VAT 670 Series Assembly instructions

Installation, Operating &
Maintenance Instructions
899078EA Edition 2017-10-11
Symmetrical flow control & isolation valve
Series 670
DN 320 mm (I. D. 12" )
This manual is valid for the following product ordering number
67050-PH52-ABR2

Series
670
2/31 Edition 2017-10-11 899078EA
Imprint
Manufacturer
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Website:
Phone:
Fax:
Email:
www.vatvalve.com
[phone]
[phone]
[email protected]
Publisher
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Editor
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Print
VAT Vakuumventile AG, CH
-
9469 Haag, Switzerland
Copyright
©
VAT Vakuumventile AG
2017
No part of these Instructions may be reproduced in any way (photocopies,
microfilms or any other reproduction processes) nor may it be manipulated with
electronic systems, duplicated or distributed without written permission from VAT.
Offenders are liable to pay damages.
The original VAT firmware and updated state of the art versions of the VAT
firmware are intended for use with VAT products. The VAT firmware contains a
limited, time unlimited user license. The VAT firmware may not be used for
purposes other than those intended nor is it permitted to make copies of the VAT
firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to
other people.
The use of trade names, brand names, trademarks, etc. in these Instructions
does not entitle third parties to consider these names to be unprotected and to
use them freely. This is in accordance with the meaning of the laws and acts
covering brand names and trademarks.

Series 670
899078EA Edition 2017-10-11 3/
31
Contents
1 Description of product........................................................................4
1.1 Identification of product ...................................................................................................4
1.2 Use of product.................................................................................................................4
1.3 Used abbreviations..........................................................................................................4
1.4 Related documents..........................................................................................................4
1.5 Important information.......................................................................................................4
1.6 Technical data.................................................................................................................5
1.6.1 Valve unit ............................................................................................................5
2 Safety ...................................................................................................6
2.1 Compulsory reading material...........................................................................................6
2.2 Danger levels ..................................................................................................................6
2.3 Personnel qualifications...................................................................................................7
2.4 Safety labels....................................................................................................................7
3 Design and Function...........................................................................8
3.1 Design.............................................................................................................................8
3.2 Function...........................................................................................................................8
4 Installation...........................................................................................9
4.1 Unpacking .......................................................................................................................9
4.2 Installation into the system............................................................................................11
4.2.1 Installation space condition...............................................................................12
4.2.2 Installation overview..........................................................................................13
4.2.3 Installation procedure........................................................................................14
4.3 Tightening torque ..........................................................................................................15
4.4 Admissible forces..........................................................................................................15
5 Operation...........................................................................................16
6 Trouble shooting...............................................................................17
7 Maintenance ......................................................................................18
7.1 Maintenance intervals....................................................................................................19
7.2 Maintenance procedure.................................................................................................19
7.2.1 Removing the plate and plate seal replacement ...............................................20
8 Repairs...............................................................................................23
9 Dismounting and Storage.................................................................24
9.1 Dismounting ..................................................................................................................24
9.2 Storage..........................................................................................................................25
10 Packaging and Transport.................................................................26
10.1 Packaging......................................................................................................................26
10.2 Transport.......................................................................................................................27
11 Disposal.............................................................................................28
12 Spare parts ........................................................................................29
13 Appendix............................................................................................30

DESCRIPTION OF PRODUCT Series
670
4/31 Edition 2017-10-11 899078EA
1 Description of product
1.1 Identification of product
The fabrication number and order fabrication are fixed on the product directly or by means of an
identification plate.
Fabrication No.:
000 . .- . . . .- . . . ./ . . . .
A - . . . . . .


Fabrication number
Order number
1.2 Use of product
Use product for clean and dry vacuum applications only. Other applications are only allowed with the
written permission of VAT.
1.3 Used abbreviations
Abbreviation Description
SFV Symmetrical flow valve
CPA Control performance analyser
1.4 Related documents
• Product data sheet
• Dimensional drawing
• External controller manual (846473EA)
1.5 Important information
This symbol points to a very important statement that requires particular attention.
Example
:
VAT disclaims any liability for damages resulting from inappropriate packaging.

Series 670 DESCRIPTION OF PRODUCT
899078EA Edition 2017-10-11 5/
31
1.6 Technical data
1.6.1 Valve unit
Describtion
Symmetrical flow functional principle (given)
Pressure range at 20 °C 1 × 10E-6 mbar to 1.2 bar (abs)
Leak rate to outside at 20 °C 1 × 10E-5 mbar l/s
Leak rate valve seat at 20 °C 1 × 10E-4 mbar l/s
Max. differential pressure on plate at isolation 1200 mbar (from chamber side)
10 mbar (from pump side)
Max. differential pressure on plate during operation 10 mbar
Cycles (under vacuum) until first service
- Isolation cycles (open - closed - open)
- Throttling cycles (open - max. throttle - open)
200’000 (unheated and under clean conditions)
2’000’000 (unheated and under clean conditions)
Admissible operating temperature 10 °C to +120 °C
Mounting position Horizontal (actuators downwards)
Process side
materials flange Aluminum EN AW-6082 T651 (3.2315.72) hard anodized
plate Aluminum EN AW-6082 T651 (3.2315.72) hard anodized
actuator shafts Stainless steel 316L (1.4435 or 1.4404)
bellows Stainless steel 633 (AM350)
bolts stainless steel A2 (304)
Seals plate seal FKM (Viton
®
)
actuator shaft seals FKM (Viton
®
)
flange seal FKM (Viton
®
)
Max. controllable conductance (N
2
molecular flow) 30’000 l/s (max. 130 mm stroke)
Min. controllable conductance (N
2
molecular flow) 0.3 l/s
Actuating time full open to closed (throttling) typ. 1.0 s per 100mm
closed (throttling) to full open typ. 1.0 s per 100mm
full open to closed (isolated) typ. 1.0 s
closed (isolated) to full open typ. 1.0 s
Stroke mechanical maximum 130 mm
effective According to controller configuration, refer to product data
sheet of respective controller
Weight Approx. 31 kg
Dimensions Refer to dimensional drawing (available on request)

SAFETY Series
670
6/31 Edition 2017-10-11 899078EA
2 Safety
2.1 Compulsory reading material
Read this chapter prior to performing any work with or on the product. It contains important information
that is significant for your own personal safety. This chapter must have been read and understood by
all persons who perform any kind of work with or on the product during any stage of its serviceable
life.
NOTICE
Lack of knowledge
Failing to read this manual may result in property damage.
Firstly, read manual.
These Installation, Operating & Maintenance Instructions are an integral part of a
comprehensive documentation belonging to a complete technical system. They must
be stored together with the other documentation and accessible for anybody who is
authorized to work with the system at any time.
2.2 Danger levels
DANGER
High risk
Indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
Medium risk
Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
Low risk
Indicates a hazardous situation which, if not avoided, may result in minor or moderate
injury.
NOTICE
Command
Indicates a hazardous situation which, if not avoided, may result in property damage.

Series 670 SAFETY
899078EA Edition 2017-10-11 7/
31
2.3 Personnel qualifications
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
2.4 Safety labels
Label Part No. Location on valve
T-9001-156 On protective foil covering the
valve opening

DESIGN AND FUNCTION Series
670
8/31 Edition 2017-10-11 899078EA
3 Design and Function
3.1 Design
1 Flange seal 6 Intermediate piece
2 Plate screw 7 Actuator shaft with bellows
3 Plate 8 Actuator (stepper motor)
4 Plate seal Valve seat side
5 Flange
3.2 Function
The valve plate (3) acts as a throttling element and varies the conductance of the valve opening. The
controller calculates the required plate position to achieve the set point pressure. Actuation is
performed by two synchronous stepper motors (8). Encoders monitor the position. This principle
ensures fast and accurate process pressure control.
3
6
2
4
1
5
8
7

Series 670 INSTALLATION
899078EA Edition 2017-10-11 9/
31
4 Installation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
4.1 Unpacking
WARNING
Heavy weight
Physical overstraining.
Use a crane to lift valves DN 200 (8”) and larger.
NOTICE
Physical overstraining at actuators
Inappropriate handling with the valve may cause in damage of actuator.
Do not place the valve on the actuators.
• Make sure that the supplied products are in accordance with your order.
• Inspect the quality of the supplied products visually. If it does not meet your
requirements, please contact VAT immediately.
• Store the original packaging material. It may be useful if products must be returned
to VAT.

INSTALLATION Series
670
10/31 Edition 2017-10-11 899078EA
1. Open the transport case and remove inside packing material as far as necessary.
2. Use a crane and lifting attachments (4 × M10 thru) to lift the valve. See example figure below.
3. Lift the valve carefully and place it on a clean place.
Do not remove protective foils from valve opening

Series 670 INSTALLATION
899078EA Edition 2017-10-11 11/
31
4.2 Installation into the system
CAUTION
Valve opening
Risk of injury.
Do not connect the controller to power before the valve is installed complete into the
system.
NOTICE
Wrong connection
Wrong connection may result in damage of controller or power supply.
Connect all cables exactly as shown in the following schematic.
NOTICE
Burned connector pins (spark)
Connector pins or electronic parts could damage, if plugged and unplugged under
power.
Do not plug or unplug connectors under power.
NOTICE
Contamination
Gate and other parts of the valve must be protected against contamination.
Always wear clean room gloves when handling the valve.
• Make sure that the sealing surfaces of the valve and the chamber are undamaged.
• Mount valve to a clean system only.

INSTALLATION Series
670
12/31 Edition 2017-10-11 899078EA
4.2.1 Installation space condition
Install the valve with actuators with space for dismantling and air circulation as shown
in figure below.

Series 670 INSTALLATION
899078EA Edition 2017-10-11 13/
31
4.2.2 Installation overview
Sample picture
Chamber
External Controller (3)
Pump side
Symmetrical flow valve [1]
Actuator cables [2]

INSTALLATION Series
670
14/31 Edition 2017-10-11 899078EA
4.2.3 Installation procedure
All numbers in brackets refer to chapter «Installation overview».
1. Remove protective covers from body flanges.
2. Install symmetrical flow valve [1] into the vacuum system. Refer to chapter «Installation
overview».
• Do not tighten the flange screws stronger than indicated under «Tightening
torque».
• Do not admit higher forces to the valve than indicated under «Admissible forces».
• Make sure that enough space is kept free to do preventive maintenance work. The
required space is indicated on the dimensional drawing
3. Install actuator cables [2] to actuators and then to the External Controller [3]. Refer to chapter
«Installation overview».
4. Install all electrical connections at External Controller. Refer to «External Controller manual»
846473EA
5. This valve may optionally be equipped with a heating device. Connect VAT heating device
according to manual of respective heating device.

Series 670 INSTALLATION
899078EA Edition 2017-10-11 15/
31
4.3 Tightening torque
NOTICE
Physical overstraining at valve flange.
Physical overstraining may cause in damage of valve flange.
Do force (fasten) the screws more as specified by the screw manufacturer.
4.4 Admissible forces
Forces from evacuating the system, from the weight of other components, and from
baking can lead to deformation and malfunctioning of the valve. Stress has to be
relieved by suitable means, e.g. bellows sections.
Axial tensile or
compressive force
«F
A
» Bending mo ment «M»
N lb. Nm lbf.
4000 880 160 120
For a combination of both forces (F
A
and M) the values are invalid.
Verify that the depth of the mounting screws is min. 1x thread diameter.
Please contact VAT for more information.
M
FA

OPERATION Series
670
16/31 Edition 2017-10-11 899078EA
5 Operation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
CAUTION
Valve opening
Risk of injury.
Do not operating before the valve is installed complete into system.
For «Operation» refer to «External Controller manual» 846473EA.

Series 670 TROUBLE SHOOTING
899078EA Edition 2017-10-11 17/
31
6 Trouble shooting
For «Trouble shooting » refer to «External Controller manual» 846473EA.
If you need any further information, please contact one of our service centers. You can find the
addresses on our website: www.vatvalve.com.

MAINTENANCE Series
670
18/31 Edition 2017-10-11 899078EA
7 Maintenance
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
CAUTION
Hot surfaces
Heated valve may result in minor or moderate injury.
Do not touch valve and heating device during operation. Once heating is switched off
(valve and system) await until the valve is cooled down complete before doing any
work.
CAUTION
Valve opening
Risk of injury.
Human body parts must be kept out of the valve opening and away from moving parts.
NOTICE
Contamination
Gate and other parts of the valve could be contaminated.
Always wear cleanroom gloves when handling the valve.
NOTICE
Scratches on sealing surface
Scratches on sealing surface cause in malfunction (leak) of valve
Only qualified personnel are allowed to carry out the described work.

Series 670 MAINTENANCE
899078EA Edition 2017-10-11 19/
31
7.1 Maintenance intervals
Under clean operating conditions, the valve does not require any maintenance during the specified
cycle life. Contamination from the process may influence the function and requires more frequent
maintenance.
Before carrying out any maintenance, please contact VAT. It has to be individually decided whether
the maintenance can be performed by the customer or has to be carried out by VAT
www.vatvalve.com. The fabrication number on the valve has always to be specified. Refer to chapter
«1.1 Identification of product» for fabrication number.
7.2 Maintenance procedure
• Open / close the service cover and valve cleaning. Refer to manual of customized process
chamber.
This task is described on customer side.
• Removing the plate and plate seal replacement. Refer to chapter «7.2.1 Removing the plate and
plate seal replacement».

MAINTENANCE Series
670
20/31 Edition 2017-10-11 899078EA
7.2.1 Removing the plate and plate seal replacement
7.2.1.1 Required tools
• Allen wrench 5 mm
• O-ring removal tool
• CPA
• Cleanroom wiper
• Isopropyl alcohol
• Clean room gloves
Electrical power is required.
Description Required tool
1. Open the service cover. Refer to
manual of customized process
chamber.
Use the «CPA» or «Service Box 2» This
example is with «CPA». The valve is
closed and controller is powered.
Default position resolution is [0-100000].
2. Go to [LOCAL] mode.
CPA
3. Select position [10’000] = 10 %
open.
4. Switch OFF the power supply to
external controller
CPA
5. Disable the PFO CPA
6. Switch OFF the power supply