Viavi OneExpert CATV 630 User manual

Extended Quick Start Guide v4
August 2019
OneExpert
CATV 630

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 2
Table of Contents – OneExpert CATV
ONX CATV – Interfaces and Controls
System Settings
CATV Settings
SW Upgrade and Data Synchronization
Firmware Upgrades
Synchronization with StrataSync
Ethernet Testing
CATV Measurements
QuickCheck
Spectrum
TDR
HL Leakage Option and Transmitter
Ingress Scan
Channel Check
DOCSIS Check
OneCHECK
D3.1 Measurements
CATV NETWORK Measurements
Configure Screens
QuickCheck EXPERT
Channel EXPERT
DOCSIS EXPERT
Ingress EXPERT
Return Signal Generator (RSG) w/
Loopback
Forward and Return Sweep
Sweepless Sweep

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 3
Support Links
Viavi Customer Care:
For questions about warranty information, repair and calibration, Return
Material Authorization (RMA) request, services quotation, order status.
T: 1-844 GO VIAVI ([phone])
E: NAM.Customer[email protected]
https://www.viavisolutions.com/en-us/services-and-support/support-
center/customer-care
Customer Care Portal Login
https://www.viavisolutions.com/en-us/services-and-support/support-
center/customer-care/customer-portal-login
RMA Request Form:
http://www.viavisolutions.com/en-us/services-and-support/return-
material-authorization-rma-request
Viavi Technical Support:
Will assist you in using/configuring products or address issues regarding
product performance.
T: +1-844 GO VIAVI ([phone])
E: [e-mail]
For access to online technical and product support:
http://support.viavisolutions.com
Quick Tip Videos (including ONX):
https://www.viavisolutions.com/en-us/support/quick-references/quick-
tip-videos
Product Focused YouTube Channel:
ViaviSolutions CIVT

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 4
4© 2018 VIAVI Solutions Inc.viavisolutions.com
ONX CATV - Overview

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 5
ONX Control keys
Network Indicator LEDs
High Sensitivity Touch Screen
Shortcut Buttons
Short Cut Hard keys – Functions keys
Navigation Directional Buttons
Back, Home Screen, and Utility Buttons
Power On/Off Button

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 6
ONX Interfaces Port 2 – RF Ingress Port
Connect to
upstream from house
for Ingress Scan
Port 1 – RF US/DS Analysis
DOCSIS, QAM
D-Ring
Dual 10/100/1000
RJ45 Ports
Dual USB 2.0 Ports
Battery Charger Port (under flap)
D-Ring

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 7
Power LED and Systems Keys
The DC Power Input, located on the bottom
of the instrument, is used to connect the AC
adapter.
The Charge LED located next to the power
input indicates that the adapter is connected.
Solid green indicates that charging is
complete.
Slow flashing red indicates that the battery
charge is critically low, and less than 10%.
Fast flashing red indicates that the charging
was suspended due to a fault and user
intervention is necessary (for example, an
incorrect charger is attached).
Solid red indicates that the charging was
suspended due to overheating. The unit can
continue to run, and no user intervention
necessary.
Solid amber indicates that the battery is
charging.

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 8
LED’s Sync – Reports the status of modem synchronization.
Blinking green indicates that the modem is ranging.
Solid green indicates that the modem has
successfully ranged.
Network –Indicates the status of network
connectivity.
Blinking green indicates that the unit is acquiring
an IP address.
Solid green indicates that an IP address has been
acquired.
Blinking amber indicates a timeout – the unit was
unable to acquire an IP address.
If the LED is not illuminated, the network is not
active – either the unit is not connected or it is
logged off.
Batt –A multi-color LED that indicates the battery
status.
Solid green indicates that either the battery charge
is higher than 30%, or that an external source is
powering the unit.
Solid red indicates that the battery charge is
critically low, and less than 10%.
Solid amber indicates that the battery is getting
low, and the charge is between 10% and 30%.
Error –Solid red indicates error and
alarm conditions. The type of error
varies and depends on the
application.

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 9
Tray Menu
SAVE TO JOB – Saves the results to job ticket.
SAVE TO REPORT – Saves the results to a
report. Formats available: XML, PDF, or HTML.
VIEW REPORT – Views a saved report. Select
View Report and then select the saved report to
view. If there are no saved reports, the text will
be grayed out.
SCREENSHOT – Takes a screen capture of the
current menu (the screen you were viewing
when you launched the tray menu).
NETWORK – Enables or disables the
home/Ethernet network.
BLUETOOTH – Enables or disables Bluetooth.
VOLUME – Control the device volume.
HELP – Provides TAC phone numbers.
USING THE TRAY MENU
The tray menu allows access to
commonly used functions. It can
be accessed either by pressing the
Tray system key or by swiping
downward from the top of the LCD.
Hint:
A long push on TRAY key will
automatically start a screen capture. It is
useful when a short Tray key push
doesn’t open the Tray menu (when for
example a function key menu is open)

© 2017 Viavi Solutions, Inc. | Viavi Confidential and Proprietary Information 10
User interface
SELECTING A MENU
To select a menu, either touch the item or use the arrow
navigation keys to highlight the desired menu item and
then press the OK key.
SHORTCUTS
If you have a test or function that you use
frequently you can make it a shortcut.
Touch and hold the icon for the function and then
drag it to the bottom of the screen to create a
shortcut.
You can create up to four shortcuts.
To remove the shortcut, drag it off the shortcut bar.
REARRANGING ICONS
You can rearrange icons within a menu for tests
or functions you use frequently.
To rearrange icons inside a menu, touch and
hold the icon and then drag it to the new
location.
COLLAPSIBLE MENUS
Each main item is a collapsible menu. Touch the
triangle on the right (the triangle rotates from
pointing left to pointing down) or use the arrow
keys to highlight the menu item and then press
the OK key.