Verco DNA DD 1206 User manual

DNA desking
DD 1206/1406/1606/0808/1208/1408/1608/1808/
DD 2008/2208/2010/2210
DNA stand-alone desk
1 x DD----
1 x DSH (pair)
1 x DR 22/20/18/
16/14/12/08 (pair)
1 x DR 06/08/10
(pair)
6 mm Allen key 4 mm Allen key
Equipment Required
(not included)
Fixings
Take one of the corner legs and one of
the shorter rails (if you have a DD0808 or
DD 1616 all rails will be the same length
so start with any of them). With the holes
in the rail facing upwards, insert either
end of the rail onto one of the metal
lugs at the top of the leg. If the rail will
not slide on easily ensure that the bolts
in the lug are fully retracted by turning
them clockwise with the Allen key.
With the beam in place, put the Allen
key through one of the holes in the top
of the beam and into the Allen bolt in
the metal lug of the leg. Turn this
anti-clockwise as if to undo the bolt.
This will raise the bolt up and force it
against the inside of the beam, locking
it in place. Repeat this with the bolt
directly next to the one you have just
turned.
2 x DCL (pairs)
8 x 6mm x 26mm
mush head screws

In the same way as the short beam
place and x the long beams in
between the two structures. Place both
beams before securing them in place
as once one is in place the structure will
be locked in place.
Remember to turn the bolts anti-
clockwise to x the beams in place.
Once complete check that all the
beams are securely fastened to the
legs.
Repeat this process with the remaining
leg of the pair, xing it to the other end
of the beam. The result should resemble
this illustration.
Repeat steps 1-3 with the remaining
short beam and the other pair of legs.
You should now have two identical
structures.

Lay the top on the oor, underside
facing up (pilot holes facing up). Place
the frame on top of it as shown and
align the two oval shaped holes in each
leg with the pilot holes in the top. Place
the spacer hooks, one under each of
the long beams, with the hooks facing
towards the centre of the desk and the
beam sitting in the shallow recess in the
block.
Take all the spacer hook components
(grey plastic) out of their packaging.
Take one of the rectangular blocks and
one of the hooks. With the ‘Verco’ and
‘100-DNASH’ text on the inside of the
moulding facing up, insert the hook in
to the central hole as shown left.
The hook will not immediately t through
the hole. You need to brace the block
with both hands and push on the end
of the hook where the arrow shows very
rmly using your thumb. The hook will
pass though the hole making a clearly
audible ‘click’ as it does.
Now fully insert the top of the hook into
the rectangular recces in the block as
shown right. Push it fully in to the recess
so the top is ush with the top of the
block.

With the assistance of at least one other
person turn the desk so that it stands
on its legs. Your completed desk should
resemble the image on the left.
Adjust the feet if needed by turning
them individually to adjust their height.
Each foot should be rmly placed on
the oor ensuring that the desk does not
wobble.
Place the black ‘mush head’ screws
through the holes in each leg and
screw them into the underside of the
top using the 4mm Allen key. Continue
turning until the fully inserted but avoid
over-tightening.
This step is not essential. You can x the
spacer hook into position by sliding it
to the desired position and screwing
through the two holes in its base and
into the underside of the desk top.
There are no pilot holes for this as the
hook can be placed anywhere along
the length of the beam.