VAS XL50-5GB User manual

Model # XL50-5GB
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 1
50”3-in-1 Console
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this item
to the Retailer Store. Please call our toll free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.whalenfurniture.com EMAIL: [email protected]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
LOT No.:
DATE OF PURCHASE:
XL50-5GB

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 2
QUALITY GUARANTEE
We are confident that you will be delighted with your VAS Furniture purchase.
Should this product be defective in workmanship or materials or fail under
normal use, we will repair or replace it for up to 1 year from date of purchase.
Every VAS Furniture product is designed to meet your highest expectations.
We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST Monday to Friday
www.whalenfurniture.com
MANUFACTURER: VAS FURNITURE
CATALOG: 50”3-in-1 Console (XL50-5GB)
DATE OF MANUFACTURE: September 2009
MADE IN CHINA
FITS UP TO MOST 56”FLAT PANEL TV’S
MAXIMUM LOAD 135 LBS
MAXIMUM LOAD 50 LBS
This unit is intended for use only with the products and maximum
weights indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury. The base of the television must
be placed squarely in the center of the stand with no overhanging on either side.

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 3
Parts & Hardware List for Table-top
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
A-Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)
D1- Short Spine (1) E- Left Leg (1) F- Right Leg (1)
G- Top Glass (1) H- Middle Glass Shelf (1) I- Bottom Glass Shelf (1)
(1)- Suction Cup (2)- 3/4” Bolt (3)- 1 1/4” Bolt (5)- Lock Washer
(16+1 extra) (14+1 extra) (6+1 extra) (20+1 extra)
(6)- Flat Washer (7)- Glass Raiser Allen Wrench Tipping Restraint Hardware Kit (1)
(20+1 extra) (8) (1) (Inside Plastic Bag)
Tools Required: Allen Wrench (provided).

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 4
Parts & Hardware List for Universal Wall Mount only
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
K- XYZ Mounting Frame (1) L- Monitor Bracket (2) M- Safety Bar (1)
(8) - 1 3/4” Concrete Anchor (9) - Large Flat Washer (10) - 2 1/2” Lag Bolt
(6pcs) (6pcs) (6pcs)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)
M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Note: Please keep the rest of the hardware & parts for future use.
Tools Required: Phillips Screwdriver, Mallet, Power Drill, 3/16” Drill Bit, Socket wrench adapter
with socket set, 1/2” Masonry Bit for brick or concrete, Level and Stud Finder.

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 5
Assembly Instructions for Table-top
Note: Please do not fully tighten all bolts until you finish assembling all parts, then go
back and fully tighten all bolts, this will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Locate Short Spine (D1) and set back face down on a scratch free surface as shown in
detail #1.
3. Align the holes on “U”shape plate of three Shelf Frames (A, B & C) with the threaded
inserts on the Short Spine (D1) in place, insert and screw 3/4”Bolts (2) through Lock
Washers & Flat Washers (5 & 6) through the bracket holes into the Spine. See detail #1.
Required hardware in this step
No.
2
5
6
Sketch
Description
3/4”Bolt
Lock Washer
Flat Washer
Qty.
10pcs
10pcs
10pcs
Tools required
Allen Wrench

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 6
Assembly Instructions for Table-top
4. Stand the unit upright.
5. Pick up Left Leg (E) and attach to the Middle & Bottom Shelf Frame (B & C) by inserting the
1 1/4” Bolts (3) with Washers (5 & 6) from inside the shelf frame through the pre-drilled
holes on side rail into the threaded inserts on Leg. See detail #2. DO NOT tighten the bolts.
6. Proceed to attach the Left Leg (E) to Top Shelf Frame (A) using two 3/4”Bolts (2) with
Washers (5 & 6) through the end bracket into the Leg. See detail #2A.
7. Repeat last two steps to install Right Leg (F) at the other end.
Required hardware in this step
No.
2
3
5
6
Sketch
Description
3/4”Bolt
1 1/4”Bolt
Lock Washer
Flat Washer
Qty.
4pcs
6pcs
10pcs
10pcs
Tools required
Allen Wrench

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 7
Assembly Instructions for Table-top
8. Go back and tighten all bolts with Allen Wrench provided.
9. In case of uneven floor, Floor Levelers are provided at the bottom of both Legs (E & F).
Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in
detail #3.
Parts Provided Tools Required
Pre-attached Floor Leveler No Tool Required

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 8
Assembly Instructions for Table-top
10.Put the Suction Cups (1) firmly into top holes of the Middle Shelf Frame (B) & Bottom Shelf
Frame (C) as shown in detail #4.
11.Screw the Glass Raisers (7) onto the top holes of Top Shelf Frame (A), make sure they go all
the way in. See detail #4.
12.Place the Top Glass (G) & Glass Shelves (H & I) in place as shown in detail #4. Push each
glass all the way back against the Spine. Make sure the glass sits correctly and is properly
centered. Also, be sure to press down evenly and firmly each shelf onto the Suction Cups to
make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the
glass shelf from falling and getting damage. If glass is scratched you can minimize the
damage by using a BLACK marker and filling in scratched area from underneath.
Required hardware in this step
No.
1
7
Sketch
Description
Suction Cup
Glass Raiser
Qty.
16pcs
8pcs
Tools required
No tool required

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 9
Assembly Instructions for Table-top
13.Position the assembled Table Top in your desired location against the wall. Now follow the
instructions printed on the white plastic bag in order to mount the Tipping Restraint Hardware
Kit to the Spine properly. As shown in detail #5.
NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO
THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
14.The Table Top is ready for use now. Be sure to position your TV in center of console with no
overhang on either side.

Model # XL50-5GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 10
Assembly Instructions for Universal Wall Mount
Installing XYZ Mounting Frame onto WOODEN WALL
15.The XYZ Mounting Frame (K) must be mounted to two Wood Studs at least 12” apart, using
a high quality Stud Finder to locate the two adjacent studs. After you have located the studs,
verify with a nail for added security. See detail #6A.
16.Pre-drill a 2 1/2" deep hole at the desired height in each stud using a 3/16” drill bit, make
sure that the holes are centered in the studs and level with each other. Use the XYZ
Mounting Frame (K) as a template to mark the corresponding location for the bottom holes
in each stud, drill holes 2 1/2" deep with the 3/16” drill bit at the marked location.
17.Orient the Mounting Frame with the “C” plate against the wall, and using four Lag Bolts (10)
with Large Flat Washer (9) through the slots of “C” Plate on Mounting Frame into the holes
in the wall, secure the mounting frame to the wall as shown in detail #6B.
Required hardware in this step
No.
9
10
Sketch
Description
Large Flat Washer
2 1/2” Lag Bolt
Qty.
4pcs
4pcs
Tools required
Stud Finder, Mallet, Power Drill, 3/16” Drill Bit, Socket Wrench
Adapter with Sock Set, and Level.
Do not over tighten the Lag Bolts. Tighten Lag Bolts only until the Lag
Bolt Washer is pulled firmly against the “C”Plate of Mounting Frame. If there is a layer of
drywall or other material, this drywall or other material may not exceed 5/8 inch in
thickness. Failure to heed this caution may result property damage and/or personal injury.