Vax SCSMV1SG User manual

Steam
MULTIFUNCTION STEAMER
S85-CM
SCSMV1SG
LET’S GET STARTED.

Basic
safety
precautions
Don’ts
Do’s
This STEAMER is intended for household use only and NOT
for commercial or industrial use.
CAUTION: Danger of scalding
• Only use the steamer indoors and keep the area you’re
cleaning well lit.
• Keep ngers, hair and loose clothing away from moving parts
and openings whilst using the steamer.
• This steamer can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the steamer. Cleaning and user maintenance
shall not be performed by children without supervision.
• Please refer to oor manufacturer’s care recommendations before use, and
test your ooring/carpet/rugs by running the steamer over a small hidden
area, if no pile distortion or no damage occurs continue cleaning. Not suitable
for use on wax polished oors or furniture, acrylic surfaces and synthetic,
velvet or steam/water sensitive materials.
• This steamer should not be used to clean electrical appliances such as
microwaves, televisions and electrical heating systems etc.
• Only Vax recommended cloths and accessories should be used with
this steamer. This steamer is a water only product, using detergents will
invalidate the guarantee.
• Don’t touch any hot areas/accessories on your steamer.
It’s normal for the steamer and accessories to heat up during
use, always allow them to cool down before handling.
• Don’t use the steamer if it has been dropped, damaged,
immersed in water or left outdoors.
• Don’t run over the power cord or use steamer if the power
cord or plug is damaged. Please contact our Customer Care
Line on 0330 026 8455 (Mon-Fri 8:30am to 6:30pm
Sat 9:00am to 5:00pm).
• Don’t handle the plug or use the steamer with wet hands.
Don’t pull or carry the steamer by the power cord.
• Don’t use the power cord as a handle, don’t pull the power cord around
corners or sharp edges or close a door over the power cord. Don’t unplug
the steamer by pulling on the power cord.
• Don’t attempt to remove blockages with sharp objects as this may cause
damage to the steamer, remove blockages only as instructed in this guide.
• Don’t aim the steamer at people, animals, plants and electrical components
or wires. Never touch the steam jet (there is a risk of scalding).
• Don’t use the steamer with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Don’t use the steamer to clean or refresh any items of clothing that are still
being worn on the body.
• Don’t leave the steamer turned on when unattended.
• Always ll the water tank with water only. Never add perfume,
stain remover or products containing alcohol. Filling the water
tank with hot or boiling water will damage the steamer and
invalidate the guarantee.
• Always vacuum your carpets thoroughly and ensure hard oor
areas are free from grit and debris before using your steamer.
• Always unplug the steamer and allow to cool before carrying
out any maintenance.
• Turn o all controls on the steamer before disconnecting or
connecting the power cord, after use always wrap the power
cord around the cord clips.
• Take extra care when cleaning on the stairs.
• Always replace the fuse in the plug with a British 13amp fuse. Always protect
the power cord from heated surfaces and open ames.
• Use only CE approved 13amp extension cords, non-approved extension cords
can overheat. Care should be taken to arrange the extension cord as it could
be a trip hazard.
• Store the steamer in a cool, dry area away from children. Before storing the
steamer please make sure the water tank is thouroughly clean and empty.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.
Let’s talk safety

Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Accessories
Notes
Carpet Glider
Grout Brush
Small Round Brush
Squeegee
Measuring Jug
Concentration Nozzle
Microbre Pad
Utility Head Pad
Utility Head
Steam Clean Multi
and Steam Glide
Included with
your machine
Thank you for buying this Steam product
Taking care of your sealed hard oors and surfaces
Vax Steam products are designed to make steam cleaning your hard oors and surfaces
regularly, as eective and ecient as possible, and this user guide will help you get the most
out of your machine.
Maintaining your hard oors and surfaces with our Steam products will ensure they
keep looking beautiful and are hygienically clean.
Taking care of your Multifunction Steamer
Also inside this guide are instructions on maintaining your new machine, so that
it’s always ready when you are to tackle your hard oors and surfaces.
Contents
Let us know what you think @VaxUK
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support

Push the main body down into the
oorhead until it clicks into place.
Stand the steamer upright by pushing the
main body forward to lock into position.
Push the handle into main body until it
clicks into place. The collar should be gripped
when connecting or releasing the handle.
Assembling your steamer
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
CAUTION
• The steamer and accessories get very hot during use, always allow them to cool down before handling.
• Always unplug and switch o the steamer when assembling or disassembling.
• Always switch o the steamer before emptying the water tank or changing the cloths/accessories.
IMPORTANT
• Please refer to oor manufacturer’s care recommendations before use and test the steamer on a hidden area of ooring
to begin with.
• Test for colour fastness in a small hidden area of upholstery/fabric to check for colour removal before use.
• When using the steamer, basic safety precautions should always be observed.
• Don’t aim the steamer at people, animals, plants and electrical components or wires. Never touch the steam jet or oorhead
from a short distance (there is a risk of scalding).
• The steamer is equipped with a thermostat and a thermal cut-out. If for any reason the steamer overheats it will switch o.
If this happens turn o and unplug the steamer, allow to cool for at least 2 to 4 hours and re-try.
• Don’t use hot or boiling water to ll or clean water tank.
Handheld steam trigger (hidden)
Handle
Handheld handle
Subject to technical change without notice. *To purchase consumables and accessories, please visit vax.co.uk
Handle release button
On / o & steam control dial
Floorhead
Quick release cord hook
Accessory oorhead
release button
Power on indicator
Water tank cap
Water tank (Part of unit)
Carpet Glider
Quick release cord hook
Getting to know your machine
Technical Specication
Microbre Pads (Type 1)
1-1-131448-00
Pro Cleaning Pads (Type 6)
1-1-132319-01
Coral Cleaning Pads (Type 3)
1-1-131643-00
Carpet Glider (Type 3)
1-1-133527-00
Accessories & Consumables
Getting started
Name Steam Clean Multi S85-CM
Voltage 220-240v˜50Hz
Wattage 1300w
Cord length 5m
Weight 2.5kg
Name Steam Glide SCSMV1SG
Voltage 220-240v˜50Hz
Wattage 1300w
Cord length 5m
Weight 2.5kg
Before you Begin

IMPORTANT: When using on carpets, always make sure the Microbre Pad is used and covers the oorhead entirely before
using the Carpet Glider. Only use the Carpet Glider when refreshing carpets.
Place the Microbre Pad on
the oor white side facing
up. Place steamer onto pad
making sure the entire pad
covers the oorhead.
Twist the steam control dial
to desired setting.
With Microbre Pad
attached, push steamer
into front of the Carpet
Glider, then place back
of the oorhead into the
clip. The Carpet Glider
should only be used
when refreshing carpets.
Plug into mains, turn dial to
‘ON’ position, the red light will
illuminate to indicate power on.
There will be no sounds for
the rst 30 seconds whilst it is
heating up.
Place your foot on
oorhead and pull handle
backwards to recline.
Refreshing carpets
Move the steamer slowly
backwards and forwards
across the carpet paying
particular attention to high
trac areas.
To release the Carpet Glider,
place your foot on clip and
push down. Lift steamer
to remove.
Steam is activated automatically.
Take care when changing
settings during cleaning.
Remove oorhead and handle
and place steamer on at
surface. Twist water tank
cap anticlockwise and lift
to remove.
Correct
Incorrect
Do not ll directly from tap
or over sink. Keep steamer
on at surface. Use the
Measuring Jug and ll the
tank with 330ml (2 x 165ml)
of water.
Replace cap, align tabs
and twist clockwise
to tighten.
IMPORTANT
• Never turn the steamer over when water is in the tank, as some water may leak through the air valve.
It is normal for the water tube to make a rattling sound inside the water tank during use.
Filling water tank
Cleaning hard oors
Place the Microbre Pad on the
oor white side facing up. Place the
oorhead onto Microbre Pad making
sure the Microbre Pad covers the
entire oorhead.
Plug into mains, turn dial to ‘ON’; the red
light will illuminate to indicate power on. The
steamer will be ready after approximately 30
seconds. There will be no sounds for the rst
30 seconds whilst it is heating up.
To steam your oors twist the steam
control dial to desired setting. Steam
is activated automatically. Take
care when changing settings
during cleaning.
Place foot onto the oorhead and
pull handle backwards to recline.
Turn dial to ‘OFF’ position and allow
steamer to cool, the amber light will
switch o. Hold corner of pad down with
your foot and lift steamer to peel away.
IMPORTANT
• Never use the steamer without a Microbre Pad attached to the oorhead.
• Never leave the steamer on one spot for an extended period of time or with a damp or wet Microbre Pad attached as this
may damage the oor surface.
Move the steamer slowly backwards
and forwards across the oor paying
particular attention to high trac areas.
Using your machine Using your machine
Switch OFF and allow
to cool rst. Steam is
automatic in stick
mop mode.
CAUTION
TIP
The water tank cap
has lock and unlock
padlock symbols.

CAUTION: Never use the Squeegee on cold glass/windows as it may cause damage.
Stretch utility pad over
Utility Head.
Push Utility Head and pad into steamer until
secure. It will not lock into place. Pull test
to check it is secure.
Small tools can be attached via the
Concentration Nozzle. Push together to
click into position and secure. Push hard
and ensure click is heard. Add pull test on
brushes to check tools are secure.
Push Utility Head and Squeegee into steamer until
secure. It will not lock into place but should sit rmly
against steamer.
Attaching accessories
Attaching brushes Attaching Utility Head
Attaching Squeegee
Align the tab on the Squeegee with the Utility
Head and utility pad, push together to lock into
position. Please note that the utility pad must
be attached to the Utility Head before the
Squeegee can be tted on. Squeegee will
not connect without the pad on rst.
To remove, pull Squeegee
down on tab.
Using the machine as a handheld
IMPORTANT: The handheld is to be used with water only, putting detergent into the water tank can cause damage.
Always check the tools are clean and free from debris, don’t use if damaged, broken or worn.
Push handle release button and lift
handle to remove. The collar should be
gripped with one hand when releasing
the handle with the other hand.
Push Concentration Nozzle into steamer
until it clicks into place.
Press accessory release button and lift
steamer to release oorhead.
Plug into mains, turn the dial to ‘on’
position. The red light will illuminate to
indicate power on.
To produce steam squeeze the trigger in short bursts. Don’t hold the trigger
continuously to prevent over wetting. Allow 30 seconds for steamer to
warm up. No sound will be heard until trigger is pressed. No steam will be
visible until after 30 seconds.
Twist the steam control dial to
desired setting.
Using your machine Using your machine
TIP
After attaching your
chosen accessory
gently pull to make
sure it’s locked into
place or feels secure.
Always switch OFF the
steamer before attaching
the concentration tool
and accessories.
CAUTION

Unplug, remove oorhead and handle place
steamer on at surface. Twist water tank
cap anticlockwise and lift to remove.
Emptying the water tank
Empty any excess water
over an empty sink.
IMPORTANT: Don’t use bleach or fabric softener when washing the Microbre Pad. Always allow the steamer
to fully cool down before removing the Microbre Pad.
IMPORTANT: Never remove the water tank cap with the product upright as water could leak out–always remove the oorhead
and handle and place on a at surface before removing the water tank cap.
The Microbre/Utility Head Pad are machine
washable (Max 40⁰C) allow to fully dry
before use. Utility Head Pad is hand wash only.
Cleaning the Microbre/Utility Head Pad
MAX
40˚C
24hr
IMPORTANT: Taps should be turned o when steaming around them. Don’t steam clean ovens, oven surfaces or grills when
hot, allow to cool to room temperature rst.
Ideal for any surface from tiles, sinks,
toilets and oven tops.
Use to remove soap scum in baths and
shower enclosures and to clean heavily
soiled areas in kitchens.
Using the accessories
Lifts embedded dirt from inbetween tiles.
Attach utility pad to Utility Head
for use on upholstery and clothes.
Do not use detergent on fabrics
and upholstery.
Great for leaving your windows, tiles
and mirrors gleaming.
Concentration Nozzle Small brush Grout Brush
Utility Head and pad Squeegee
Test for colour fastness in
a small hidden area of
upholstery/fabric to check
for colour removal
before use.
Ensure steamer
is unpluged before
emptying water tank.
CAUTION CAUTION
Using your machine Taking care of your machine

Clearing blockages
IMPORTANT: Turn dial on steamer to ‘OFF’ position, switch o at mains and unplug safely.
Allow to fully cool down before performing maintenance or troubleshooting checks.
Use a small thin object such as a
paperclip to insert into the nozzle and
clear any blockage.
To clear a blockage in the oorhead,
remove the Microbre Pad from the
oorhead, insert a small thin object,
such as a paperclip, into the steam
holes to remove any blockage.
Push the accessory oorhead
release button and lift the main
body from the oorhead to remove.
Also remove the handle.
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
2x Microbre Pads (Type 1)
1-1-131448-00
Microbre Pads, ideal to remove dirt and grime. These
cleaning pads attach to the base of the steamer so it’s
quick and easy to t and remove.
Pro Cleaning Pads (Type 6)
1-1-132319-00
3x pro cleaning pads. Ideal for stubborn stain
removal throughout your home. These cleaning
pads attach to the base of the steamer
so it’s quick and easy to t and remove.
Steam Mop Cleaning Pads
1-1-131864-00
2x Microbre Pads, ideal to
remove dirt and grime.
2x coral cleaning pads for your steamer.
Super absorbent and ideal for removing stubborn stains.
Total Home
1-1-132528-00
8x Microbre Pads. Avoid cross contamination between
dierent areas of your home with this Total Home Cleaning
Kit. Kit contains 8 x coloured Microbre Pads for all areas of
your home. Kit also contains a free wash bag worth £9.99.
3x Microbre Pads (Type 2)
1-1-133071-00
3 washable Microbre Pads for everyday hard oor
cleaning. Drawstring attachment ideal for everyday
cleaning. Washing machine washable for continuous
use.
Coral Cleaning Pad Kit (Type 3)
1-1-131643-00
2 coral cleaning pads – super absorbent washable
pads, ideal for subborn stains and cleaning uneven
surfaced such as slate.
Let’s talk technical Accessories

CAUTION: Always unplug the steamer before performing maintenance/troubleshooting checks.
What to do if it goes wrong
• Check the ‘This pack contains’ panel on the box to make sure the part
is included with your steamer.
• Check the on/o control dial position.
• Check the amber light is illuminated.
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace with
a British 13amp fuse.
• The Microbre Pad may already be saturated or dirty. Wash the
Microbre Pad, go to ‘Taking care of your machine’.
• There may be no water in water tank, check the water tank has water.
• Check the water tank cap is securely tted onto the water tank.
• The water may not yet be at temperature . The steamer will take approximately
30 seconds to heat up.
• Steam path may be blocked. Go to ‘Let’s talk technical’.
• Check steam control dial has been turned to ‘on’.
• Water tank level may be low, rell with water.
• If using as a stick mop - handle may not be fully inserted. Release handle,
press handheld trigger to check steam is working. Re-insert handle until
it clicks into place.
SolutionProblem
Is there an
accessory missing?
The steamer has
no power.
Why is the steamer
not producing steam?
Why won’t the Microbre
pad pick up dirt?
†
†Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
Getting in touch

NotesNotes

GET IN TOUCH
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
S85-CM and SCSMV1SG are manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage
Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2016 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
This manual suits for next models
1
Table of contents
Other Vax Steam Cleaner manuals

Vax
Vax Steam Fresh Pro User manual

Vax
Vax VCSD-03 User manual

Vax
Vax S86-SF-A User manual

Vax
Vax V-081 SERIES User manual

Vax
Vax SteamFresh Multi S85-SF-M Installation instructions

Vax
Vax S5-CM User manual

Vax
Vax Steam Grime Master User manual

Vax
Vax Duet Master S7-A+ User manual

Vax
Vax VS102 User manual

Vax
Vax S2 Series User manual