VIBIA Halley User manual

Halley
Design by Jordi Vilardell & Meritxell Vidal
ASSEMBLY INSTRUCTIONS
SUPPLIED MATERIAL
TECHNICAL SPECIFICATIONS
4190 4195
1 Tube of thermal grea e 1 un. 1 un.
2 Allen key 1 un. 1 un.
3 Lamp tructure 1 un. 1 un.
4190.
Net Weight 1,5 Kg
1 x LED STRIP 24V 5,7W
4195.
Net Weight 1,3 Kg
1 x LED STRIP 24V 2,8W
Cla I. Product with an additional protection cable (ground ).
Du t-tight product. Protected again t water trickle .
Product that CAN be in contact with normally-flammable
material (wood or other ).
-If the teel cable or the power cord of thi lamp i damaged, it mu t be replaced only by the manufacturer or their technical ervice or by a per on capacitated to thi effect to avoid
any ri k.
-We recommend reading the manual before in tallaing the lamp. Keep thi in truction for future reference.
Caution
Be ore assembling and installing this product, care ully read the ollowing:
-Switch of the main before in talling the lamp.
2.
3.
4190.
4195.
1.

ASSEMBLY INSTRUCTIONS
1.
Make a hole in the ground of Ø13.5cm and 18.5cm deep to et the
ca ing (B) into, and provide a gravel drainage y tem 20-30cm deep
if the ground i andy. If the lamp i to be et into concrete, provide
for the mo t uitable drainage y tem.
IMPORTANT: Carry out a trial by filling the hole with water and
waiting 30 minute ; if the water ha not drained away completely by
thi time, fit an extra drainage y tem.
2. Remove the three crew (A) y extract the part (B).
3. In ert the ca ing (B) in the re ulting hole, running the power cable
(C) through in ide it and fill the hole to make it even with the
urrounding urface. Enough length of cable mu t tick out above the
ground to make the power connection.
NOTE: Before filling in with cement, make ure the threaded hole in
the top are in the right po ition for the light fitting to face in the
de ired direction once in talled.
IMPORTANT NOTICE:
Caution : to avoid possible electrical shock, make certain
electricity is shut o at main panel be ore wiring
B
A
C
B
3
2
Ø13,5 cm.
18,5 cm.
20 - 30 cm.
Main power cable
Gravel for drainage
1
Extra drain pipe

Maintenance
-U e a lightly-wet cotton cloth for cleaning.
-In ca e of malfunction or damage, plea e contact the retailer who old the lamp.
ASSEMBLY INSTRUCTIONS
6
7
4
C
G
E
FD
EH
5
D
B
A
8
4.
Connect to the main :
Step 1: Remove the 4 crew from the wiring box and open up
the cover (D).
Second: Loo en the cable gland (E) in order to in ert the cable
(C) into the wiring box.
Third: Make the electrical connection, pha e+neutral in the box
(F) and grounding to the terminal (G).
IMPORTANT: Thi model i ready for direct connection to an IP
65-cla power point. The cable u ed mu t be H05 RN-F
<HAR> or better rubber, between 7 and 12mm in diameter.
5. After making all the connection , tighten up the cable gland
(E) firmly once more. You are advi ed to eal where the main
power cable enter the box a hown in the drawing, u ing the
yringe of thermal ilicon grea e upplied (H).
6. Fit the cover (D) with the 4 crew and remember to tighten
the cable gland to en ure it i ealed.
7. In ert the clo ed connection box and adju t the cable in ide
the part (B).
8. Fix in place u ing the three crew (A).