Varimixer V30K Guide

SPARE PARTAND OPERATION MANUAL
FOOD MIXER Model V30K
May. 2019

2
LIMITED WARRANTY
Varimixer warrants its commercial mixers to the original purchaser against defects in material or manufacture for a period
of two years from the date of original purchase, subject to the following exclusions and limitations. The warranties pro-
vided by Varimixer do not apply in the following instances:
EXCLUSIONS
1. In the event that the equipment is improperly installed, adjusted and/or calibrated. Proper installation is the responsi-
bility of the installer, proper installation procedures are covered in the Varimixer Spare Parts and Operations Manual.
2. In the event that the equipment is improperly maintained. Proper maintenance is the responsibility of the user. Proper
maintenance procedures are covered in the Varimixer Spare Parts and Operations Manual.
3. In the event that failure or malfunction of the appliance or any part thereof is caused by abnormal use or is otherwise
not attributable to a defect in material or manufacture.
4. In the event that the appliance, by whatever cause, has been materially altered from the condition in which it left the
factory.
5. On parts which would normally be worn or replaced under normal conditions. (Belts, Pins, Planetary Parts, etc.)
6. Accessories such as dough hooks, wire whips, beaters and external hub attachments, etc., will have a 30 day repair
or replacement warranty. (Parts only, No labor)
7. Model V5 Teddy will have a Carry-In (LocalAuthorized Service Center) one year parts and labor warranty.
If any oral statements have been made regarding the appliance, such statements do not constitute warranties and are not
part of the contract of sale. This Limited Warranty constitutes the complete, nal and exclusive statement with regard to
warranties.
THIS LIMITED WARRANTY IS EXCLUSIVEAND IS IN LIEU OF ALL OTHER WARRANTIES WHETHER WRIT-
TEN, ORAL OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE OR WARRANTY AGAINST LATENT DEFECTS.
LIMITATIONS OF LIABILITY
In the event of warranty claim or otherwise, the sole obligation of Varimixer shall be the repair and/or replacement at the
option of Varimixer, of the appliance or component or part thereof Such repair or replacement shall be the expense of Vari-
mixer except that travel over 100 miles or two hours, overtime, and holiday charges shall be the expense of the purchaser.
Any repair or replacement under this warranty does not constitute an extension of the origin, warranty for any period for
the appliance or for any component part thereof. Parts to be replaced under this warranty will be repaired or replaced at
the option of Varimixer with new or functionally operative parts. The liability of Varimixer on any claim of any kind, including
claims based on warranty, expressed or implied, contract, negligence, strict liability or any other theories shall be solely
and exclusively the repair or replacement of the product as stated herein, an such liability shall not include, and purchaser
specically renounces any rights to recover, special, incidental, consequential or other damages of any kind whatsoever,
including, but not limited to, injuries to persons or damage to property, loss of prots or anticipated prots, or loss of use of
the product.
TO SECURE WARRANTY SERVICE
If you claim a defect covered by this Limited Warranty, direct your claim to Varimixer North America at [phone],
providing model, serial number, voltage, and a description of the problem. You will be provided with a Local Authorized
Service Representative to complete the repairs.
www.varimixerusa.com

3
Caution -READ BEFORE OPERATING- Caution
Varimixer recommends that mixer operators be at least 18 years of age and be thoroughly trained on
the use, cleaning and lubrication of the mixer.
This manual should be seen as an integral part of the mixer and should be kept by the machine
throughout its working life.
Before the machine is commissioned, it is important to read these instructions thoroughly.
The manufacturer may update the product manual without updating this copy of the manual
Varimixer recommends that the following precautions be adopted to help make the mixer operation
safer and more efficient.
- All operators should be at least 18 years of age.
- All operators should be thoroughly trained before being allowed to operate the mixer.
- NEVER reach into the bowl when the mixer is running.
- Do not wear loose clothing or rings while operating the mixer.
- Stop the mixer and lower the bowl before adding ingredients, scraping the bowl, removing the
agitator, or removing the product.
- Stop the mixer before removing or installing attachments into the drive hub.
- Do not attempt to assemble or disassemble attachments while mounted into the drive hub.
- Always use the pusher plate with the slicer/meat grinder attachments.
- NEVER bypass the safety mechanisms supplied on the mixer. Doing so can cause injury and.
is the responsibility of the user to insure these safety mechanisms are operating properly.

4
General:
This manual should be seen as an integral part of the mixer and should be kept by the machine throughout its working life.
Beforethemachine iscommissioned,itisimportant to readtheseinstructionsthoroughly,particularly thesectiononusersafety .
The manufacturer may update the product manual without updating this copy of the manual.
The manufacturer will not be liable for faults caused by:
• Careless, improper or incorrect use of the mixer
• Non-standard use (not for the purposes described in the manual)
• Incorrect installation
• Incorrect power supply to the machine
• Failure to comply with maintenance instructions
• Modicationstothemachine
• Sparepartsandaccessoriesthatarenotoriginalorspeciedforthismodel
• Failure to comply with instructions in this manual
In case of faults with the mixer, please contact the Lokal Authorized Service Agency.
UnpackinG:
The machine should be unpacked and the packaging disposed of according to regulations applicable in the country concerned.
Before the mixer is removed from the pallet, check that all parts are present with the machine:
• BowlScreen,Powercable,32mmxedspannerforlegs,Bowltrolley
• Bowl, Whip, Beater, Hook and Scraper with blade, if these were selected with the order.
The machine can be released from the pallet by cutting the strips.
contents:
General: ............................................................................................................................................................. 4
UnpackinG: ............................................................................................................................................................. 4
transport: ............................................................................................................................................................. 5
installation and adjUstments: ................................................................................................................................ 5
electrical connection:........................................................................................................................................... 6
technical data: ...................................................................................................................................................... 6
max. capacity of the machine: ................................................................................................................................. 6
commissioninG:........................................................................................................................................................ 7
recommended Use of the machine:........................................................................................................................... 7
safety: ............................................................................................................................................................. 7
WorkinG With hot inGredients:................................................................................................................................ 8
eqUipment: ............................................................................................................................................................. 8
maGnets: ............................................................................................................................................................. 8
components of the machine: ................................................................................................................................... 9
kodiak User-friendliness: ................................................................................................................................. 10
operatinG the machine: ..........................................................................................................................................11
overloadinG:........................................................................................................................................................ 12
procedUre in case of overloadinG:....................................................................................................................... 12
recommended speeds: ........................................................................................................................................... 12
recommended speeds for attachment drive: .......................................................................................................... 12
correct Use of tools:.......................................................................................................................................... 12
cleaninG: ........................................................................................................................................................... 12
lUbrication and Grease types: .............................................................................................................................. 12
attachment drive:................................................................................................................................................. 12
systematic maintenance: ....................................................................................................................................... 13
readinG the machines data:................................................................................................................................... 13
readinG the error loG: ........................................................................................................................................ 13
error codes and possible solUtions:.................................................................................................................... 14
access to the fUse:.............................................................................................................................................. 15
circUit diaGram: ................................................................................................................................................... 16
mixer spare parts ............................................................................................................................................... 17

5
transport:
Lifting equipment should always be used to move the machine.
The machine must not be pulled or lifted by the bowl lift handle.
When the machine is moved, it should be in a vertical position at all times.
installation and adjUstments:
The ambient temperature around the machine must not exceed 113o F.
When the mixer is delivered, the adjustable feet will be turned right to the
bottom. The height of the legs should be adjusted so that the bowl on
thebowltrolleytsperfectlyintothebowlarms.
Thebowlarmsshouldbeatthecorrectheightabovetheoorbefore
the machine is taken into use – see Adjustments.
Adjustments:
Together with the mixer
comes a 32 mm fixed
spanner to be used for
adjustments.
To raise leg
turn
clockwise
To lower leg
turn
anticlockwise
It is of the outmost importance that the legs of the machine are
adjusted so that the conditions in the following sketch are met.
Condition 1:
Thetopofthemixermustbeparalleltotheoor.Toensurethisyoumustmeasure
thedistancefromthetopofthemachinetotheoor:
The dimension must be the same when measured at the front of the mixer
and at the rear of the mixer:
Condition 2
Themixermustbeheightadjustedsothatthebowlonthebowltrolleytsexactly
in the bowl arms:
Basically,thedimensionfromoortocentreoftheknobsonthebowlarmsmust
be 34 1/16”.Ifthebowlonthebowltrolleydoesnottexactlyinthebowlarms
at this dimension, adjust slightly on the front legs of the mixer.
12
86,5cm

6
53 13/16”
24 9/16”
22 1/8”
19 7/16”
31 3/16”
max. capacity of the machine:
AR = absorption ratio (%AR)
(liquid as % of dry matter)
E.g. a basic recipe includes 2.2 lbs dry matter and 1.3 lbs liquid:
this gives AR = 1.3 lbs x 100 = 60%
2.2 lbs
If, for example, the maximum capacity of the mixer is required, the calculated AR =
60% is used to determine the amount of dry matter and liquid in the dough:
Maximum capacity of the machine = 28.7 lbs for dough with AR = 60%
Now the weight of the dry matter in this dough is calculated as follows:
Dry matter = max. capacity x 100 = 28.7 lbs x 100 = 17.9 lbs
AR + 100 60 + 100
Weight of liquid = 28.7 lbs - 17.9 lbs = 10.8 lbs
Capacity per mix Tool KODIAK30
Egg white Whip 3.17 Qts
Mayonnaise Whip 21.13 Qts
Yeast dough (60% AR) Hook 28.7 lbs
Meatball mix Beater 44.1 lbs
Local variations in the quality of the raw materials may
affect water absorption, volume, baking characteristics
etc., and hence capacity.
electrical connection:
Voltage ratio at site
100V - 240V, 1 phase =
User can connect machine
Before the machine is connected to the mains, check that
the voltage and frequency printed on the name plate are
correct for the installation location.
The name plate is positioned uppermost on the back of the machine.
The machine must be earthed. Failure to do so may cause injury.
Ifthereisnoearthconnection,theEMClterwillnotwork,withthe
risk of damage to the frequency converter.
Cable with plug is delivered with the machine
Only this cable must be used for the connection
The machine must only be connected to an
earthed mains supply
Thecableisxedtothemachineintheplugmadeofsili-
cone, see “Components of the machine” page 9
The machine is protected by a 10Afuse built into the socket
on the back of the machine.
Voltage ratio at site
380 - 480 V, 2 or 3 phases, neutral or not =
Technician must connect machine
Cable without plug is connected to the machine
the cable must be mounted in the wall socket
The machine must only be connected to an
earthed mains supply
When the machine is connected, phase + neutral + earth
or phase + phase + earth should be used. In both cases,
it is important to ensure that the voltage between the two
live pins matches the name plate.
Gross
weight 485 lbs
Net
weight 418 lbs
HP 1.6
Volts 208V
Amps 8.3A
Variable
speed,
tool 64 – 353 rpm
technical data:
NOTE
The machine must be protected
by a Residual Current Device:
Installation in industrial environ-
ment: HPFI type A-SI / PFI type B
Housing, business, light indus-
try: HPFI type A-SI

7
commissioninG:
Bowl, tools and Bowl Screen should be cleaned before use – see section on Cleaning, page 12.
Thebowlarmsshouldbeatthecorrectheightabovetheoorbeforethemachineistakenintouse–seeAdjustments, page 5.
recommended Use of the machine:
The machine is designed for the manufacture of products that do not trigger any reactions or release substances
that may be harmful to the user when in use.
The machine must not be used in an explosive atmosphere.
The machine must only be operated by staff who have been trained in the use of the machine according to these
instructions. Users must be over 18 years of age.
The machine is designed for commercial use in kitchens, catering outlets and bakeries.
Themachinemayonlybeusedasspeciedinthismanual.
Only bowls designed for Kodiak 30 may be used. Tools should be used in conjunction with the corresponding bowl – a 30 Q tool
with the 30 Q bowl and a 30/15 Q tool with the 30/15 Q bowl
Unless the change is recommended by the manufacturer, modifying the machine is prohibited.
Ifthemachineisttedwithanattachmentdrive,onlyaccessoriesproducedorrecommendedbymanufacturershouldbeattached.
safety:
The machine is designed for the manufacture of products that do not trigger any reactions or release substances
that may be harmful to the user when in use.
Users must be over 18 years of age and trained in the use of the machine according to these instructions.
User safety is assured as follows:
• Tools can only rotate when the bowl screen is in place and the bowl is lifted.
• The bowl screen is made of plastic. It is not possible to attach the guard incorrectly.
• No access to rotating tools.
• Thespreadofourdustisinhibited.
• Equipped with emergency stop - The tool stops rotating in less than 4 seconds (also for normal shut-down and stop via
bowl screen).
• Clearance between guard/stand and lifting handle at least 1 31/32”.
• Noise level under 70 dB.
• Machine remains stable on a slope of up to 10o.Thedistancefromtheoortothebowlarmshouldbeadjustedasshown
in the section on Adjustments, page 5.
The machine is protected against overvoltage.
Non-ionising radiation is not produced intentionally, but rather technically conditioned by electrical equipment (e.g. electric mo-
tors, live power lines or solenoids). The machine is equipped with strong permanent magnets. By maintaining a safe distance
(betweentheeldsourceandimplant)of1113/16”,anyimpactonactiveimplants(e.g.pacemakers,debrillators)canlikely
be prevented.
The machine should be positioned to allow space for normal use and maintenance.
Good ergonomics for the user is ensured by the accompanying bowl trolley, which eliminates heavy lifting of the bowl and
maintains the right working height.
The following recommendations apply to work with powdery ingredients:
• Powdery ingredients should not be poured into the bowl from a great height.
• Bagsofe.g.ourshouldbeopenedatthebottom,downinthebowl.
• Do not run up to the maximum speed too quickly.
There is a risk of injury if the machine is not earthed.
The machine must only be connected to an earthed mains supply. See also ‘Electrical Connection’page 6’.
Placing your hands in the bowl while the machine is running may cause physical injury.

8
Warning for users with implants (e.g. pacemakers, debrillators).
Mixer and safety guard equipped with strong magnets
Areas on mixer and
bowl with magnets -
for bowl detection
Area on safety guard with magnets
Area on mixer with
magnets - for safety
guard switch
WorkinG With hot inGredients:
Whenworkingwithhotingredientswhichareaddedviathellingholeinthebowlscreen,itisnecessarytousethellingchute.
ThellingchuteismadeofFDA-gradesilicone,andisabletowithstandhotingredientsupto392o F.Thellingchutecanbe
used for ingredients as hot as this for as long as necessary.
Ifthellingchuteisnotused,ingredientswhichareaddedviathellingholeinthebowlscreenmustnotbemorethan140oF.
maGnets:
Standard equipment, as follows:
Bowl 30 Q
Hook, whip and beater for 30 Q bowl
Asiliconelling-chuteforhotingredients
Bowl trolley
Optional accessories:
Scraperfor30Qbowl,ifmixeristtedforascraper
Bowl 15 Q
Hook, whip and beater for 15 Q bowl
Scraperfor15Qbowl,ifmixeristtedforascraper
eqUipment:

9
Socket on the back of the
machine; contains 10A fuse,
see page 15.
Lifting handle
Bowl truck
Bowl
Control panel
Bowl Screen
Mixer head
Adjustable legs; see
page 5 for adjustment
Bowl arms; see page 5
for attachment between
bowl arms and bowl
Control panelwith
attachment drive
components of the machine:
Forthebenetofservice
staff, it should be clear to see
when the mains plug to the
machine has been removed
from the socket in the wall

10
kodiak User-friendliness:
KODIAKhasbeendesignedinpartnershipwithkitchenandbakerystaff,whichhasresultedinanumberofuserbenets:
The machine itself
Can be connected to the mains by the user
Is made of stainless steel
Has height-adjustable feet to ensure that the high bowl trolley works properly
Is easy to clean, with large surfaces and a removable safety guard which can be machine-washed
The power cord is connected to a waterproof silicone plug and can not be shaken from the machine
The inclined control panel combined with the large bowl diameter provides a good view of the contents of the bowl.
The machine is equipped with a spring that helps to lift and lower the bowl
Control panel:
The control panel is simple and intuitive, with large push buttons.
The speed can be increased/decreased continuously by holding down and . It is also possible to ‘step’ between the
predenedspeeds
The panel is inclined at the ergonomically correct height, making it very comfortable to use.
The panel is easy to clean with a damp cloth.
There is a built-in timer function with a display, which can also be used to show the number
of operating hours.
Bowl screen:
The one-piece bowl screen is made of transparent plastic. The screen is easy to remove
and clean. The screen can be machine-washed at up to 140oFand can withstand up to
194oF for short periods (Max 20 sec.)
Theloosesiliconellingchutewithstandsbeingexposedtohotingredientsupto392oF,
and is dishwasher-safe
The screen is made of a special impact-resistant material which can withstand daily use in
a commercial kitchen.
The bowl screen is held in place by magnets, so there are no loose parts that can break
or collect dirt.
It is not possible to attach the screen incorrectly.
A force corresponding to 6.6 lbs or 30 N should be used to remove the screen.
Thellingholeinthebowlscreencanbeturnedtosuittheuser’sneeds.
Bowl and bowl trolley:
The bowl is not very deep but has a large diameter, which makes it easier to see the con-
tents while working.
The bowl does not have to be lifted into place in the bowl arms, but can be wheeled directly
into position.
The bowl trolley is used for transfer from mixer to workbench, dishwasher, stores etc.
The bowl trolley provides an ergonomically correct working height.
The bowl trolley spares the user any heavy lifting.
The bowl can be tilted in the rubber ring on the bowl trolley.
Tools:
Themixerwhip is very compact in design,which provides for along service life.It must be handledaccording to these instructions.
The beater and hook are made of stainless steel.

11
Before starting the machine:
Place the bowl in the bowl trolley. Put the desired tool into the
bowl and wheel it into position between the bowl arms. Ensure
that the bowl is correctly engaged with the bowl arms; see “In-
stallation and adjustments”, page 5.
Fitthebowlscreenandturnitsothellingholeisaccessible
when the machine is running. Theloosellingchutemustbe
used if it is necessary to add hot ingredients during the process
(i.e. ingredients at temperatures above 140oF).
Turnthetooltolockitintothebayonettting.
Lift the bowl with the aid of the lifting handle.
The machine is now ready to start.
Itispossible to set both the running timeand speed before start-
ing the machine; see next section:
Start the machine:
Press to start the machine.
Press next to to increase the speed.
Press next to to reduce the speed.
The speed is shown as a number on the scale .
The display 1represents the lowest speed, ap-
prox. 64 rpm.
The display 12345678represents the highest speed, ap-
prox. 353 rpm.
Ifaspecicstartspeediswanted,yousetthespeedandthen
start the machine by pressing .
Display of running time – Timer function:
Select a running time for the machine by pressing next to
. The running time is shown in minutes and seconds in the
timereldbetween and .
Running times of up to 90 minutes are available.
When the machine is running, the running time will not be reset
if ispressed once; press once moreand itwill bereset.
If no running time is selected, the display will show the time
elapsed since the machine was started.
If the time set on the timer runs out while the mixer is running,
the machine stops and you hear a bib.
Inspection of ingredients while in use:
Ifthemachineneedsto be stopped temporarily without affecting
the running time, press . The machine will slow down and
then stop and the running time will stop too.
The bowl can now be lowered and the ingredients checked.
Lift the bowl and press , and the machine will start and the
running time will resume.
Stop the machine:
To stop the machine:
• Press . Running time not reset.
• Press twice. Running time reset.
• Press the emergency stop - the running time will be reset.
• ‘Tilt’ the bowl screen - the running time will be reset.
• Lower the bowl - the running time will be reset.
In all cases the machine can be restarted by pressing .
It will start at the lowest speed.
operatinG the machine:
Emergency stop
Stop
Increase time
Timer (timer eld)
Decrease time
Speed indi-
cator
Decrease speed Increase speed
Start

12
12345678
12345678
12345678
XXXXX
XXX
12345678
12345678
XXXX
overloadinG:
The machine must not be overloaded.
Possible overload situations:
• Working with excessively tough and heavy dough
• Mixer tool exceeding the recommended speed
• Wrong mixer tool being used.
Larger lumps of fat or chilled ingredients must be reduced
before they are placed in the bowl.
Overloading will cause the frequency converter to stop the
machine.
, or will be displayed in the timer
eld.
Follow the description under “Procedure in case of over-
loading”.
procedUre in case of overloadinG:
Spot the error code in the section “Error codes and possible
solutions”, page 14 and follow the suggestion for a solution.
When done, remove the error code by pressing .
The mixer can now be restarted by pressing .
recommended speeds:
correct Use of tools:
Recommended uses of tool:
The whip should not be struck against hard objects
such as the edge of the bowl. This will shorten the
life of the tool because of increasing deformation.
To make mashed potato, use the beater and then
the standard whip.
cleaninG:
Themachinemay onlybe cleanedbytrainedstaff
over 18 years of age.
Themachineshould be cleaned dailyafteruse.Itshould be wiped
with a soft brush and clean water. Sulphonated soaps should be
used with care, as they destroy the lubricants in the machine.
The machine should never be rinsed with a hose.
Themachinepartsmadeof aluminium, bowl armsand
bowl trolley, must not be washed with very alkaline
cleaning agents (pH must be between 5.0 and 8.0).
Please note that the plastic bowl screen may be
damaged if it is exposed to high temperatures for
a prolonged period. (Max. temperature 140
o
F)
Thellingchuteisdishwasher-safe
The soap suppliers may be able to help by recommending the
right type of soap.
lUbrication and Grease types:
Lubrication and other servicing may only be carried
out by trained staff over 18 years of age.
The lid of the mixer may only be removed when the
cable to the mains supply has been removed.
When repairs are made to the mixer head, the gear wheel and
internal gear should be lubricated with Molykote G-1502 the
needle bearings in the mixer head can also be lubricated with
this type of grease.
If the machine is supplied with an attachment drive, the gear
for the attachment drive should be lubricated with Statoil
GreaseWay LiCa 80.
Donotuseanyothergreasetypesthanthosespeciedabove.
attachment drive:
Themachinemaybettedwithanattachmentdriveinto
which optional accessories, such as meat mincers and veg-
etable cutters, can be attached.
For further information on the assembly and use of optional acces-
sories, please refer to the manual that comes with the accessory.
Themachinemustbeshutdownwhentheaccessory
isttedtotheattachmentdrive.
recommended speeds for attachment drive:
Whip Beater Hook
Cream Cake mix Bread dough
Egg whites Buttercream Rye bread
Mayonnaise Wafemix etc.
etc. Forcemeat
etc.

13
Part Action Frequency Note
Bowl screen Check the safety of the bowl screen:
Does the tool stop rotating when the
screen is tilted/removed?
Regularly If the tool does not immediately
stop rotating on tilting/removal of
the screen, the machine must not
be used.
Call the engineer
Emergency stop Testthe emergencystop:Doesthe tool
stoprotatingwhen the emergencystop
is activated?
Regularly
If the tool does not immedia-
tely stop rotating on activation of the
emergency stop, the machine must
not be used.
Call the engineer
Mixer head The mixer head should only be lubri-
cated on repair, see the section “Lub-
rication and grease types”.
During repairs
The machine’s
other moving
parts
The moving parts that belong to the
bowl’s lifting mechanism all run in
maintenance-free plain bearings and
should not therefore be lubricated.
Never
Attachmentdrive Therubberplugforcoveringtheopen-
ing of the attachment drive should be
on the machine and be intact.
Daily The rubber plug must cover the
opening on the attachment drive
when the latter is not in use.
Cleaning Follow the instructions in the section
“Cleaning” Follow the instructions in the section “Cleaning”
systematic maintenance:
readinG the machines data:
Pressthestopbuttonfor5sec.Themachine’sdatawillthenbedisplayedasalternatingtextinthedisplay.Thereareve
readingscorrespondingtothevedatasetsdescribedbelow:
• Data set 1: Statesrmwareversion,displayedas“F”followedbythreegures,e.g. =rmwareversion3.
• Data set 2:States the machine’srunningtime,displayed as “t”followed by threegures, which indicatethenumber of
9.999-minute cycles, e.g. = 2 x 9.999 min., or 19.998 min.
• Data set 3:Displaysfourgures,whichindicatethenumberofminutesthecurrentcyclehasbeenrunning,e.g. =
1.234 min.I.e., if is displayed followed by , the machine has been running for 19.998 min. + 1.234 min.,
or a total running time of 21.232 min.
• Data set 4: States the number of times the machine has been disconnected from the power supply (plug pulled out of the
machine/powercut/switchedoff)andrestarted,displayedas“r”followedbythreegures,whichindicatethenumberofrestarts,
e.g. = 2 x 9,999 restarts, or 19,998 restarts.
• Data set 5:Displaysfourgures,whichindicatethenumberofrestartswhichhavehappenedinthecurrentcycle,e.g.
= 1234 times. In other words, if is displayed followed by , the machine has restarted a total of 19,998 +
1,234 times, or 21,232 times.
readinG the error loG:
It is possible to display a log of the errors that have occurred:
• Hit emergency stop and press next to .
• Thedisplayshowsthelatesterrorrst.
• To scroll back through the errors, press next to ; to scroll forward, press next to .
• The last eight errors can be displayed.
• Deactivate emergency stop to cancel the display

14
error codes and possible solUtions:
For some errors, the control system will show an error code in the display:
User pressed without raising the bowl to working height.
Solution: Raise bowl to working height.
User pressed withoutttingthesafetyguard.
Solution: Fit the bowl screen.
The Thermal sensor in the motor has overheated.
Solution: The error will disappear when the temperature has dropped to an acceptable level.
Stop the mixer and reduce the quantity of ingredients in the bowl. When it starts again, select a lower speed.
There is an error in communication between the control panel and the frequency converter.
Solution: Call the engineer.
Error in frequency converter.
Solution: Call the engineer.
Thermal sensor in the frequency converter has cut out.
Solution: The error will disappear when the temperature has dropped to an acceptable level.
Intermittent low voltage in the power supply.
Solution: The power supply to the mixer should be checked by an expert.
Intermittent high voltage in the power supply.
Solution: The power supply to the mixer should be checked by an expert.
The mixer is overloaded - continuously for 50 seconds
Solution: Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted before
the machine is restarted. When restarted, select a lower speed, if speed was the problem
The error code is removed by pressing
The mixer is overloaded - momentarily (overloaded 8 times within 20 seconds
Solution: Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted before
the machine is restarted. When restarted, select a lower speed, if speed was the problem.
The error code is removed by pressing
Blockage.
Solution: Remove the object that caused the blockage.
The error code is removed by pressing
, and can also occur when using the attachment drive.

15
access to the fUse:
If the fuse burns out, it can be replaced without the aid of technical staff.
• The fuse is located in the socket on the back of the machine.
• Be sure to remove the power cord before changing the fuse

16
circUit diaGram:
Page Previous page: Next page: Total no. of pages:
Last print: Last edit: Page rev.: Project rev.:
Appr. (date/init): Eng. (proj/page): Dwg. no.: Case no.:Project title:
Customer: Page title: File name: Page ref.:
DCC: Scale:
Kodiak VL1C 5
1529-08-2018
Diagram
PCSCHEMATIC Automation
38.020-13.02.01 29-08-2018 4
6
01
CE/ CE
&FS 1:1
1 2 3 4 5 6 7 8
Supply Plug Supply Plug Supply Plug
12 12
-S3
Safety guard magnet affected
12 12
-S2
PTO PTO
PE
L!
L2
L3
M
3
PTO PTO
PE
L!
L2
L3
-M1
Main motor 1.5W (PTO)
11 11
-X2
44 44
55 55
55 55
44 44
33 33
-X6
22 22
11 11
66 66
1
2 3 1 2 3
-S5
Bowl switch 2
1
2 31
2 3
-S4
Bowl switch 1
BN
BU
YE/GN
BU
BN
BN
BU
YE/GN
BU
BN
-W3
GN
BK
RD
Shield
GN
BK
RD
Shield
-W2
Modbus rtu rs485
GY
WH/RD
WH/BN
WH/BK
GY
WH/RD
WH/BN
WH/BK
-W1
/.1
6666
-X3
9999
55
55
77
77
88
88
BK 5
BK 4
BK 3
BK 2
BK 1
PE
S
BK 5
BK 4
BK 3
BK 2
BK 1
PE
S
-W6
Motor cable
S
-X7
RAMME
BN
BU
YE/GN
BU
RD
BN
BU
YE/GN
BU
RD
-W4
L3
PE
1
4
L2
5
N
L1
L1
PE
+24V
LI4 L3
PE
1
4
L2
5
N
L1
L1
PE
+24V
LI4
-Q1 Frequency
Converter
VT
WH
BN
GY
BK
GNYE
VT
WH
BN
GY
BK
GNYE
-W5
WH/OG
WH/YE
WH/VT
WH/GY
WH/BU
WH/OG
WH/YE
WH/VT
WH/GY
WH/BU
-W1
/.1
3
4
4
5
1
L1
1
2
11
10
N
12
13
7
PEL1 N-
9
15
5
14
3
4
4
5
1
L1
1
2
11
10
N
12
13
7
PEL1 N-
9
15
5
14
-K1 PCB
1112 1112
-S1
Emergency
stop
2122 2122
22
22
-X1
1111
RD
OR
BK
YE
RD
OR
BK
YE
-W1
/.1 /.2
4444
33
33
L1L1L1L1
-X5
L2/NL2/N
PE
PE
-F2
11 11
-X4
22 22 BU
BN
BU BN
-W7
-T1
Communication & safty Motor control
Frequency Converter boxs
Bowl detection
Skærm
2mm2
4 pcs. PE fasteners in the heat sink plate
S:240V P:208
BU
RD BK
BU
VT
YE/GN

17
mixer spare parts

18
mixer spare parts
TRANSMISSION.................................................................................................................... 19
LIFTING SYSTEM.................................................................................................................. 20
PLANETARY HEAD............................................................................................................... 22
ATTACHMENT HUB .............................................................................................................. 24
MACHINE COLUMN.............................................................................................................. 26
FREQUENCY INVERTER...................................................................................................... 28
FRONT PANEL...................................................................................................................... 29
CABLES................................................................................................................................. 30
ACCESSORIES ..................................................................................................................... 31

19
TRANSMISSION
PARTS LIST Name UKName
Part number
ITEM Micro-V PJ1016-12Micro-V PJ1016-12CR30-901 Mounting plate motorMotor pladeCR30-61.32 Circlip A25Seegerring A25STA34103 Hex cap screw M8x16
Sekskantskrue med flange M8x16
STA5751
4Fan 1,2kw headline motorVentilator 1,2kw Headline motor
RN20-87.15 Pulley ø112 J12Poly-v remskive ø112 J12
CR20-1296 Pulley ø63 J12Poly-v remskive ø63 J12
CR20-1287 Circlip A19Seegerring A19STA34078 Motor 1,5kwMotor 1,5wkCR30-85.29 Pasfeder AB 6x6x27mm Din6885APasfeder AB 6x6x27mm Din6885A
STA200410 Pasfeder A 8x7x22mm Din6885APasfeder A 8x7x22mm Din6885A
STA203711
3
11
6
1
8
5
9
2
4
7
10
ITEM Part number Name UK
1CR30-90 Micro-V PJ1016-12
2CR30-61.3 Mounng plate motor
3STA3410 Circlip A25
4STA5751 Hex cap screw M8x16
5RN20-87.1 Fan 1,2kw headline motor
6CR20-129 Pulley ø112 J12
7CR20-128 Pulley ø63 J12
8STA3407 Circlip A19
9CR30-85.2 Motor 1,5kw
10 STA2004 Pasfeder AB 6x6x27mm Din6885A
11 STA2037 Pasfeder A 8x7x22mm Din6885A

20
LIFTING SYSTEM
ITEM Part number Name
1STA5806 Hexagon nut M10 DIN125AA2
2STA6205 Spring cotters for bolt ø2,5
3CR30-83.1 Lifting bolt
4STA3410 Circlip A25
5CR30-63M Crankshaft
6CR20-62M Lifting arm
7CR30-62.9 Cover for liftarm
8STA3408 Retainningring A20
9CR30-65.1M Liftingnut mounted
10 CR20-110 Spring bowllift
11 CR20-23.5 NSF Gasket
12 STA3403 Circlip A12
13 CR30-63.3 Absorber plug
14 CR20-68.5 Shaft
15 STA2019 Feather Key 6x6x10
16 CR30-23M Bowl arm mounted with pins/bushing