Viavi SmartOTDR Parts list manual

SmartOTDR GETTING STARTED MANUAL
 
Laser safety
The provisions contained in two standards dene the safety procedures to be observed both by users and
by manufacturers when utilizing laser products:
-EN 60825-1: 2001 - Safety of laser products – Part 1: Classication of products, requirements and user
guidelines.
-FDA 21 CFR § 1040.10 - Performance standards for light-emitting products - Laser products.
Due to the range of possible wavelengths, power values and injection characteristics of a laser beam, the
risks inherent in its usage vary. The laser classes form groups representing different safety thresholds.
-VFL option: Laser Class 2.
Due to the reduced dimensions of the optical modules, it is not possible to attach the required warning la-
bels to them. In line with the provisions of Article 5.1 of the EN 60825-1 standard, the laser class identica-
tion labels are shown below:
Ref. standard EN 60825-1, Edition 1.2, 2001-08 FDA21CFR§1040.10
Class 2
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASER RAD IATION - DO NOT
STARE INTO BEAM
CLASS II LASER PRODUCT
CAUTION
The user must take the necessary precautions concerning the optical outputs of the instrument and
follow the manufacturer’s instructions.
AC/DC power supply safety
!
Always use the proper adaptable plug to connect the power supply to an electrical outlet. Viavi is
not responsible for direct or indirect damage including damage to persons or property if the power
supply is not use correctly. For assistance using one of the Viavi supplied adapters (your specic
regional adapter may not be available) please refer to the user manual.
   
Before connecting a ber into a test module, inspect and clean the module bulkhead and the ber jumper
connectors.
1
Use a video inspection scope (such as P5000i) to verify the connector quality. Follow this simple
“INSPECT BEFORE YOU CONNECT” process
2
Use appropriate cleaning material (e.g. IBC™ cleaner, cotton swab, dust air sprays, etc...) and
re-inspect to conrm.
3
Carefully align the connector and test port prior to mating both
Never force the connector ferrule or insert it with an angle into the test port adapter. Mechanical stress
may permanently damage the ceramic sleeve of the adapter or the end face of the connector.
     mart
2
On the Home page, select the Microscope icon.
3
Use Focus control button on Microscope to
adjust focus.
4
Congure the test of the connector.
7
A summary of test results is displayed.
Zones: A - Core / B - Cladding / C - Epoxy /
D - Ferrule
1
Connect the Microscope to the SmartOTDR USB
port.
SETUP
5
Press
RESULTS
to return to Results page
Congure the le storage
6
Display information
on scope & current
test result displayed
mart 
1 5’’ HVT Capacitive Screen 8 On/Off
15
Slave Mini USB port
2 Charge indicator 9 Home page
16
VFL connector
3 On indicator
10
Cancel (switch off functions)
17
USB ports (2)
4 File menu
11
Direction & validation keys
18
OTDR port / continuous light
source / power meter
5 Setup menu
12
Results page
6 Start/Stop
13
Buzzer
19
OTDR live port (in-service test)
7 Testing indicator
14
AC/DC Input
20
WIFI or Bluetooth options
15
14 18 1916 17
1
1312111098
765432
20
      mart est 
2
From the Results page, press .
SETUP
1
On the Home page, select Smart TEST icon . Step1: connector check
Step2: acquisition in progress
4At the end of test,
the results trace displays.
A
B
C
D
E
STaRT/SToP
ATrace: select the active trace (multi-traces analysis)
Summary: display a summary of results for each
wavelengths
SmartLink (optional): Icon based map view
BZoom and shift on trace
CAllows to modify some acquisition parameters and
load Smart Cong.
D Save in a sor le and create a txt or pdf report of
the results
EToggle between Table of results <-> Fault Locator
View
3
Allows to load an existing congura-
tion le (Smart Cong.)

SmartOTDR - Getting Started Manual - PN7SMART202 Rev002 - November 2015 - Copyright © 2015
   /   mart onfig.   
3
Congure the OTDR parameters.
4
Select one parameter and press to
save the current conguration
5
Press to access the conguration le
2
From the Results page, press .
FILE
summary of conguration parameters into the le
To perform acquisitions in Expert OTDR, see chapter “Launching a reectometry test and displaying
results” in Module User Manual.
1
On the Home page, select ExpertOTDR .
SETUP
      
Sub-directory created
1
Once results are displayed, press to
display the le Explorer.
2
Select the location where the directory must be
created.
3
Press
4
Enter a name for the new directory.
The traces acquired can be saved in the new directory.
FILE
Storage media
selected
The les can be transferred, using Edit sub-
menu:
-to USB folder if plugged
-to your remote device via Bluetooth
-to your preferred cloud storage server
To get more information on Connectivity and
les transfer, refer to SmartOTDR Base Unit
User Manual.
   
1
In the Results screen, press Fast Report key.
2Select the Save Mode and , if necessay, modify
the Fiber / Cable / Link parameters:
File Only: save exclusively the OTDR trace(s)
File + txt: save the OTDR trace(s) & generate a txt le
File + pdf: save the OTDR trace(s) & generate a pdf le
All: save the OTDR traces & generate a pdf and a txt le
4
In the edition keypad, enter the lename or
press Auto Filenaming menu key.
5
Press to validate
3
Press
FILE
Once saving is completed, the le(s) is/are dis-
played in the Explorer.
 
4
Press Select once the desired network to
connect to is selected, via WIFI.
In setup page, the SSID parameter is automatically
congured with the one selected
6
Press to connect the congured SSID.
On the upper banner, the icon WIFI “inactive”
turns active .
To get information on WIFI use, refer to SmartOTDR Base Unit User Manual.
1
On the Home page, select > .
2
In Setup page, press Wireless key and congure
the WIFI connection in Conguration box.
5
Congure
7
To work on WIFI with the
Platform, congure the
802.11 parameters, and the
proxy parameter if necessary
8
Note the IP address of the SmartOTDR to be able
to remote screen on PC or to transfer les via WIFI
3
 
If you require technical assistance, call 1-844-GO-VIAVI. For the latest TAC information, go to http://www.
viavisolutions.com/en/services-and-support/support/technical-assistance.
Press