Vaxcel T0414 Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0414 / T0415
180408
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Hardware Package (included):
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Decorative cover Fixture Mounting Screw
Mounting StrapMounting Screw X2
#10/24 X1/4 in
Wire Connector X3
Page 1 / 3
Wall Mounted Eave Mounted
Note: Fixture can be wall mounted or eave mounted.
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the photocell, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 44 W
Working Temperature Range: - 4°F ~ 113°F
Features:
1. Energy saving LED fixture.
2. Photocell keeps the light OFF during daylight hours.
3. When in manual override mode, it can be switched
from 100％high level to low level brightness.

IMPORTANT:
FUNCTION:
The fixture features a photocell sensor which enables the light to turn on at dusk and off at
dawn automatically.
Turn off the power at fuse or circuit box.
180408
Page 2 / 3
1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two
mounting screws that best fit the outlet box. Back plate should sit flush against wall surface when secured.
(Choose one matching pair of suitable mounting screws from the 3 pairs provided)
2. Pull out the source wires from the outlet box. Make wire connections using wire connectors as follows:
---Connect the black wire from the fixture to the black wire from the power source (usually black).
---Connect the white wire from the fixture to the white wire from the power source (usually white).
Carefully tuck the wires back into the outlet box.
3. Attach the back plate of the light to the mounting strap, secure it with the fixture mounting screw.
4. Push the decorative cover firmly into the fixture mounting screw hole on
the light.
5. With silicone caulking compound, caulk completely around where the back
plate meets the wall surface.
CAUTION: Be sure to caulk completely where the back plate meets
the wall surface to prevent water from seeping into the outlet box.
Manual Override Mode (nighttime operation only)
● To temporarily override the settings in “ 100% Brightness ”,
100% Brightness modes switch to manual override, turn the
wall switch “OFF” then turn it “ON” twice within 3 seconds.
switch to low level. To shift back to “ 100% Brightness
mode”, turn the wall switch “OFF” then turn it “ON” twice
within 3 seconds again.
● The light turns off automatically at dawn. ( See Fig.1 )
FRONT
Mounting Strap
Outlet Box
Wire Connector
Back Plate
Mounting Screw
Light Head
Photocell
Fixture Mounting Screw
Decorative cover
Light fixture should be mounted as shown above when installed (depending upon type of installation)
Installation Steps
100% Brightness
( low-level and
high-level ) Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON
-OFF-ON in 0.5~3
Seconds
Turn wall switch OFF-ON
-OFF-ON in 0.5~3 Seconds
Fig. 1

Page 3 / 3 180408
Turn on the power at the main fuse or circuit breaker box.
6. Gently grasp the light heads and move them up or down, left or right to
adjust the light coverage area. Keep the light heads 30˚ below horizontal
to avoid water damage and electrical shock (See Fig 2) .
Note: When power is first applied, the light will turn on immediately. Wait for 15 seconds to allow the sensor to
warm up.
Assembly Kit
5852MM (1 SET) For T0414
5853MM (1 SET) For T0415
The following parts are available for re-order if damaged or missing.
Mounting Screw X2
#6/32 X1/2 in Decorative cover Fixture Mounting Screw
Mounting Strap
Mounting Screw X2
#10/24 X1/4 in Wire Connector X3
Fig. 2
AC
B
A: 9"
B: 6-1/4"
C: 5-3/4"
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.
This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided
that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof
of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty
does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed,
overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded
from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other
than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no
warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.
Troubleshooting
---The light does not come on at all:
1. Make sure the wall switch and circuit breaker are on.
2. Make sure the wiring is correct.
Mounting Screw X2
#8/32X1/2 in