VAS XL50-2MC User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 1
50”3-in-1 Console
Option 1: Console with Swinging Floater
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this
item to the Retailer Store. Please call our toll free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.whalenfurniture.com EMAIL: [email protected]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
XL50-2MC
MODEL # XL50-2MC
LOT NUMBER:
DATE OF PURCHASE: / /

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 2
QUALITY GUARANTEE
We are confident that you will be delighted with your VAS Furniture purchase.
Should this product be defective in workmanship or materials or fail under
normal use, we will repair or replace it for up to 1 year from date of purchase.
Every VAS Furniture product is designed to meet your highest expectations.
We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST Monday to Friday
www.whalenfurniture.com
MANUFACTURER: VAS FURNITURE
CATALOG: 50”3-in-1 Console (XL50-2MC)
DATE OF MANUFACTURE: January, 2010
MADE IN CHINA
FITS UP TO MOST 56”FLAT PANEL TV’S
MAXIMUM LOAD 135 LB (61.2 kg)
FITS UP TO MOST 56”FLAT PANEL TV’S WITHOUT
SWIVELING BRACKET
MAXIMUM LOAD 135 LB (61.2 kg)
STOPPER
MAXIMUM LOAD 50 LB (22.7 kg)
Make sure TV is placed behind Stopper.
This unit is intended for use only with the products and maximum
weights indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury. The base of the television must
be placed squarely in the center of the stand with no overhanging on either side.

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 3
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
A-Top Shelf Frame (1) B- Middle Shelf Frame (1)
C- Bottom Shelf Frame (1) D- Long Spine (1)
E- Left Leg (1) F- Right Leg (1) G- Top Glass (1)
H- Glass Shelf (2) I- Front Left Support (1) J- Front Right Support (1)
K- Back Left Support (1) L- Back Right Support (1) M- Swiveling Bracket (1)
N- XYZ Mounting Frame (1) O- Monitor Bracket (2) P- Safety Bar (1)

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 4
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
(1) - Suction Cup (12+1 extra) (2) - 3/4” Bolt (40+2 extra) (3) - 1 1/4” Bolt (6+1 extra)
(4)- Nut (5) - Lock Washer (6) - Flat Washer
(4+1 extra) (46+2 extra) (50+2 extra)
(10) - Glass Raiser (8+1 extra) Open Wrench (1) Allen Wrench (2)
Touch-Up Pen (1) Tipping Restraint Hardware Kit (1)
(Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)
M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen Wrench (provided), Open Wrench (provided) and Phillips Screwdriver.

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 5
Assembly Instructions
Note: Please do not fully tighten all bolts until you finish assembling all parts, then go
back and fully tighten all bolts, this will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Locate Long Spine (D) and set back face down on a scratch free surface as shown in detail
#1.
3. Align the holes on back rail of three Shelf Frames (A, B & C) with the threaded inserts on the
Long Spine (D), insert and screw 1 1/4”Bolts (3) with Lock Washers & Flat Washers (5 & 6)
through the pre-drilled holes on back rail into the threaded inserts included in the Spine.
Ensure the edge with two holes of end brackets will face the floor as shown in detail #1.
3
5
D
A/B/C D
Required hardware in this step
Description: (3) –1 1/4” Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (6pcs) (6pcs) (6pcs)
Tools required: Allen Wrench

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 6
Assembly Instructions
4. Stand the unit upright.
5. Align and attach Left Leg (E) to three Shelf Frames (A, B & C) in place by inserting the 3/4”
Bolts (2) with Washers (5 & 6) through the end bracket holes of shelf frames into the
threaded inserts on the Left Leg. See detail #2. DO NOT tighten the bolts.
6. Repeat last step with Right Leg (F).
E/F
DE
F
Required hardware in this step
Description: (2) - 3/4” Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (18pcs) (18pcs) (18pcs)
Tools required: Allen Wrench

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 7
Assembly Instructions for Table-top
7. For a stable structure, align and attach Front Left Support (I) and Front Right Support (J) in
place to connect the Top Shelf Frame (A) with Left & Right Legs (E & F) using 3/4” Bolts (2)
with Washers (5 & 6) through the end bracket hole, as shown in detail #3A.
8. Align and attach Back Left Support (K) and Back Right Support (L) to the Top Shelf Frame
(A) and Long Spine (D) using the 3/4” Bolts (2) and Washers (5 & 6). See detail #3.
D
E
F
FE
6
I
A
J
A
A
D
KL
6
2
6
Required hardware in this step
Description: (2) - 3/4” Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (12pcs) (12pcs) (12pcs)
Tools required: Allen Wrench

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 8
Assembly Instructions
9. Go back and tighten all bolts with Allen Wrench provided.
10.In case of uneven floor, Floor Levelers are provided at the bottom of both Legs (E & F) and
the support leg on Bottom Shelf Frame (C). Simply tilt the unit back and raise or lower floor
leveler by hand to correct tilting as shown in detail #4.
Parts provided Tools required
Pre-attached Floor Leveler No tool required

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 9
Assembly Instructions
11.Align and attach Swiveling Bracket (M) to the top of Long Spine (D) using six 3/4” Bolts (2)
with Washers (5 & 6). Make sure the swivel bolt head is up. See detail #5.
Note: The Spine can provide four height options for your TV set. Refer to your TV size, adjust
the Swiveling Bracket at your desired height to offer optimum viewing.
Required hardware in this step
Description: (2) - 3/4” Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (6pcs) (6pcs) (6pcs)
Tools required: Allen Wrench

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 10
Assembly Instructions
12.Hold the flat side of XYZ Mounting Frame (N) onto the Swiveling Bracket (M) ensuring the
hook on the side of Mounting Frame is bottom. Align and attach by threading four 3/4” Bolts
(2) with Flat Washers (6) through the metal plate on XYZ Mounting Frame and the Swiveling
Bracket, at the other side of Swiveling Bracket place the other Flat Washers (6) and Lock
Washers (5), and then secure with Nuts (4). Securely tighten with Open Wrench and Allen
Wrench provided. See detail #6.
MNMN
5
5
6
C
E
F
D
Required hardware in this step
Description: (2) - 3/4” Bolt (4) - Nut (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (4pcs) (4pcs) (4pcs) (8pcs)
Tools required: Allen Wrench and Open Wrench

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 11
Mounting Monitor Bracket to a television with a flat back
Note: For televisions with a curved back or recessed back proceed directly to step #16.
13.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
14.Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Short Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket
(O), and into the upper threaded inserts of TV. As shown in detail #7A. Note: Lean the TV up
against a wall or other solid surface when attaching with the Monitor Brackets (O). DO NOT
place the TV face down on the glass this may cause permanent damage.
15.Proceed to insert the long Bolt through the appropriate Lock Washer, the Flat Washer, the slot
of Monitor Bracket (O), a second Flat Washer (M4/M5 Diameter Bolts only), appropriate
Spacer, and into the bottom threaded inserts of TV. As shown in detail #7. Make sure the
Monitor Brackets (O) are centered and level with each other. Tighten the bolts securing the
Monitor Brackets to the TV.
Parts provided Qty Tools required
O –Monitor Bracket (2) Phillips Screwdriver
TV Mounting Kit

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 12
Mounting Monitor Bracket to a television with a curved / recess back
16.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
17.Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Bolt through the appropriate Lock Washer, the Large Flat Washer, the Monitor
Bracket (O), a second Large Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer
and into the threaded inserts of TV. See detail #8.
18.Make sure the Monitor Brackets (O) are vertically centered and level with each other.
Tighten the bolts to secure the Monitor Brackets to the TV.
Parts provided Qty Tools required
O –Monitor Bracket (2) Phillips Screwdriver
TV Mounting Kit

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 13
Assembly Instructions
MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGRRE ANGLE
PRIOR TO INSTALLATION OF TV
19.Once the Monitor Brackets (O) are attached onto the back of television, ask for assistance
to lift the television up to the XYZ Mounting Frame (N). Place the hooks on Monitor Brackets
over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to
center the television.
20.Insert the Safety Bar (P) into the bottom holes on the side of XYZ Mounting Frame (N) by
sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into
the slot of hook so that it is facing wall. Make sure it sits over the bottom hook of the Monitor
Brackets. See detail #9.
Parts provided Qty Tools required
P–Safety Bar (1) No tool required

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 14
Assembly Instructions
21.Put the Suction Cups (1) firmly into top holes of the Middle Shelf Frame (B) & Bottom Shelf
Frame (C) as shown in detail #10A.
22.Screw the Glass Raisers (10) onto the top holes of Top Shelf Frame (A) & both Legs (E & F).
Make sure they go all the way in. See detail #10.
23.Place the Top Glass (G) & Glass Shelves (H) in place as shown in detail #10. Make sure the
glass is properly centered and the black side of glass is down. Push each glass all the way
back against the Spine. Also, be sure to press down evenly and firmly each glass onto the
Suction Cups or Glass Raisers to make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the
glass shelf from falling and getting damage. If glass is scratched you can repair by using a
BLACK marker and filling in scratched area from underneath.
TV
B/C
1
H
A
B
C
E
G
H
H
10
G
E/F
A
Hardware provided Sketch Qty
(1) –Suction Cup (12pcs)
(10)- Glass Raiser (8pcs)

Model # XL50-2MC
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 15
TIPPING RESTRAINT HARDWARE
Note: We have included one Tipping Restraint Hardware bag for this Unit.
When properly installed, this restraint can provide protection against the unexpected tipping
of the Unit due to small tremors, bumps or climbing. We strongly recommend mounting this
hardware to a wall stud and your unit when installing.
Please carefully read the instructions printed on the plastic bag.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent
any accidents or damage to the unit.
Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
A Touch-Up Pen has been provided to repair any small nicks or scratches that may occur
during assembly or shipping.
Your assembly should now be complete.
Thank you for your purchase.

IF YOU REQUIRED TO ORDER PARTS PLEASE USE THE LIST BELOW
50” 3-in-1 Console (XL50-2MC)
*XL50-2MC-1-LS Long Spine *XL50-2MC-19-TRHK Tipping Restraint Hardware Kit *XL50-2MC-37-1 3/4CA 1 3/4” Concrete Anchor *XL50-2MC-2-SS Short Spine *XL50-2MC-20-LS Large Spacer *XL50-2MC-38-GR Glass Raiser *XL50-2MC-3-TG Top Glass *XL50-2MC-21-SS Small Spacer *XL50-2MC-39-TUP Touch Up Pen *XL50-2MC-4-GS Glass Shelf *XL50-2MC-22-M4M5FW M4/M5 Flat Washer (for TV mounting) *XL50-2MC-40-CH Complete Hardware *XL50-2MC-5-LL Left Leg *XL50-2MC-23-M6M8FW M6/M8 Flat Washer (for TV mounting) *XL50-2MC-41-RPG Round Plastic Grommet *XL50-2MC-6-RL Right Leg *XL50-2MC-24-M4LW M4 Lock Washer *XL50-2MC-42-OPG Oval Plastic Grommet *XL50-2MC-7-MF Mounting Frame *XL50-2MC-25-M5LW M5 Lock Washer *XL50-2MC-43-SB Safety Bar *XL50-2MC-8-PC Plastic Cover *XL50-2MC-26-M6LW M6 Lock Washer *XL50-2MC-44-TSF Top Shelf Frame *XL50-2MC-9-MB Monitor Bracket *XL50-2MC-27-M8LW M8 Lock Washer *XL50-2MC-45-MSF Middle Shelf Frame *XL50-2MC-10-3/4B 3/4” Bolt *XL50-2MC-28-M4x12B M4 x 12 Bolt *XL50-2MC-46-BSF Bottom Shelf Frame *XL50-2MC-11-1 1/4B 1 1/4” Bolt *XL50-2MC-29-M4x30B M4 x 30 Bolt *XL50-2MC-47-SB Swiveling Bracket *XL50-2MC-12-FW Flat Washer *XL50-2MC-30-M5x12B M5 X 12 Bolt *XL50-2MC-48-FL Floor Leveler *XL50-2MC-13-LFW Large Flat Washer *XL50-2MC-31-M5x30B M5 x 30 Bolt *XL50-2MC-49-FLS Front Left Support *XL50-2MC-14- LW Lock Washer *XL50-2MC-32-M6x12B M6 x 12 Bolt *XL50-2MC-50-FRS Front Right Support *XL50-2MC-15-SC Suction Cup *XL50-2MC-33-M6x35B M6 x 35 Bolt *XL50-2MC-51-BLS Back Left Support *XL50-2MC-16-N Nut *XL50-2MC-34-M8x16B M8 X 16 Bolt *XL50-2MC-52-BRS Back Right Support *XL50-2MC-17-AW Allen Wrench *XL50-2MC-35-M8x40B M8 x 40 Bolt *XL50-2MC-53-WFR Wooden Front Rail *XL50-2MC-18-OW Open Wrench *XL50-2MC-36-2 1/2LB 2 1/2” Lag Bolt