the product manual without updating this copy of the manual.
The manufacturer will not be liable for faults caused by:
• Careless, improper or incorrect use of the mixer
• Nonstandard use (not for the purposes described in the manual)
• Incorrect installation
• Incorrect power supply to the machine
• Failure to comply with maintenance instructions
• Modications to the machine
• Spare parts and accessories that are not original or specied for this model
• Failure to comply with instructions in this manual
In case of faults with the mixer, please contact the Local Authorized Service Agency.
The guarantee does not cover damage caused by misuse, overloading or the user’s failure to comply with the maintenance
instructions.

The machine should be unpacked and the packaging disposed of according to regulations applicable in the country concerned.
Before the mixer is removed from the pallet, check that all parts are present with the machine:
• Safety guard and lling chute
• Power cable
• 32 mm xed spanner for legs.
• Bowl trolley for oor model
• Bowl, whip, beater, hook and scraper with blade, if these were selected with the order.
The machine can be released from the pallet by cutting the strips.

5
12
317/64”

Lifting equipment should always be used to move the machine.
The machine must not be pulled or lifted by the bowl lift handle.
When the machine is moved, it should be in a vertical position at all times.

The ambient temperature around the machine must not exceed 113oF.

 so that the bowl on the bowl trolley
ts perfectly into the bowl arms.
The bowl arms should be at the correct height above the oor before the machine
is taken into use – see “



The top of the mixer must be parallel to the oor. To ensure this you must measure the distance from the top of the machine
to the oor:
The dimension must be the same when measured at the front of the mixer and at the rear of the mixer:

The mixer must be height adjusted so that the bowl on the bowl trolley ts exactly in the bowl arms:
Basically, the dimension from oor to center of the knobs on the bowl arms must be 31 7/64”. If the bowl on the bowl trolley
does not t exactly in the bowl arms at this dimension, adjust slightly on the front legs of the mixer.


Kodiak 20 table model is xed with bolts in the two hind legs .
Bolts with dimensions M10 x 20 mm + table top thickness and a
washer are used.
The table must be suitable for machine’s weight and operation.

If the table is not fully even, justications can be made by adjusting
the two front legs.
The adjustment is made as described for the oor model - see above.
To raise leg





Together with the mixer comes a 32 mm
xed spanner to be used for adjustments.

6
18 35/64”
10 15/16”
30 5/16”
22 51/64”
24 49/64”
36 21/32”
50
55/64”
16 31/32”
21 7/32”22 7/8”
19”
22 29/32”
19 9/64”
8 5/32”
11 9/64”
17 13/32”
17 11/64”
31”
27 7/8”
7 1/4”

   hp   
   hp V A 
 407 363 1.6 115 10.3 64 - 353
 200 176






User




The cable is xed to the machine in the plug made of
silicone, see “Components of the machine” page 9
The machine is protected by a 10A fuse built into the socket
on the back of the machine.







When the machine is connected, 
or  should be used. In both cases,
it is important to ensure that the voltage between the two
live pins matches the name plate.


.
The name plate is positioned uppermost on the back of the machine.
.
If there is no ground connection, the EMC lter will not work, with the
risk of damage to the frequency converter.
NOTE


RCD


7

Bowl, tools, safety guard and lling chute should be cleaned before use – see section on “
 The bowl arms  be at the correct height above the oor before the machine is taken into use – see “
 page 5.
The machine  be xed to the table, see 

The machine is designed for the manufacture of products that do not trigger any reactions or release substances
that may be harmful to the user when in use.
The machine must not be used in an explosive atmosphere.
The machine must only be operated by sta󰀨 who have been trained in the use of the machine according to
these instructions. Users must be over 18 years of age.
The machine is designed for commercial use in kitchens, catering outlets and bakeries.
The machine may only be used as specied in this manual.
Only bowls designed for Kodiak 20 may be used.
Tools should be used in conjunction with the corresponding bowl – a 20 Q tool with the 20 Q bowl and a 20/12 Q tool with the
20/12 Q bowl.
Unless the change is recommended by the manufacturer, modifying the machine is prohibited.
If the machine is tted with an attachment drive, only accessories produced or recommended by manufacturer should be attached.

The machine is designed for the manufacture of products that do not trigger any reactions or release substances
that may be harmful to the user when in use.
Users must be over 18 years of age and trained in the use of the machine according to these instructions.

• Tools can only rotate when the safety guard is in place and the bowl is lifted.
• The safety guard is made of polycarbonate. It is not possible to attach the safety guard incorrectly.
• No access to rotating tools.
• The spread of our dust is inhibited.
• Equipped with emergency stop - The tool stops rotating in less than 4 seconds (also for normal shut-down and stop via
safety guard).
• Clearance between safety guard/stand and lifting handle at least 1 31/32”.
• Noise level under 70 dB.
• Machine remains stable on a slope of up to 10o.
The machine is protected against overvoltage.
Non-ionising radiation is not produced intentionally, but rather technically conditioned by electrical equipment (e.g. electric
motors, live power lines or solenoids). The machine is equipped with strong permanent magnets. By maintaining a safe
distance (between the eld source and implant) of 11 13/16”, any impact on active implants (e.g. pacemakers, debrillators)
can likely be prevented.
The machine should be positioned to allow space for normal use and maintenance.
Good ergonomics for the user is ensured by the accompanying bowl trolley, which eliminates heavy lifting of the bowl and
maintains the right working height.
There is a risk of injury if the machine is not grounded.
The machine must only be connected to an grounded supply. See also .
Placing your hands in the bowl while the machine is running may cause physical injury.

• Powdery ingredients should not be poured into the bowl from a great height.
• Bags of e.g. our should be opened at the bottom, down in the bowl.
• Do not run up to the maximum speed too quickly.

8










When working with hot ingredients which are added via the lling hole in the safety guard, it is necessary to use the lling chute.
The lling chute is made of FDA-grade silicone, and is able to withstand hot ingredients up to 392o F. The lling chute can be
used for ingredients as hot as this for as long as necessary.
If the lling chute is  used, ingredients which are added via the lling hole in the safety guard must not be more than 140oF.


(liquid as % of dry matter)
E.g. a basic recipe includes 2.2 lbs dry matter and 1.3 lbs liquid:
this gives AR = 1.3 lbs x 100 = 60%
2.2 lbs
If, for example, the maximum capacity of the mixer is required, the calculated
AR = 60% is used to determine the amount of dry matter and liquid in the dough:
Maximum capacity of the machine = 24.2 lbs for dough with AR = 60%
Now the weight of the dry matter in this dough is calculated as follows:
Dry matter = max. capacity x 100 = 24.2 lbs x 100 = 15.16 lbs
AR + 100 60 + 100
Weight of liquid = 24.2 lbs - 15.16 lbs = 9.09 lbs
Local variations in the quality of the raw materials may a󰀨ect water absorption, volume,
baking characteristics etc., and hence capacity.
 Tool 
 Whip 2.5 qts
 Whip 5.3 qts
 * Whip 16.9 qts
  22 lbs
* 26.5 lbs
  22 lbs
  24.25 lbs
  26.5 lbs
󰀩  30.9 lbs
 Whip 11 lbs
  33 lbs
  30.9 lbs
  27.6 lbs

Bowl 20 Q
Hook, whip and beater for 20 Q bowl
A silicone lling-chute for hot ingredients

Scraper for 20 Q bowl, if mixer is tted for a scraper
Bowl 12 Q
Hook, whip and beater for 12 Q bowl
Scraper for 12 Q bowl, if mixer is tted for a scraper

Bowl trolley



9








With supporting spring

Only oor model



 







For the benet of service
sta󰀨, it should be clear to see
when the power plug to the
machine has been removed
from the socket in the wall

10

KODIAK has been designed in partnership with kitchen and bakery sta󰀨, which has resulted in a number of user benets:

Can be connected to the power grid by the user (100V-240V).
Is made of stainless steel.
The oor model has height-adjustable feet to ensure that the high bowl trolley works properly.
Is easy to clean, with large surfaces and a removable safety guard which can be machine-washed.
The power cord is connected to a waterproof silicone plug and can not be shaken from the machine (100V-240V).
The inclined control panel combined with the large bowl diameter provides a good view of the contents of the bowl.
The machine is equipped with a spring that helps to lift and lower the bowl.

The control panel is simple and intuitive, with large push buttons.
The speed can be increased/decreased continuously by holding down and . It is also possible to ‘step’ between the
predened speeds 12345678.
The panel is inclined at the ergonomically correct height, making it very comfortable to use.
The panel is easy to clean with a damp cloth.
There is a built-in timer function with a display, which can also be used to show the
number of operating hours.

The one-piece safety guard is made of transparent plastic. The safety guard is easy
to remove and clean. The safety guard can be machine-washed at up to 140o F and
can withstand up to 194oF for short periods.
The loose silicone lling chute withstands being exposed to hot ingredients up to
392o F, and is dishwasher-safe.
The safety guard is made of a special impact-resistant material which can withstand
daily use in a commercial kitchen.
The safety guard is held in place by magnets, so there are no loose parts that can
break or collect dirt.
It is not possible to attach the safety guard incorrectly.
A force corresponding to 6.6 lbs or 30 N should be used to remove the safety guard.
The lling hole in the safety guard can be turned to suit the user’s needs.

The bowl is not very deep but has a large diameter, which makes it easier to see the
contents while working.
The bowl does not have to be lifted into place in the bowl arms, but can be wheeled
directly into position.
The bowl trolley is used for transfer from mixer to workbench, dishwasher, stores etc.
The bowl trolley provides an ergonomically correct working height.
The bowl trolley spares the user any heavy lifting.
The bowl can be tilted in the rubber ring on the bowl trolley.

The machine whip is very compact in design, which provides for a long service life. It must be handled according to these
instructions.
The bowl, beater, hook and whip are made of stainless steel.

11

Floor model: Place the bowl in the bowl trolley. Put the desired
tool into the bowl and wheel it into position between the bowl
arms. Ensure that the bowl is correctly engaged with the bowl
arms; see “.
Table model: Put the desired tool into the bowl and place the
bowl in the bowl arms.
Fit the safety guard and turn it so the lling hole is accessible
when the machine is running. The loose lling chute must be
used if it is necessary to add hot ingredients during the process
(i.e. ingredients at temperatures above 140oF).
Turn the tool to lock it into the bayonet tting.
Lift the bowl with the aid of the lifting handle.
The mixer is now ready to start.
It is possible to set both the running time and speed before
starting the machine; see next section:

Press to start the machine.
Press next to to increase the speed.
Press next to to reduce the speed.
The speed is shown as a number on the scale 12345678.
The display 12345678 represents the lowest speed,
approx. 64 rpm.
The display 12345678 represents the highest speed,
approx. 353 rpm.
If a specic start speed is wanted, you set the speed and then
start the machine by pressing .

Select a running time for the machine by pressing next
to . The running time is shown in minutes and seconds in
the timer eld between and .
Running times of up to 90 minutes are available.
When the machine is running, the running time will not be reset
if is pressed once; press once more and it will be reset.
If no running time is selected, the display will show the time
elapsed since the machine was started.
If the time set on the timer runs out while the mixer is running,
the machine stops and you hear a beep.

If the machine needs to be stopped temporarily without a󰀨ecting
the running time, press . The machine will slow down and
then stop and the running time will stop too.
The bowl can now be lowered and the ingredients checked.
Lift the bowl and press , and the machine will start and the
running time will resume.

To stop the machine:
• Press . Running time not reset.
• Press twice. Running time reset.
• Press the emergency stop - the running time will be reset.
• Lower the bowl - the running time will be reset.
In all cases the machine can be restarted by pressing .
It will start at the lowest speed.








 


12
12345678
12345678
12345678
XXXXX
XXX
12345678
12345678
XXXX

The machine must not be overloaded.
Possible overload situations:
• Working with excessively tough and heavy dough
• Mixer tool exceeding the recommended speed
• Wrong mixer tool being used.
Larger lumps of fat or chilled ingredients must be reduced
before they are placed in the bowl.
Overloading will cause the frequency converter to stop the
machine.
, or will be displayed in the timer
eld.
Follow the description under “   
.

Spot the error code in the section 
and follow the suggestion for a solution.
When done, remove the error code by pressing .
The mixer can now be restarted by pressing .



The whip should not be struck against hard objects
such as the edge of the bowl. This will shorten the
life of the tool because of increasing deformation.
To make mashed potato, use the beater and then
the standard whip.

The machine may only be cleaned by trained sta󰀨
over 18 years of age.
The machine should be cleaned daily after use. It should be wiped
with a soft brush and clean water. Sulphonated soaps should be
used with care, as they destroy the lubricants in the machine.
The machine should never be rinsed with a hose.
The machine parts made of aluminium, bowl arms
and bowl trolley, must not be washed with very
alkaline cleaning agents (pH must be between 5.0
and 8.0).
Please note that the plastic safety guard may be
damaged if it is exposed to high temperatures for
a prolonged period. 
o

The lling chute is dishwasher-safe.
The soap suppliers may be able to help by recommending the
right type of soap.

Lubrication and other servicing may only be carried
out by trained sta󰀨 over 18 years of age.
The lid of the mixer may only be removed when the
cable to the power supply has been removed.
When repairs are made to the mixer head, the gear wheel and
internal gear should be lubricated with  the
needle bearings in the mixer head can also be lubricated with
this type of grease.
If the machine is supplied with an attachment drive, the gear for
the attachment drive should be lubricated with 
Way LiCa 80.
Do not use any other grease types than those specied above.

The machine may be tted with an attachment drive into
which optional accessories, such as meat mincers and
vegetable cutters, can be attached.
For further information on the assembly and use of optional acces-
sories, please refer to the manual that comes with the accessory.
The machine must be shut down when the
accessory is tted to the attachment drive.


Whip  
Cream Cake mix Bread dough
Egg whites Butter cream Rye bread
Mayonnaise Wa󰀪e mix etc.
etc. Forcemeat
etc.

13
   
 Check the safety of the safety guard:
Does the tool stop rotating when the
safety guard is tilted/removed?
Regularly

    


Call the servicer
 Test the emergency stop: Does the tool
stop rotating when the emergency stop
is activated?
Regularly

     
    

Call the servicer
 The mixer head should only be
lubricated on repair, see the section
.
During repairs



The moving parts that belong to the
bowl’s lifting mechanism all run in
maintenance-free plain bearings and
should not therefore be lubricated.
Never
 The rubber plug for covering the
opening of the attachment drive should
be on the machine and be intact.
Daily 
    
.
 Follow the instructions in the section

Follow the instructions
in the section “Cleaning”


Press the stop button for 5 sec. The machine’s data will then be displayed as alternating text in the display. There are
ve readings corresponding to the ve data sets described below:
• States rmware version, displayed as “F” followed by three gures, e.g. = rmware version 3.
• : States the machine’s running time, displayed as “t” followed by three gures, which indicate the number of
9.999-minute cycles, e.g. = 2 x 9.999 min., or 19.998 min.
• : Displays four gures, which indicate the number of minutes the current cycle has been running, e.g.
= 1.234 min.I.e., if is displayed followed by , the machine has been running for 19.998 min. + 1.234
min., or a total running time of 21.232 min.
• : States the number of times the machine has been disconnected from the power supply (plug pulled out of the
machine/power outage/switched o󰀨) and restarted, displayed as “r” followed by three gures, which indicate the number
of restarts, e.g. = 2 x 9,999 restarts, or 19,998 restarts.
• : Displays four gures, which indicate the number of restarts which have happened in the current cycle, e.g.
= 1234 times. In other words, if is displayed followed by , the machine has restarted a total of 19,998
+ 1,234 times, or 21,232 times.

It is possible to display a log of the errors that have occurred:
• Hit emergency stop and press next to .
• The display shows the latest error rst.
• To scroll back through the errors, press next to ; to scroll forward, press next to .
• The last eight errors can be displayed.
• Deactivate emergency stop to cancel the display.

14


User pressed without raising the bowl to working height.
: Raise bowl to working height.
User pressed without tting the safety guard.
: Fit the safety guard.
The Thermal sensor in the motor has overheated.
: The error will disappear when the temperature has dropped to an acceptable level.
Stop the machine and reduce the quantity of ingredients in the bowl. When it starts again, select a lower speed.
There is an error in communication between the control panel and the frequency converter.
Solution: Call the engineer.
Error in frequency converter.
: Call the engineer.
Thermal sensor in the frequency converter has cut out.
: The error will disappear when the temperature has dropped to an acceptable level.
Intermittent low voltage in the power supply.
: The power supply to the machine should be checked by an expert.
Intermittent high voltage in the power supply.
: The power supply to the machine should be checked by an expert.
[ EE:14 ] Wrong parameter in frequency converter
 Call the engineer, reference - Varimixer instruction 23020-1602
The machine is overloaded - continuously for 50 seconds.
: Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted before
the machine is restarted. When restarted, select a lower speed, if speed was the problem.
The error code is removed by pressing
The machine is overloaded - momentarily (overloaded 8 times within 20 seconds.
: Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted before
the machine is restarted. When restarted, select a lower speed, if speed was the problem.
The error code is removed by pressing
Blockage.
: Remove the object that caused the blockage.
The error code is removed by pressing
, and can also occur when using the attachment drive.

15


16
TABLE OF CONTENTS
TRANSMISSION...........................................................................................................................17
LIFTING SYSTEM.........................................................................................................................18
PLANETARY HEAD ......................................................................................................................20
ATTACHMENT DRIVE..................................................................................................................22
MACHINE COLUMN.....................................................................................................................24
FREQUENCY CONVERTER .......................................................................................................26
FRONT PANEL..............................................................................................................................27
CABLES.........................................................................................................................................28
ACCESSORIES ............................................................................................................................30
CIRCUIT DIAGRAM:.....................................................................................................................31


17
3
8
7
2
11
5
1
4
12
6
10
9
ITEM   
1RN20-87 Fan
2CR30-90 Micro-V
3STA3410 Circlip
4STA3413 Circlip
5CR20-61.3 Mounting plate motor 100/115/120/230/400/440/480V
5A CR30-61.3 Mounting plate motor 200/208V
6CR20-128 Pulley ø63
7CR20-129 Pulley ø112
8STA2037 Feather key
9STA3407 Circlip
10 STA2004 Feather key
11 CR20-85 Motor 700W 100/115/120/230/400/440/480V
11A CR30-85.1 Motor 1500W 200/208V
12 STA5834 Hexagon lock nut
12A STA5751 Hexagon cap screw 200/208V
3
8
7
2
4
5A
12A
6
10
11A
1
9
TRANSMISSION

18
LIFTING SYSTEM
ITEM  
1CR30-83.1M Lifting bolt
2STA2515 Bearing bushing
5STA3410 Circlip
6CR30-63M Crankshaft
7CR20-62M Lifting arm
8CR30-62.9 Cover
9STA3408 Circlip
10 CR20-23M Bowl arm
11 CR20-68.5 Shaft
12 CR30-63.3 Absorber plug
13 CR20-110 Spring
15 CR20-23.5 Gasket
16 STA3403 Circlip
17 STA2019 Feather Key

19
16
10
11
5
15
789 2 17 961312
1
LIFTING SYSTEM

20
ITEM  
1STA6460 Dowel pin
2STA3515 Retaining ring
36006 2RS Ball bearing
46206 2RS Ball bearing
5STA3518 Retaining ring
6HK1816 Needle bearing
7R20-235 Axial washer
8LR17 Bushing
9STA3470 Circlip
10 R20-32 Tooth wheel 1
11 R20-31 Tooth wheel
12 STA2008 Shaft key
13 LR15 Bushing
14 STA3414 Circlip
15 CR30-108R Sealing ring
16 RN20-272.1 Shell
17 CR30-34 Distance ring
18 CR30-36 Eccentric disc
19 CR30-30.5 Main shaft
20 RN20-108R Shaft gasket
21 STA5638 Socket head screw
22 CR20-33.6 Bayonet shaft
23 CR30-2.1 Lower head
24 42CR20-105 Bayonet shaft scraper
25 STA5729 Socket head screw
26 CR30-37 Distance ring
27 CR20-1 Planetary gear - machined
27 CR20-1.1 Planetary gear attachment drive
 Bayonet
 
 
 
 
 
 
 
 Bayonet
 
 
 
 
 
 
