Vertiv XTE PTS Series Operating and installation instructions

XTE PTS Series
PEIL/PESB Power Transfer Switches
Description and Installation Manual

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
The information contained in this document is subject to change without
notice and may not be suitable for all applications. While every precaution has
been taken to ensure the accuracy and completeness of this document, Vertiv
assumes no responsibility and disclaims all liability for damages resulting from
use of this information or for any errors or omissions. Refer to other local
practices or building codes as applicable for the correct methods, tools, and
materials to be used in performing procedures not specifically described in
this document.
The products covered by this instruction manual are manufactured and/or
sold by Vertiv. This document is the property of Vertiv and contains
confidential and proprietary information owned by Vertiv. Any copying, use or
disclosure of it without the written permission of Vertiv is strictly prohibited.
Names of companies and products are trademarks or registered trademarks of
the respective companies. Any questions regarding usage of trademark
names should be directed to the original manufacturer.
Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent section of this
manual to see if the issue can be resolved by following outlined procedures.
Visit https://www.vertiv.com/en-us/support/ for additional assistance.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
iii
TABLE OF CONTENTS
Admonishments Used in this Document.......................................................................................................................... v
Important Safety Instructions ............................................................................................................................................ vi
1 About this Document........................................................................................................................................................ 1
2 Description........................................................................................................................................................................... 1
2.1 Application ...........................................................................................................................................................................................................................................................................1
2.2 Cabinet Dimensions....................................................................................................................................................................................................................................................2
2.3 Construction......................................................................................................................................................................................................................................................................2
2.4 Pad Mounting...................................................................................................................................................................................................................................................................3
2.5 Wiring.......................................................................................................................................................................................................................................................................................3
2.6 Power........................................................................................................................................................................................................................................................................................3
2.7 Power Indicator Lights.............................................................................................................................................................................................................................................3
2.8 Door and Lock .................................................................................................................................................................................................................................................................3
2.9 Opening the Door .........................................................................................................................................................................................................................................................3
2.10 Normal/Generator Power Relays....................................................................................................................................................................................................................3
3 Site Selection and Preparation ..................................................................................................................................... 5
3.1 Site Selection Considerations............................................................................................................................................................................................................................5
3.2 Equipment Life Span .................................................................................................................................................................................................................................................5
3.3 Easements and Rights-of-Way.........................................................................................................................................................................................................................5
3.4 Safety........................................................................................................................................................................................................................................................................................5
3.5 Obstruction.........................................................................................................................................................................................................................................................................5
3.6 Likelihood of Damage...............................................................................................................................................................................................................................................5
3.7 Distance from Other Objects.............................................................................................................................................................................................................................5
4 Transportation and Storage .......................................................................................................................................... 5
4.1 Field-Installed Units....................................................................................................................................................................................................................................................5
4.2 Inspecting the Packaging......................................................................................................................................................................................................................................5
4.3 Correct Shipping and Storage ..........................................................................................................................................................................................................................5
5 Grounding............................................................................................................................................................................ 5
5.1 Grounding Standards ................................................................................................................................................................................................................................................6
6 Mounting the Cabinet on a Pad.................................................................................................................................... 6
6.1 Before You Begin...........................................................................................................................................................................................................................................................6
6.2 Constructing the Pad................................................................................................................................................................................................................................................8
6.3 Mounting the Cabinet on the Pad...............................................................................................................................................................................................................11
7 Mounting the Cabinet on a Pole..................................................................................................................................12
7.1 Pole-Mount Kits............................................................................................................................................................................................................................................................12
7.2 Height on Pole...............................................................................................................................................................................................................................................................12
7.3 Pole Installation.............................................................................................................................................................................................................................................................12
8 Mounting the Cabinet on a Wall ................................................................................................................................. 14
8.1 Solid Bottom ...................................................................................................................................................................................................................................................................14
8.2 Wall Installation............................................................................................................................................................................................................................................................14
9 Meter Options ...................................................................................................................................................................15
9.1 Factory-Installed Meters......................................................................................................................................................................................................................................15
9.2 Supplying Your Own Meter................................................................................................................................................................................................................................15

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
iv
10 DC Power, Outdoor Enclosure & Service Contacts...............................................................................................16

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
v
Admonishments Used in this Document
DANGER
! Warns of a hazard the reader will be exposed to that will likely result
in death or serious injury if not avoided
. (ANSI, OSHA)
WARNING
! Warns of a potential hazard the reader may be exposed to that could
result in
death or serious injury if not
avoided. This admonition is not used for situations that pose
a risk only to equipment, software, data, or service
. (ANSI)
CAUTION
! Warns of a potential hazard the reader may be exposed to that could
result in minor or moderate injury if not avoided
. (ANSI, OSHA) This admonition is not
used for situations that pose a risk only to equipment, data, or service, even if such use
appears to be permitted in some of the applicable standards
. (OSHA)
ALERT
! Alerts the reader to an action that must be avoided in order to protect
equipment, software, data, or service
. (ISO)
ALERT
! Alerts the reader to an action that must be performed in order to prevent
equipment damage, software corruption, data loss, or service interruption
. (ISO)
FIRE SAFETY
! Informs the reader of fire safety information, reminders, precautions,
or policies, or of the locations of fire
-fighting and fire-safety equipment. (ISO)
SAFETY
! Informs the reader of general safety information, reminders, precautions, or
policies not
related to a particular source of hazard or to fire safety. (ISO, ANSI, OSHA)

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
vi
Important Safety Instructions
Safety Admonishments Definitions
Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this Document” on page v.
You Must Follow Approved Safety Procedures
DANGER! Performing the following procedures may expose you to hazards. These procedures should be performed by
qualified technicians familiar with the hazards associated with this type of equipment. These hazards may include shock,
energy, and/or burns. To avoid these hazards:
a) The tasks should be performed in the order indicated.
b) Remove watches, rings, and other metal objects.
c) Prior to contacting any uninsulated surface or termination, use a voltmeter to verify that no voltage or the expected
voltage is present. Check for voltage with both AC and DC voltmeters prior to making contact.
d) Wear eye protection.
e) Use certified and well maintained insulated tools. Use double insulated tools appropriately rated for the work to be
performed.
Buried Utilities
CAUTION! When installing the enclosure, ensure the site is free of any buried utilities. Call 811 before installation. Severe
damage, serious injury, or death can occur if buried utilities are not identified prior to installation.
Personal Protective Equipment (PPE)
DANGER! ARC FLASH AND SHOCK HAZARD.
Appropriate PPE and tools required when working on this equipment. An appropriate flash protection boundary analysis
should be done to determine the “hazard/risk” category, and to select proper PPE.
Only authorized and properly trained personnel should be allowed to install, inspect, operate, or maintain the equipment.
Do not work on LIVE parts. If required to work or operate live parts, obtain appropriate Energized Work Permits as required
by the local authority, per NFPA 70E “Standard for Electrical Safety in the Workplace”.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
1
1About this Document
This practice provides a description of the Vertiv XTE PTS Series PEIL/PESB Power Transfer Switches as well as installation
instructions.
2Description
2.1 Application
The XTE PTS Series PEIL/PESB Power Transfer Switches (shown in Figure 1and Figure 2) provide weatherproof housing and surge
protection for the electrical components that transfer/distribute commercial and generator power. They have a wide range of
standard features and options to suit a variety of applications.
Figure 1: Power Transfer Cabinet

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
2
Figure 2: Power Transfer Cabinet (Exploded View)
2.2 Cabinet Dimensions
The dimensions of both the XTE PTS Series PEIL/PESB Power Transfer Switches are:
-height: 433/16 inches (109.7 cm)
-width: 213/8 inches (54.3 cm)
-depth: 9 inches (22.9 cm)
NOTE! When a meter is added, the height from the bottom of the cabinet to the top of the meter is 6011/16 inches (154.1 cm).
2.3 Construction
The XTE PTS Series PEIL/PESB Power Transfer Switches are manufactured from heavy gauge aluminum finished with a durable paint
process that meets Telcordia specifications for protection against corrosion, water intrusion, ultraviolet radiation, and impact
resistance. They are available in off-white, green, or brown to suit most residential and commercial environments.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
3
2.4 Pad Mounting
The XTE PTS Series PEIL/PESB Power Transfer Switches may be mounted directly to a concrete pad. A metal mounting template is
available that can be used to orient the mounting bolts and incoming and outgoing power conduit in the pad.
2.5 Wiring
The XTE PTS Series PEIL/PESB Power Transfer Switches are fully wired and are UL Listed. See Figure 3.
2.6 Power
A load center in the XTE PTS Series PEIL/PESB Power Transfer Switches distributes electrical power and has twelve available breaker
positions. A standard 15 Amp 120V GFI (Ground Fault Circuit Interrupter) or convenience outlet (or a 20 Amp GFI on 22,000 AIC
cabinets) allows craft personnel to plug into the PEIL/PESB power transfer cabinet when AC power is required for field service and
maintenance. The GFI uses one load center position.
2.7 Power Indicator Lights
Dual indicator lights show both polarities of power which indicates the presence of active commercial power inside the power transfer
enclosure, or shows loss of power to one or both phases.
2.8 Door and Lock
The XTE PTS Series PEIL/PESB Power Transfer Switches have a three-point locking mechanism that is secured with a padlock hasp.
Additional door handle locking options include a hex-head lock or a pin hex-head lock. Wind latches on the cabinet secure the door in
an open position.
2.9 Opening the Door
To open the door, lift up on the handle, and turn it 90° clockwise.
2.10 Normal/Generator Power Relays
The Utility/Generator relay indication assembly is designed to alarm the user when Normal power is interrupted. The setup is
designed so that when a generator is placed on-site, the Network Operations Center (NOC) will get an indication that the generator is
running. When Normal power is returned, the alarm will also indicate the change of states and the technician can return to the site
and remove the generator.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
4
Figure 3: Example of Internal Wiring of a Power Transfer Cabinet

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
5
3Site Selection and Preparation
3.1 Site Selection Considerations
Consider the following when choosing a location for a XTE PTS Series PEIL/PESB Power Transfer Switch.
3.2 Equipment Life Span
A permanent location is desirable. Your planning and the hardware used should accommodate at least a thirty-year life.
3.3 Easements and Rights-of-Way
In advance of construction, the installing company should acquire the rights-of-way from landowners and permits or other approvals
from public authorities. It is recommended that the cabinet be placed in servitudes, on dedicated (recorded) easements, or on
property owned by the company. If possible, avoid unrecorded easements.
3.4 Safety
Use public safety road and street rights-of-way only when there is adequate space to place the enclosure and to provide safe working
conditions. The enclosure should be easily accessible with adequate space for craft personnel parking.
3.5 Obstruction
Place the enclosure where it will not create a visual or physical obstruction to either vehicles or pedestrians.
3.6 Likelihood of Damage
Choose a location that minimizes the vulnerability of the enclosure to vandalism and other damage. Use protective posts when the
enclosure is placed near parking areas where vehicles could hit it.
3.7 Distance from Other Objects
Place the enclosure so that it is at least 42 inches (107 cm) away from any obstruction, fence, hedge, etc.
4Transportation and Storage
4.1 Field-Installed Units
All enclosures can be purchased for field installation, which are shipped on a special pallet for easy movement and storage.
4.2 Inspecting the Packaging
When the cabinet arrives, visually inspect the packaging for damage. If the packaging appears damaged, do not accept the power
cabinet from the shipper, as interior damage may have occurred.
4.3 Correct Shipping and Storage
To avoid possible damage to the unit, always ship and store the cabinet in an upright position.
5Grounding
DANGER! ELECTRICAL HAZARD
The grounding rod must be installed before the cabinet is installed:

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
6
5.1 Grounding Standards
The customer is responsible for providing and installing a ground rod. When installing the ground rod, keep the following in mind:
Minimum standard grounding configuration is one point. For other grounding configurations, consult local building codes.
All materials must be UL approved and meet NEC codes. The ground rod should be copper. It should be 8 feet (2.4 m) long and 5/8
inch (1.6 cm) in diameter.
The rod should be placed according to local building codes and should be located near the XTE PTS Series PEIL/PESB Power
Transfer Switch. (Refer to Figure 5for location).
6Mounting the Cabinet on a Pad
DANGER! ELECTRICAL HAZARD
Electrical hazard. Do not install the cabinet during a thunder storm. All power must be turned off before removing inner
barrier panels.
6.1 Before You Begin
Local Practices
A XTE PTS Series PEIL/PESB Power Transfer Switch may be installed on a separate concrete or preformed fiberglass pad or on a
remote terminal pad. This practice provides instructions for constructing a typical concrete pad. However, you may vary your
construction methods to comply with local conditions, practices, or building codes.
Accessory Kit
An accessory kit is shipped in a cardboard box with the XTE PTS Series PEIL/PESB Power Transfer Switch. This kit includes washers,
a meter hub, and a hard rubber gasket. During installation, the rubber gasket is sandwiched between the pad and the cabinet base to
eliminate corrosion.
Additional Materials Needed
You will need to supply the following materials to construct a concrete pad for a XTE PTS Series PEIL/PESB Power Transfer Switch:
•electrical conduit (consult your local building department for size),
•ground wire (No. 6 AWG is recommended),
•framing materials with which to form the pad,
•No. 66-44 wire mesh sized to fit the pad, and
•concrete that conforms to A.S.T.M. 94 specifications for ready-mixed concrete.
Mounting Template
An aluminum mounting template (shown in Figure 4) with anchor J-bolts may be used to provide the cabinet mounting position and
conduit access holes. The template kit (Part No. PEIL/RPEIL-TEMP) must be ordered separately.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
7
Figure 4: Metal Mounting Template
.000
.000
3holes
0.625in.(1.59cm)
2 holes
0.203 in. (5.2 mm)
1 hole
0.375 in. (9.5 mm)
through andin line
2.73 in. (6.93 cm) 8 in.
(20.32 cm)
8in.
(20.32 cm)
4 holes
0.562 in.
(1.43 cm)
4 holes
1.375 in.
(3.49 cm)
slot
3 by 6 in.
(7.62 by 15.24 cm)
2 holes
2.5 in. (6.35 cm)
2 holes
3 in. (7.62 cm)
1hole
0.375 in. (9.5 mm)
through and in line
0.375 in. (9.5 mm)
1in./2.54 cm (TYP)
4.376 in. (11.115 cm) REF
1.376 (3.495 cm) REF
7.408 in. ± 0.030 in.
(18.816 cm ± 0.76 cm)
2X 6.235 in. (15.837 cm)
2
X 5.376 in. (13.655 cm)
2X 4.689 in. (11.91 cm)
3X 2.876 in. (7.305 cm)
2X 2.126 in. (5.4 cm)
2X 1.173 in. (2.979 cm)
2x 0.953 in. (2.42 cm)
2.703 in. (6.866 cm)
3.422 in. (8.692 cm)
2X 6.016 in. (15.281 cm)
7.703 in. (19.566 cm) REF
10.703 in. (27.186 cm)
1
3.703 in. (34.806 cm) REF
2X 15.391 in. (39.093 cm)
17.984 in. (45.679 cm)
18.703 in. (47.506 cm)
2X 20.453 in. (51.951 cm)
21.406 in. ± 0.030 in.
(54.371 cm ± 0.076 cm)
3.704 in.
(9.408 cm)
7.408 in.
(18.816 cm)
REF
2 holes
0.875 in. (2.22 cm)

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
8
6.2 Constructing the Pad
Stages of Construction
•The construction of the pad is performed in the following stages:
•Preparing the Site
•Preparing to Pour the Concrete,
•Installing the Mounting Template,
•Pouring the Concrete.
Preparing the Site
Perform the following steps to prepare the site for construction of the concrete pad:
1. Make sure that the pad location is firm and level. If the ground around the location is not firm, compact the soil and construct
a level base for the pad using a minimum of 6 inches (15 cm) of gravel.
2. Dig trenches to accommodate the conduit for AC power cable and the ground wire according to local practices. See Figure
5, Figure 6, and Figure 7for the conduit entrance location.
3. Place the conduits for AC power cable. Conform to local electrical construction standards for conduit materials and sizing.
4. If required by local practices, treat the area below the pad and for 2 feet (60 cm) around the perimeter against insect
infestation.
5. Fill in the trenches around the pad with soil and tamp.
Preparing to Pour the Concrete
Perform the following steps to form the pad and to prepare for the pouring of the concrete:
1. Construct the pad forms, using the dimensions shown in Figure 5, Figure 6, and Figure 7.
2. Place wire mesh in the forms so that the mesh is vertically centered in the finished pad. (See Figure 5, Figure 6). Make sure
that the wire mesh or reinforcing bars are set approximately 2 inches (5 cm) off the bottom of the form.
NOTE! In place of wire mesh, you may use No. 3 (3/8-inch - 9.5 mm) or larger reinforcing rods placed on 15-inch (38.1 cm)
centers.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
9
Figure 5: Conduits
Figure 6: Pad Construction and Preparation
utility
service
conduit
grade
ground rod
approximately 3 in.(8 cm)
6 in.
(15.24cm)
approximately
5 in. (13 cm)
conduit exiting
toward site
No.66-44wire mesh
orequivalent

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
10
Figure 7: Mounting Template Installation
Installing the Mounting Template
If you are using the mounting template kit (part number PEIL/RPEIL-TEMP), then perform the following steps to install it:
1. Verify that all components (listed in Table 1) are included in the kit:
Table 1: Contents of Mounting Template Kit
Quantity Description
1 Template
4 1/2-13x6-inch (15.24 cm) J-bolts
8 1/2-13 nuts
8 1/2-inch flat washers
2. Install one of the 1/2-13 nuts on each J-bolt. Thread the nut down, leaving approximately five threads below the nut.
3. Slide one flat washer on each J-bolt.
4. Slide each J-bolt through the 9/16-inch (1.43 cm) hole on the template.
5. Install a flat washer onto each J-bolt on the top side of the template., then install a nut.
6. Turn the J-bolts outwards, toward the front and back sides of the template, then tighten the nuts.
3-inch (7.6 cm) hole for 21/2-inch (6.4 cm)
incoming power company service
conduit for the RPEIL Series cabinet
4 1/2-13 by 6-inch (15.24 cm)
J-bolts, turned outwards to the
front and back of the template,
to mount the template to the pad
Form is constructed
of 2 by 6-inch (5
by 15 cm) boards.
front of
cabinet
3 by 6-inch (7.6 by 15.2 cm)
slot, 2 21/2-inch (6.4 cm)
holes, and 4 13/8-inch (3.5 cm)
holes for outgoing power
to power
end chamber
3-inch (7.6 cm) hole for 21/2-inch (6.4 cm)
incoming power company service
conduit for the PEIL Series cabinet
Secure template to
stakes and level before
pouring concrete.
Top surface of template
should be level with top
surface of form and flush
with concrete surface.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
11
NOTE! The 3-inch (7.6 cm) hole at the back-left side of the template is used for incoming power conduit for RPEIL-series
cabinets. The 3-inch (7.6 cm) hole at the back-right side of the template is used for incoming power conduit for the PEIL-
series cabinets.
7. Place the mounting template into position in the pad form as shown in Figure 7.
8. Fasten the mounting template to the wooden stakes.
9. Level the mounting template on the stakes so that the top of the plate is flush with or slightly above the top of the pad.
10. Allow the conduits to extend above the template approximately 3 inches (8 cm). Make sure that each conduit extends
vertically through the template, perpendicular to the hole.
Pouring the Concrete
Perform the following steps to pour the concrete:
1. Cover the conduit openings to keep wet concrete from entering them.
2. Pour concrete into the forms until level or slightly above the forms.
3. Puddle the concrete along the edges of the forms, then use a straight piece of lumber or equivalent to level the concrete.
4. If not using the mounting template, then before the concrete hardens, install locally provided screw anchors with 1/2-13
threads. Place them in the pad using the dimensions shown in Figure 4and Figure 6.
5. For additional finishing, wait until the pad no longer looks as if water is standing on top of it, and trowel the concrete smooth.
6. In a moist environment, allow the concrete to cure for a minimum of seven days. You may remove the forms after the second
day.
7. If you are installing screw anchors after the concrete has hardened, then perform the following steps to install them:
•Obtain expansion-type anchors with 1/2-13 threads.
•Determine the proper hole size based on the size and type of your expansion-type anchors.
•Drill holes in the pad. See Figure 4and Figure 6for the proper placement of the holes.
•Insert the expansion-type anchors into the holes.
6.3 Mounting the Cabinet on the Pad
Perform the following steps to mount the cabinet on the pad:
1. Before placing the cabinet, verify that the pad has been prepared and the conduit for electrical feed and distribution cabling
has been installed according to local electrical codes and practices.
2. Open the door, and secure the wind latch located in the bottom left corner.
3. Place the rubber gasket on the pad over the conduit and the template. If you are not using the template, then place the
rubber gasket over the conduit in the pad so that the cabinet will be properly positioned on it. (See Figure 6.)
4. Using proper lifting procedures, place the cabinet in the mounting position on the pad.
5. Secure the cabinet to the pad using the rubber gasket, the hardware from the template, or customer-supplied 1/2-inch (1.3
cm) bolts or nuts that mate with the hardware used in the concrete pad.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
12
6. Torque between 500 and 550 inch-pounds (56.54 and 62.2 Kilogram-Meters).
7. Have a licensed electrician complete the electrical hookup to the power meter and to the load center according to electrical
codes and procedures. Refer to the wiring diagram in Figure 3, which is also located on the inside of the cabinet door, for
interior wiring connections.
8. After the wiring is complete, fill the pad opening with pea gravel until flush with the top of the pad.
9. Close the door and secure it.
7Mounting the Cabinet on a Pole
DANGER! ELECTRICAL HAZARD
Do not install the cabinet during a thunder storm. All power must be turned off before removing inner barrier panels.
To avoid possible injury or damage to equipment, follow all local safety practices and wear appropriate safety gear when
installing the cabinet on a pole.
7.1 Pole-Mount Kits
Standard pole-mount kits must be ordered separately. These kits are designed for use on wooden poles. The part numbers for the
pole-mount kits are as follows:
•Brown: PEIL-PB-Kit
•Off-White: PEIL-PI-Kit
•Green: PEIL-PG-Kit
NOTE! Mounting hardware is not provided. You must supply two 1/2-inch (1.27 cm) bolts suitable for the pole size.
7.2 Height on Pole
The cabinet can be installed at any height on the pole. For ease of access, install the cabinet at working level or in accordance with
local practices.
NOTE! Make sure that there is enough clearance to maintain the minimum bend radius of the cable to be installed.
7.3 Pole Installation
Perform the following steps to install a XTE PTS Series PEIL/PESB Power Transfer Switch on a pole using a standard pole-mount kit:
1. Unpack the pole-mount kit and the cabinet.
2. Verify that the Pole-Mount kit contains the following components (as shown in Fig. 8):
•a two-point pole-mount channel,
•two aluminum washer plates,
•two rubber gaskets to be installed between the cabinet and the aluminum washer plates, and
•a solid bottom.

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
13
NOTE! Mounting hardware is not provided. You must supply two 1/2-inch (1.27 cm) bolts suitable for the pole size.
3. Dispose of the packaging according to local practices.
4. Place the pole-mount channel in the mounting position on the pole.
5. Use the pole-mount channel as a template to drill two mounting holes that will accommodate the two 1/2-inch (1.3 cm)
mounting bolts.
6. Open the cabinet door.
7. Remove the two 3/4-inch (1.9 cm) knockouts from the back of the cabinet. (See Figure 8).
Figure 8: Pole-Mount Kit
8. For each of the two bolts, slide one of the washer plates over one of the 1/2-inch (1.3 cm) mounting bolts and then slide one
of the rubber gaskets over the bolt.
9. Install each bolt with its washer plate and gasket into the 3/4-inch (1.9 cm) knockout holes in the cabinet. (See Figure 8).
10. Install the pole mount channel to the cabinet over the mounting bolts. (See Figure 8).
pole mount
channel
3/4-inch (1.9 cm)
knockouts
aluminum washer
plate
rubber gasket
solid bottom
rear view

Vertiv™ XTE PTS Series PEIL/PESB Power Transfer Switches Description & Installation Manual
14
CAUTION! Make sure that the cabinet is supported by the lifting equipment during the installation.
11. Using appropriate lifting equipment and following all local safety procedures, lift the cabinet and bracket into mounting
position on the pole.
12. Level the cabinet before tightening the bolts, then tighten the bolts to secure the bracket and cabinet to the pole.
13. Remove the open bottom from the cabinet, and set the hardware aside.
14. Install the solid bottom from the pole-mount kit using the hardware saved in the step above.
8Mounting the Cabinet on a Wall
DANGER! ELECTRICAL HAZARD
Do not install the cabinet during a thunder storm. All power must be turned off before removing inner barrier panels.
8.1 Solid Bottom
A wall-mounted cabinet should have a solid bottom, rather than the open bottom supplied with pad-mounted cabinets. If the cabinet
does not have the solid bottom, order the solid bottom, and replace the standard open bottom with the solid bottom using the
hardware provided.
8.2 Wall Installation
Perform the following steps to install a XTE PTS Series PEIL/PESB Power Transfer Switch on a wall:
1. Unpack the cabinet.
2. Verify that the loose parts kit contains the following components:
-two 1/2-inch (1.3 cm) sealing washers, and
-two flat washers.
NOTE! Mounting hardware is not provided. You must supply two 1/2-inch (1.27 cm).
3. Remove the four 1/2-inch (1.3 cm) knockouts from the back of the cabinet. (See Figure 9.)
CAUTION! Make sure that the cabinet is supported by the lifting equipment during the installation.
4. Use appropriate lifting equipment to raise the cabinet into the mounting position on the wall, and keep it supported.
5. Use the cabinet as a template to drill four mounting holes. (See Figure 9).
6. If anchors are being used, remove the cabinet, and install the anchors.
7. Slide the two sealing washers onto the two top bolts, with the metal facing toward the head of the 1/2-inch (1.3 cm) bolt. (See
Figure 9).
8. Install the two flat washers onto the two bottom bolts.
9. Install a bolt with its washer into each of the four 1/2-inch (1.3 cm) knockout holes in the cabinet, then into the wall or other
mounting structure. (See Figure 9).