Vendors Exchange VE1020579 User manual

1
QUICK REFERENCE GUIDE
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide)
AP Dual Drive Tray − Kit No. VE1020580 (5 Wide)
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A
R
# PART NUMBER DESCRIPTION
1 VE2995 VEND MOTOR
2VE9323B SELF DRILLING SCREW
3VE106272
GEAR SET WITH
LOOSE HUB COMPONENT
Please read the following instructions to install this kit on your tray.
Remove the kit from its packaging and check for any missing parts or
quality issues. If any parts are missing or damaged, contact Vendors
Exchange at the number below.
1
2
3
Any coils mentioned in this document are ordered separately from these kits.

2
R
QUICK REFERENCE GUIDE
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A
First, insert Backing Plate with Gears (VE106272) into the slots in the tray motor slot as shown (A). Using the Self-Drilling Screw
(VE9323B), hold the backing plate in position while installing the screw as shown (B).
Before Install After Install
1
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
Screw Thru
Slots on Tray Motor Wall
Vend Motor
Self Drill Screw
Self Drill Screw
AB
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide) − VE1020580 (5 Wide)

3
R
QUICK REFERENCE GUIDE
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A
Install Coil
End of Left Coil
2
Then, install the left coil. Rotate the coil so that the end is at the 6-o’clock position at the
end of the install.
12
6
End of Left Coil
12
6
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
Installed Coil
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide) − VE1020580 (5 Wide)

4
R
QUICK REFERENCE GUIDE
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A
3
4
Next, install the Right Coil to the Loose
Gear/Hub.
Then, install the Right Side Coil and the Gear/Hub
on the Motor Hub position as shown in the detail
above, making sure that the snaps on the Motor
Hub fully engage into the recessed area on the
Gear/Hub and the end of the Coil should end at the
6-o’clock position (see symbol).
6-o’clock position
Snaps on Motor
Detail of Motor
Hub Tabs
Right Coil
Loose Gear/Hub
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide) − VE1020580 (5 Wide)
12
6

5
R
QUICK REFERENCE GUIDE
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A
5
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
Finally, repeat steps 2 through 4 to complete
the Coil Installation. Check the ends to main-
tain the 6-o’clock position on each one, adjust
if necessary
12
6
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide) − VE1020580 (5 Wide)
12
6
12
6

R
QUICK REFERENCE GUIDE
www.veii.com
1-800-321-2311
8700 BROOKPARK ROAD
CLEVELAND, OH 44129
©2021, VENDORS EXCHANGE® INTERNATIONAL, USA
VE1020573, REVISION A 6
GEAR DRIVE ASSEMBLY KIT INSTRUCTIONS
AP Dual Drive Tray − Kit No. VE1020579 (4 Wide) − VE1020580 (5 Wide)
NOTES