Vaxcel T0040 Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0040
1. Thread two headless screws to the mounting plate, and secure them with four lock nuts (two on each side of
the mounting plate). Adjust the length of the headless screws if necessary.
2. Attach the mounting plate to the outlet box by using two mounting screws.
3. Install bulbs from the front of the metal frame (not included). See relamping label at socket area or packaging
for maximum allowed wattage. (See Fig.1)
Glass Panel
Fig.2
Metal Frame
Fixture
Glass Panel (H)
Bulb Type A Max.100W
(not included)
Back Plate
Clip
Ball Nut (F)
Wire Nut
Mounting Screw (E)
Headless Screw (D)
Mounting Plate (A)
House Grounding Wire
Green Grounding Screw (G)
Fixture Grounding Wire
Wire Nut (C)
Outlet Box Fixture Wire
Lock Nut (B) Rubber Pad (I)
Parts:
Photocell
IMPORTANT:
The sensor has an excellent photocell function
to enable the light to turn on at dusk and off at
dawn automatically.
121121
Parts Number (4600MM) Parts Number (9386SC)
Mounting Screw (E)
Green Grounding
Screw (G)
Lock Nut (B)
Wire Nut (C)
Glass Panel (H) (X3)
Mounting Plate (A)
Headless Screw (D) Ball Nut (F)
notch
Fig.3
Rubber Pad (I)
Fig.1

4. Take a glass panel and gently slide the glass panel upward into the notch inside of the metal frame in place,
secure it by pressing the clips from bottom sides. (See Fig.2 & Fig.3) Repeat with other panels.
5. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections by using
the wire nuts:
---Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
---Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power source.
---Attach the fixture grounding wire to the mounting plate with the green grounding screw. Then connect it to
the house grounding wire with a wire nut.
Carefully put the wires back into the outlet box.
6. Attach the back plate to the mounting plate by inserting the headless screws, then secure it with rubber
pads and ball nuts.
CAUTION: With silicone caulking compound, caulk completely around where the back plate meets
with the wall surface to prevent water from seeping into the outlet box.
7. Turn on the power at the main fuse or circuit breaker box.
121121

1. Turn off the power at the main fuse or circuit breaker box before starting installation.
2. Loosen the wire nuts connected with the wires from photocell. (See Fig.1)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire nuts: (See Fig.2)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
4.Turn on the power at the main fuse or circuit breaker box
Photocell
White Wires From Photocell
Wire Nuts
Wires From Fixture
Wires From Fixture
Wires From
Main Power
Wire Nut
White Pigtail
Pigtail
Red Wires From Photocell
Black Wires From Photocell
Operation the Unit Without Photocell
Fig.1 Fig.2
121121
A: 7-3/4"
B: 19-1/2"
C: 6"
A
C
B