Vaxcel T0085 Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0085
Back Plate
Ball Nut (G)
Bulb Type B Max.60W
(not included)
Rubber Pad (H)
Parts:
140324
Parts Number (5007MM)
Mounting Screw (B)
Green Grounding
Screw (C)
Lock Nut (F)
Wire Nut (E)
Cross Bar (A) Ball Nut (G)
Metal Frame
Headless Screw (D)
Parts Number (9575CE)
Rubber Pad (H)
Photocell
IMPORTANT:
The sensor has an excellent photocell function
to enable the light to turn on at dusk and off at
dawn automatically.
Ball Nut Assembly
Fixture
Exterior Glass Shade (J)
Cross Bar (A)
House Grounding Wire
Green Grounding Screw (C)
Fixture Grounding Wire
Wire Nut (E)
Outlet Box
Fixture Wire
Mounting Screw (B)
Lock Nut (F)
Headless Screw (D)
Parts Number (9576AM)
Interior Glass Shade (I)
Clip
Fig. 1
Metal Frame
Clip
Glass Holder
Exterior Glass Shade (J)
Interior Glass Shade (I)
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau
central de disjoncteurs avant d’installer le luminaire.

140324
1. Turn off the power at the main fuse or circuit breaker box before starting installation.
2. Loosen the wire nuts connected with the wires from photocell. (See Fig.2)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
Photocell
White Wires From Photocell
Wire Nuts
Wires From Fixture
Wires From Fixture
Wires From
Main Power
Wire Nut
White Pigtail
Pigtail
Red Wires From Photocell
Black Wires From Photocell
Operation the Unit Without Photocell
Fig.2 Fig.3
1. Thread two headless screws through the cross bar, then secure them with four lock nuts (two on
each side of the cross bar). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will
be level.
2. Attach the cross bar to the outlet box by using two mounting screws.
3. Place the exterior glass shade into the metal frame carefully, and then secure it by pressing the
clips from the top sides. (See Fig.1)
Note: Slide the outer glass shade downward into the notch inside of the metal frame.
4. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections
using the wire nuts:
---Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
---Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power source.
---Attach the fixture grounding wire to the cross bar with the green grounding screw. Then connect
it to the house grounding wire with a wire nut.
Carefully put the wires back into the outlet box.
5. Attach the back plate to the cross bar by inserting the headless screws, then secure it with rubber
pads and two ball nuts.
Note: With silicone caulking compound, caulk completely around where the back plate
meets with the wall surface to prevent water from seeping into the outlet box.
6. Install a bulb (not included). See relamping label at socket area or packaging for maximum
allowed wattage.
7. Attach the interior glass shade to the glass holder and turn it clockwise until it locks in place.
Note: Do not over tighten.
8. Attach the metal frame to the fixture, then secure it with the ball nut assemblies.
9. Turn on the power at the main fuse or circuit breaker box.

140324
A: 6-1/2"
B: 10-1/2"
C: 8"
A
C
B
3. Take a white pigtail and black pigtail and make wire connections using wire nuts: (See Fig.3)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.