Vertical Summit80 User manual

Vertical Summit80 & Summit800
Feature Description & Operation
Manual
Please read this manual carefully before operating System.
Retain it for future reference.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
Revision History
Copyright© 2014 Vertical Communications. All Rights Reserved
This material is copyrighted by Vertical Communications.Any unauthorizedreproductions, use or
disclosure of this material, or any part thereof, is strictly prohibited and is a violation of Copyright Laws.
Vertical Communications reserves the right to make changes in specifications at any time without notice.
The information furnished by Vertical Communications in this material is believed to be accurate and
reliable, but is not warranted to be true in all cases. If you are not the intended recipient, you should
destroy or retrieve this material to Vertical Communications.
iPECS is trademark of Ericsson-LG Enterprise Co., Ltd.
All other brand and product names are trademarks or registered trademarks of their respective
companies.
SW version
Issue
Date
DESCRIPTION OF CHANGES
1.0Fe
1.0
Feb, 2014
Initial Release
1.1.x
1.1
Feb, 2015
Update contents according to S/W integration for both Summit80 &
Summit800
1.2.x
1.2
Updated andAdded the following features:
- Emergency page
- Message Cascade
- LCR (Least Call Routing)
- Remote Control from mobile Phone
- ARS (Alternative Route Selection) for Digit conversion table
- Message Wait Reminder Tone
- Call park for internal call
- Unified Loop button

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
i
Table of Contents
1. Introduction.............................................................................. 1
1.1 Manual Application...................................................................... 1
1.2 Manual Organization.................................................................... 1
1.3 Feature Information..................................................................... 1
1.4 Buttons & Term Variations.......................................................... 2
2. System...................................................................................... 3
2.1 8-Digit Station Numbering Plan.................................................. 3
2.2 Account Code............................................................................... 4
2.3 Alarm Signal/Door Bell................................................................ 6
2.4 Authorization Codes (Password) ............................................... 8
2.5 Auto Call Recording .................................................................. 11
2.6 Auto Call Release....................................................................... 13
2.7 Automatic Call Distribution (ACD) ........................................... 14
2.7.1 ACD Caller Controlled ICLID Routing..................................................14
2.7.2 ACD Statistics Report ..........................................................................15
2.7.3 Agents..................................................................................................17
2.7.3.1 Agent Auto Connect/Zap Tone ..............................................................17
2.7.3.2 Agent Automatic Wrap-Up.....................................................................18
2.7.3.3 Agent Help Request...............................................................................19
2.7.3.4 Agent Id Login/Logout............................................................................20
2.7.3.5 Agent On/Off Duty w/Reason Code.......................................................23
2.7.3.6 Agent Queued Calls Display..................................................................25
2.7.4 Announcements...................................................................................27
2.7.5 Auto ACD DND Unavailable Service...................................................29
2.7.6 Calls-In-Queue routing.........................................................................30
2.7.7 Calls-In-Queue Page Alert...................................................................31
2.7.8 Event Messages...................................................................................33
2.7.9 Group Mail Box ....................................................................................34
2.7.10 Group Name.........................................................................................35
2.7.11 Incoming Call Routing..........................................................................36
2.7.12 Supervisors ..........................................................................................37
2.7.12.1 Agent Call Monitor..................................................................................37
2.7.12.2 Agent Status Control..............................................................................39
2.7.12.3 Group Status Display.............................................................................40

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
ii
2.7.12.4 Group Parameter Control.......................................................................42
2.7.12.5 Supervisor Help Response....................................................................43
2.7.12.6 Supervisor Login/Logout........................................................................45
2.8 Auto Called Number Redial (ACNR)......................................... 47
2.9 Automatic Pause Insertion........................................................ 49
2.10 Automatic Privacy...................................................................... 50
2.11 Auto Service Mode Control....................................................... 51
2.12 Automatic System Daylight Saving Time................................ 53
2.13 Automatic Time Synchronization............................................. 54
2.14 Call Duration Warning Tone...................................................... 55
2.15 Call Forward............................................................................... 56
2.16 Call Forward, Preset.................................................................. 60
2.17 Call Park...................................................................................... 62
2.18 Call Pick-Up................................................................................ 63
2.18.1 Directed Call Pick-Up...........................................................................63
2.18.2 Group Call Pick-Up ..............................................................................64
2.18.3 Pick Up Group Call Pick-Up.................................................................65
2.19 Call Re-Routing (CRR)............................................................... 67
2.20 Call Transfer............................................................................... 68
2.20.1 Call Transfer, Outside Line ..................................................................68
2.20.2 Call Transfer, Station ...........................................................................69
2.20.3 Call Transfer, System Announcement.................................................71
2.20.4 Call Transfer, Voice Mail......................................................................72
2.21 Call Waiting/Camp-On............................................................... 74
2.22 Conference................................................................................. 75
2.22.1 Conference Group................................................................................75
2.22.2 Conference Member View & Delete ....................................................78
2.22.3 Conference Room................................................................................79
2.22.4 Multi-Party Conference ........................................................................81
2.22.5 Unsupervised Conference ...................................................................82
2.23 Customer Site Name.................................................................. 84
2.24 Data Line Security...................................................................... 85
2.25 Delayed Line Ring...................................................................... 86
2.26 Delayed Auto Attendant............................................................ 87
2.26.1 DISA Incoming Line-Russia-................................................................87
2.26.2 Normal Line Ring Assignment .............................................................88

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
iii
2.27 Diagnostics & Maintenance...................................................... 89
2.28 Dial-by-Name.............................................................................. 90
2.29 Dial Pulse to Tone Switchover.................................................. 92
2.30 Dialing Restrictions................................................................... 93
2.30.1 Class of Service ...................................................................................93
2.30.2 Day/Timed & Night Station COS (Class of Service)............................96
2.30.3 Temporary Station COS (Class of Service)/Lock ................................97
2.30.4 Walking COS (Class of Service)........................................................100
2.31 Digit Conversion...................................................................... 102
2.32 Alternative Route Selection(ARS) for Digit conversion table104
2.33 Differential Ring....................................................................... 105
2.34 DND (Do Not Disturb) .............................................................. 107
2.35 Door Open ................................................................................ 108
2.36 Emergency Call Service.......................................................... 110
2.36.1 Emergency Call..................................................................................110
2.36.2 Emergency Call Caller-Location Support...........................................111
2.36.3 Emergency Call –Bomb Threat History .............................................113
2.36.4 Emergency Mailbox............................................................................114
2.36.5 Emergency Call Monitor.....................................................................115
2.37 Executive/Secretary Forward.................................................. 116
2.38 External Auto Attendant/Voice Mail....................................... 118
2.38.1 AA/VM Group.....................................................................................118
2.38.2 In-band (DTMF) AA/VM Signaling.....................................................119
2.38.3 SMDI (Simplified Message Desk Interface) AA/VM Signaling...........120
2.38.4 Voice Mailbox Translation..................................................................122
2.39 Flexible Numbering Plan......................................................... 124
2.40 Forced Disconnect Intrusion.................................................. 125
2.41 Green Power Save ................................................................... 126
2.42 Headset Compatibility............................................................. 127
2.43 Hold........................................................................................... 129
2.43.1 Automatic Hold...................................................................................129
2.43.2 Hold Preference.................................................................................130
2.43.3 Hold Recall.........................................................................................131
2.43.4 Exclusive Hold....................................................................................132
2.43.5 System Hold.......................................................................................133
2.44 Hot Desk ................................................................................... 135

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
iv
2.45 ICLID Call Routing ................................................................... 137
2.46 In-Room Indication .................................................................. 139
2.47 Integrated Auto Attendant/Voice Mail.................................... 140
2.47.1 Integrated AA/VM Overview...............................................................140
2.47.2 Integrated Auto Attendant..................................................................141
2.47.2.1 Company Directory..............................................................................143
2.47.2.2 Remote Announcement Recording......................................................145
2.47.3 Integrated Voice Mail .........................................................................146
2.47.3.1 Administrator Mailbox...........................................................................146
2.47.3.2 Announce Only Mailbox.......................................................................147
2.47.3.3 Call Forward from VM..........................................................................148
2.47.3.4 Distribution Lists...................................................................................149
2.47.3.5 E-Mail Notification................................................................................150
2.47.3.6 Mark a Message as Private .................................................................151
2.47.3.7 Mark a Message for Delivery Confirmation..........................................152
2.47.3.8 Message Cascade...............................................................................153
2.47.3.9 Message Retrieval...............................................................................154
2.47.3.10 Message Retrieval Options..................................................................156
2.47.3.11 Message Storage.................................................................................158
2.47.3.12 Outbound Message Notification...........................................................160
2.47.3.13 Personal CCR/User Greeting DISA.....................................................162
2.47.3.14 Remote Message Retrieval..................................................................163
2.47.3.15 Send a Message..................................................................................164
2.47.3.16 Voice Mail Class of Service..................................................................165
2.47.3.17 Voice Mailbox Settings.........................................................................166
2.47.4 System Voice Memo..........................................................................167
2.48 IP Bridge Mode......................................................................... 169
2.49 IP FAX Relay, T.38 Support..................................................... 170
2.50 IP System DECT....................................................................... 171
2.51 IP TRANS-CODING .................................................................. 172
2.52 IP TRUNKING............................................................................ 173
2.52.1 H.323 v4 Service................................................................................173
2.53 LBC (Loud Bell Control).......................................................... 175
2.54 LCR (Least Cost Routing)....................................................... 176
2.55 Linked Station Pairs ................................................................ 178
2.56 LNR (Last Number Redial) ...................................................... 180
2.57 Mobile Extension ..................................................................... 182
2.58 MOH (Music-On-Hold).............................................................. 184
2.59 Multiple Language Support..................................................... 186

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
v
2.60 Multiple Voice Mailbox Support.............................................. 188
2.61 Network Security & Priority .................................................... 189
2.62 Outside Call Redirect............................................................... 190
2.63 Outside Call Time Restriction................................................. 191
2.64 Outside Line Access................................................................ 192
2.65 Outside Line Queuing.............................................................. 194
2.66 Personal Groups...................................................................... 196
2.67 PPP over MODU....................................................................... 197
2.68 Pre-Defined & Custom Text Display Messages .................... 198
2.69 Prefix Dialing Table.................................................................. 202
2.70 Prepaid Call.............................................................................. 203
2.71 Remote Control from Mobile Phone....................................... 204
2.72 Ringing Line Preference.......................................................... 206
2.73 Speed Dial................................................................................. 207
2.73.1 Display Security..................................................................................207
2.73.2 Speed Dial Pause Insertion................................................................208
2.73.3 Station Speed Dial .............................................................................209
2.73.4 System Speed Dial.............................................................................212
2.73.5 System Speed Zone (Groups)...........................................................215
2.74 Station Call Coverage.............................................................. 216
2.75 Station Groups......................................................................... 218
2.76 SMDR (Station Message Detail Recording)........................... 222
2.76.1 Call Cost Display................................................................................222
2.76.2 Lost Call Recording............................................................................224
2.76.3 SMDR Call Records...........................................................................226
2.77 System Administration............................................................ 229
2.77.1 Keyset Administration ........................................................................229
2.77.2 Multi-Level Admin Access..................................................................230
2.77.3 Web Administration............................................................................231
2.78 System Alarm Notification Control ........................................ 233
2.79 System Networking.................................................................. 235
2.79.1 Centralized Control T-NET.................................................................235
2.79.2 Distributed Control Network...............................................................236
2.79.2.1 Net Intercom Call .................................................................................237
2.79.2.2 Net Call Transfer..................................................................................239
2.79.2.3 Net Call Identification Service..............................................................241

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
vi
2.79.2.4 Network Call back (Call Completion) ...................................................241
2.79.2.5 Net Call Camp-On (Call Offer).............................................................242
2.79.2.6 Net Conference....................................................................................244
2.79.2.7 Net Station Message Waiting...............................................................245
2.79.2.8 Net Call Forward..................................................................................247
2.79.2.9 CO Transit-In........................................................................................249
2.79.2.10 CO Transit-Out.....................................................................................250
2.79.2.11 BLF Presentation.................................................................................252
2.79.2.12 Attendant Call (CAS)............................................................................253
2.79.2.13 Centralized Voice Mail .........................................................................254
2.79.2.14 Networked System Paging...................................................................255
2.80 Traffic Analysis........................................................................ 257
2.80.1 Traffic Analysis, Attendant .................................................................259
2.80.2 Traffic Analysis, Call Reports.............................................................261
2.80.3 Traffic Analysis, H/W Usage ..............................................................262
2.80.4 Traffic Analysis, Line Reports ............................................................263
2.81 System Scenario Call Routing................................................ 265
2.82 Universal Night Answer (UNA) ............................................... 267
2.83 Wake-Up Alarm, Enhanced..................................................... 268
2.84 Wake-up Alarm, Standard....................................................... 271
2.85 Web Call Back.......................................................................... 273
2.86 Zone Management ................................................................... 274
2.86.1 Holiday Assignment ...........................................................................274
2.86.2 Inter Zone Connection Limit...............................................................275
2.86.3 Remote Devices.................................................................................276
2.86.4 Zone Outgoing Call Connection Limit................................................277
3. Intercom................................................................................278
3.1 Barge In..................................................................................... 278
3.2 Direct Station Selection/Busy Lamp Field (DSS/BLF).......... 280
3.3 Intercom (ICM) Call.................................................................. 281
3.4 Intercom Call Hold................................................................... 283
3.5 Intercom Caller Controlled Signaling..................................... 284
3.6 Intercom Lock-Out................................................................... 285
3.7 Intercom Step Call ................................................................... 286
3.8 Intercom Tenancy Group ........................................................ 287
3.9 Intercom Transfer .................................................................... 289
3.10 Message Wait/Call Back.......................................................... 291

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
vii
3.10.1 CLI Message Wait..............................................................................291
3.10.2 Message Wait Reminder Tone ..........................................................294
3.10.3 Short Message Service (SMS)...........................................................295
3.10.4 Station Message Wait/Call Back........................................................298
3.11 Paging....................................................................................... 301
3.11.1 Internal/External & All Call Page........................................................301
3.11.2 Meet Me Page....................................................................................304
3.11.3 SOS Paging........................................................................................305
3.12 Push to Talk Paging................................................................. 306
3.13 Emergency page...................................................................... 308
4. Outside (CO/IP) lines........................................................... 309
4.1 Auto Fault Detection and Recovery....................................... 309
4.2 Caller ID Mode.......................................................................... 310
4.3 CO Line Flash........................................................................... 311
4.4 CO Line Release Guard Time.................................................. 312
4.5 CO Line Ring Detect................................................................ 313
4.6Dial Pulse Signaling................................................................. 314
4.7 Direct Inward Dialing (DID)...................................................... 315
4.8 DID Line Digit Conversion....................................................... 317
4.9 Direct Inward System Access (DISA)..................................... 318
4.10 DTMF Signaling........................................................................ 320
4.11 IP Address Dialing................................................................... 321
4.12 IP Trunking............................................................................... 322
4.12.1 H.323 v4 Service................................................................................322
4.12.2 SIP Trunk Service..............................................................................323
4.13 IP WAN Dialing after Answer.................................................. 325
4.14 ISDN (Integrated Service Digital Network)............................. 326
4.14.1 Calling/Called Party Identification......................................................326
4.14.2 ISDN AOC (Advice of Charge)...........................................................328
4.14.3 Keypad Facility...................................................................................329
4.14.4 Multiple Subscriber Number (MSN)...................................................330
4.15 ISDN Supplementary Services................................................ 332
4.15.1 ISDN Call Deflection ..........................................................................332
4.15.2 ISDN Malicious Call ID Request........................................................333
4.16 Line Monitor ............................................................................. 335

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
viii
4.17 Multiple Calling Line ID ........................................................... 336
4.18 Outside Line Groups ............................................................... 338
4.19 Outside Line Preset Forward.................................................. 339
4.20 Outside Line Ring Assignment............................................... 340
4.21 Private Line............................................................................... 341
5. iPECS phone........................................................................342
5.1 Answering Machine Emulation............................................... 342
5.2 Auto Release of [SPEAKER]................................................... 344
5.3 Automatic Speaker Select....................................................... 345
5.4 Background Music (BGM)....................................................... 346
5.5 Call Log Display....................................................................... 348
5.6 Call Profile Routing.................................................................. 349
5.7 Call Wait for Internal & External calls.................................... 351
5.8 DND –One-Time DND.............................................................. 356
5.9 Flex Button Direct Speed Dial Assignment........................... 358
5.10 Flexible LED Flash Rates........................................................ 359
5.11 Group Listening....................................................................... 360
5.12 Intercom Signaling Mode........................................................ 361
5.13 Microphone Mute..................................................................... 362
5.14 Off-Hook Signaling .................................................................. 363
5.15 On-Hook Dialing....................................................................... 364
5.16 Outside Line Name Display..................................................... 365
5.17 Prime Line Immediate/Delayed............................................... 366
5.18 Ring Tone Selection and Download....................................... 368
5.19 Save Number Redial (SNR)..................................................... 369
5.20 Serial DSS/BLF Console.......................................................... 370
5.21 Silent Text Message................................................................. 372
5.22 Speakerphone.......................................................................... 373
5.23 Station Flexible Buttons.......................................................... 374
5.24 Station Individual Call Routing (ICR) ..................................... 376
5.25 Station User Programming & Codes...................................... 378
5.26 Two-Way Record...................................................................... 384
5.27 Voice Over................................................................................ 386

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
ix
6. Attendants............................................................................ 388
6.1 Alternate Attendant.................................................................. 388
6.2 Attendant Call & Call Queuing................................................ 390
6.3 Attendant Positions................................................................. 391
6.4 Attendant Recall....................................................................... 392
6.5 Attendant Station User Program Codes................................ 393
6.6 Call Forward, Attendant .......................................................... 397
6.7 Call Forward, Off-Net............................................................... 398
6.8 Day/Night/Timed/Scenario Ring Mode................................... 400
6.9 DSS/BLF Consoles .................................................................. 402
6.10 Disable Outgoing Line Access............................................... 404
6.11 DND Override ........................................................................... 405
6.12 Emergency Call Attendant Alert............................................. 406
6.13 Feature Cancel......................................................................... 408
6.14 IP-Attendant.............................................................................. 409
6.15 Intrusion.................................................................................... 410
6.16 LCD Display Format Control................................................... 411
6.17 System Clock Set..................................................................... 412
7. SLT (Single Line Telephone).............................................. 414
7.1 Broker Call................................................................................ 414
7.2 Howler Tone ............................................................................. 416
7.3 SLT Flash Mode ....................................................................... 417
7.4 SLT Message Wait Indication ................................................. 418
7.5 SLT Name Entry....................................................................... 419
7.6 Transfer CLI to SLT.................................................................. 420
8. SIP extension.......................................................................421
8.1 SIP Phone Support .................................................................. 421
8.2 SIP Phone Provisioning, Ericsson-LG Enterprise Phones.. 424
8.3 SIP Virtual Mobile Extension .................................................. 426
9. iPECS UCS Client................................................................ 427
9.1 iPECS UCS Premium & Standard Client Support................. 427
9.2 Call Control with UC Client..................................................... 428

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
1
1. INTRODUCTION
1.1 Manual Application
This document provides detailed information covering description and operation of the
numerous features available in the Vertical Summit Release system software. The document is
written assuming the system employs the default-numbering plan for North America.
1.2 Manual Organization
Features are arranged alphabetically in nine (9) different major groupings as follows:
Section 1 Introduction
Section 2 System Features
Section 3 Intercom Features
Section 4 CO/IP lines
Section 5 iPECS IP & LDP Phones
Section 6 Attendant
Section 7 SLT
Section 8 SIP Extension
1.3 Feature Information
Each section is an alphabetical listing of features with the description and operation of each.
The structure is divided into 6 parts as below:
Description: explains the nature of the feature.
Operation: gives detailed step-by-step operation of the feature for Ericsson-LG
Enterprise phones (LDP digital and LIP IP phones) and SLTs. In some cases a
Flexible button on the Ericsson-LG Enterprise phones can be assigned to activate the
feature. In this case, the user entries to assign the button are provided.
Conditions: explains known feature interactions and constraints related to the
feature.
Programming: lists database entries that may be required for proper feature
operation. This lists are related to Station Admin programming on Summit
Administration and Programming manual. Regarding WEB admin, you directly
access to the web admin and check the programming.
Reference: lists related topical information to aid in understanding the feature.
Hardware: lists hardware required for proper feature operation.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
2
1.4 Buttons & Term Variations
The Summit supports proprietary digital and IP phones. The proprietary models include the LDP-
7000 series, LDP-9000 series, LIP- 7000 series, LIP-8000/8000E series, and LIP-9000 Series.
Each series employs similar but slightly different designations for the buttons. Details of the
buttons on your phone are provided in the User Guide. For the purposes of this manual, several
of the designations may be used. For example, the button to handle messages is called either
[MSG], [CALL BK], or [MESSAGE/CALLBACK]. Note the fixed button names are enclosed in
brackets ‗[ ]‘ and Flex buttons are enclosed in braces ‗{ }‘. In addition, some buttons have dual
functions; the [HOLD/SAVE] button places your active call on hold and stores entries you make
when assigning Flex buttons.
The description, operation and conditions attempt to use common terms such as ―Voice Mail‖or
―outside Line‖so that a novice installer can understand the contents. The Programming and
Hardware sections however employ terms specific to the Summit as used in the respective
manual such as ―VSF‖(used for voice mail) and ―CO/IP lines‖ for outside Lines.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
3
2. SYSTEM
2.1 8-Digit Station Numbering Plan
Description
The system supports Station Numbering Plans from two to eight digits. The Station number
consists of a Prefix and suffix called Add Digits. A Prefix digit string can be any four digits that do
not conflict with the system Flexible Numbering Plan used for feature codes. This fixed digit string
is added to the Add Digits string, which can be 2 to 4 digits in length, to uniquely identify each
Station.
Operation
System
Operation of the 8-digit Station Numbering Plan is automatic when configured
Conditions
1. The system employs the complete Station number, 2 to 8 digits, when sending
messages to an external device such as an adjunct Voice Mail and TAPI device such
as ez-Attendant. It is the responsibility of the 3rd party software to support the defined
Station Numbering Plan.
2. The 8-digit numbering is configured in the 8-Digit Table (PGM 238).
Programming
Keyset Admin.
System ID
Prefix Usage (PGM 238)
8-Digit Table (PGM 238)
Web Admin.
SYSTEM ID &
NUMBERING PLANS
8 Digit Extension Table8 Digit String, Add Digit-
Related Features
Station Numbering Plan
Hardware

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
4
2.2 Account Code
Description
You may allow tracking of specific calls by entering a non-verified variable length (up to 12 digits)
identifier for a call. The identifier or ―Account Code‖ is output as part of the Station Message
Detail Record (SMDR) for the call as discussed in Section 2.76. This is often used to allocate
call costs to a specific account or client.
Operation
iPECS IP & LDP Phones
To assign a Flex button for {ACCOUNT CODE} operation:
[TRANS/PGM] + {FLEX} + [TRANS/PGM] + ―84‖ + [HOLD/SAVE]
To assign a Flex button for {ONE-TOUCH ACCOUNT CODE} operation:
[TRANS/PGM] + {FLEX} + [TRANS/PGM] + ―84‖ + Account code (up to 12 digits) +
[HOLD/SAVE]
To enter an Account Code using an {ACCOUNT CODE} button prior to placing a call:
1. Lift the handset.
2. Press the {ACCOUNT CODE} button.
3. Dial the Account Code (up to 12 digits).
4. Press ―*‖, Intercom dial tone is heard.
5. Place the outside call as normal.
Or,
1. Lift the handset or press the [SPEAKER] button.
2. Press the {ONE-TOUCH ACCOUNT CODE} button.
3. Place the outside call as normal.
To enter an Account Code using an {ACCOUNT CODE} button during a call:
1. Press the {ACCOUNT CODE} button.
2. Dial the Account Code (up to 12 digits).
3. Press ―*‖.
Or,
Press the {ONE-TOUCH ACCOUNT CODE} button.
SLT
To enter an Account Code prior to placing a call:
1. Lift the handset.
2. Dial the Flex Numbering Plan code ―550‖.
3. Dial the Account Code (up to 12 digits).

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
5
4. Press ―*‖.
5. Place the outside call as normal.
To enter an Account Code during a call:
1. Momentarily press the Hook-switch.
2. Dial the Flex Numbering Plan code ―550‖.
3. Dial the Account Code (up to 12 digits).
4. Press ―*‖.
Conditions
1. When entering an Account Code during a call, DTMF digits are transmitted to the
connected party.
2. A maximum of 1000 {ONE-TOUCH ACCOUNT CODE} buttons may be assigned in
the system.
3. If an Authorization Code is entered as the Account Code, the SMDR record will show
the station number or the index number for a System Authorization Code rather than
the user entered Authorization Code.
4. If the Forced SMDR Account Code attribute of the station is enabled, you must enter
an Account Code prior to placing an outgoing call.
Programming
Keyset Admin.
NUMBERING
Flexible Numbering Plan (PGM 106-Button 8)
STATION
Forced SMDR Account Code (PGM 113-Button 24-21)
Web Admin.
SYSTEM ID
&NUMBERING PLANS
Flexible Numbering Plan SMDR Account Code Enter
STATION DATA
Common Attributes Forced SMDR Account Code
Related Features
Authorization Codes (Password)
SMDR (Station Message Detail Recording)
Station Flexible Buttons
Hardware

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
6
2.3 Alarm Signal/Door Bell
Description
The system can be configured to recognize the status of an external contact (normally open or
closed). The system will signal assigned iPECS IP and LDP Phones when the contact activates.
This capability is commonly employed to provide remote Alarm or Door Bell signals a user.
Assigned stations receive the Alarm Signal, either a single tone burst repeated at 1-minute
intervals or a continuous tone. The Alarm Signal may be terminated at the phone by dialing the
Alarm Stop code or, if assigned, pressing the {ALARM STOP} button. To rearm the Alarm
function, the alarm condition must be cleared and the Alarm signal terminated.
When used as a Door Bell, assigned iPECS IP and LDP Phones receive a single tone burst each
time the external contact is activated and no reset is required.
Operation
System
At detection of contact operation, the Alarm/Door Bell signal is sent to assigned stations.
iPECS IP & LDP Phones
To assign a Flex button as an {ALARM STOP} button to terminate the Alarm Signal:
[TRANS/PGM] + {FLEX} + ―565‖ + [HOLD/SAVE]
To terminate an Alarm Signal, while idle:
1. Dial the Flex Numbering Plan code ―565‖, confirmation tone is received and the Alarm
Signal is terminated. If the alarm condition is cleared, the system will automatically rearm
the alarm monitoring.
Or, Press the {ALARM STOP} button.
Conditions
1. The Alarm contacts must be ―dry‖, no voltage or current source connected.
2. Only iPECS IP and LDP Phones may be assigned to receive Alarm/Door Bell signals.
3. The LCD of phones assigned to receive Alarm/Door Bell signals will show ―ALARM‖ or
―DOOR BELL‖ as appropriate.
4. The Alarm Stop code is also employed to terminate alarm signals from digital and IP
trunk alarms.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
7
Programming
Keyset Admin.
SYSTEM
Alarm Enable (PGM 163-Button 1)
Alarm Contact Type (PGM 163-Button 2)
Alarm/Doorbell Mode (PGM 163-Button 3)
Alarm Signal Mode (PGM 163-Button 4)
STATION
Alarm/Door Bell Attribute (PGM 113-Button 8)
Web Admin.
SYSTEM DATA
Alarm Attributes Alarm Enable, Alarm Contact Type,
Alarm/Doorbell Mode, Alarm Signal Mode
STATION DATA
Common Attributes Alarm/Door Bell Attribute
Related Features
Door Open
Hardware
iPECS IP or LDP Phone
Alarm or Doorbell input contact, refer to the Summit Hardware Description &
Installation Manual to install.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
8
2.4 Authorization Codes (Password)
Description
Authorization Codes provide a means to control access to Voice Mail, Off Premise Call Forward,
Walking COS (Class of Service), or DISA and may be required for outgoing outside Line or LCR
access based on configuration of the Summit system database. When you dial an Authorization
Code that matches an Authorization Code stored in the database, the system invokes the Station
COS (Class of Service) or the COS (Class of Service) assigned to Authorization code. Each
Authorization code has separate Day/Night mode COS (Class of Service) assignments.
There are two types of Authorization Codes, Station and System. A Station Authorization Code is
specifically related to a given station and intended for a single user. The System Authorization
Codes are intended for use by any station in the system.
The Station Authorization Codes includes the associated station number and the assigned code.
The structure of the System Authorization code can be set as either ―*‖, or ―*‖ the Authorization
table index and the code digits. The later allows duplicate codes to be employed using entry of
table index to provide a unique identification of the entry.
The Administrator and Attendants are permitted to assign any Authorization code including codes
for another station. Normal users may only assign the Station Authorization code for the specific
station.
Operation
iPECS IP & LDP Phones
To assign a Station Authorization Code:
1. Press the [TRANS/PGM] button.
2. Dial ―33‖, the Authorization Program Code.
3. Dial the Station number.
4. Dial the Authorization Code (1 to 12 digits).
5. Press the [HOLD/SAVE] button.
To enter an Authorization Code when second dial tone is received:
1. Dial the Station number for the Station Authorization code or, for a System Authorization
Code, dial ―*‖ or ―*‖ and the Authorization table index.
2. Dial the corresponding Authorization Code.
3. Place your call as normal.
SLT
To assign a Station Authorization code:
1. Lift the handset.
2. Dial SLT Program Mode Entry code ―561‖.

Vertical Summit80 & Summit800
Feature Description and Operation Manual Issue 1.2
9
3. Dial Authorization Program Code ―33‖.
4. Dial Authorization Code (1 to 12 digits).
5. Momentarily press the Hook-switch, receive confirmation tone.
To enter an Authorization Code when second dial tone is received;
1. Dial the station number for the Station Authorization code or, for a System Authorization
Code, dial ―*‖ or ―*‖ and the Authorization table index.
2. Dial the corresponding Authorization Code.
3. Momentarily press the Hook-switch.
4. Place your call as normal.
DISA
To enter an Authorization Code when second dial tone is received:
1. Dial the station number for a Station Authorization code or, for a System code, ―*‖ or ―*‖ and
the Authorization table index.
2. Dial the corresponding Authorization Code.
3. Place call as normal.
System Attendant
To assign an Authorization Code:
1. Press the [TRANS/PGM] button.
2. Dial Attendant Station Program code ―031‖.
3. Dial the Station number of a Station code or, for system code, ―*‖ or ―*‖ and the
Authorization table index.
4. Dial the corresponding Authorization Code.
5. Press the [HOLD/SAVE] button.
Conditions
1. When an outside DISA Line is marked for Authorization Code entry, the caller will hear
fast busy tone and must input a valid Authorization Code to continue. In case of an
entry error, the caller may retry entry of the code.
2. A DISA caller must enter a valid code within the number of attempts assigned as the
FAC (Forced Account Code) Retry Count. The station, if enabled, is placed to COS
(Class of Service) 7 after repeated failure attempts.
3. A user may enter an Authorization Code from any station to place an outside call using
Walking COS (Class of Service).
4. The Summit80 (Summit800) system provides memory for up to 500 (2400)
Authorization codes, 140 (1200) for station codes and the remaining 360 (1200) are
system codes.
5. Outside Line groups may be configured to require entry of a valid Authorization Code.
In this case, a second dial tone is provided when the Line group is accessed. If the
code entered is invalid, error tone is returned and the user must enter a valid code
within the FAC Retry Count.