Vimar ELVOX 7559 User manual

Installation and operation manual
TAB
7559
TAB 4.3 Due Fili Plus hands-free video entryphone

2
TAB: 7559
EN
The instructions manual can be downloaded from the website www.vimar.com
Installation rules
Installation must be carried out by qualied persons in compliance with the current regulations regarding the installation of
electrical equipment in the country where the products are installed.
Regulatory compliance
EMC directive
Standards EN 60065, EN 61000-6-1, EN 61000-6-3 and
EN 60118-4. .
WEEE - User information
The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be
collected separately from other waste. The user must therefore hand the equipment at the end of its life cycle over to
the appropriate municipal centres for the di󰀨erentiated collection of electrical and electronic waste. As an alternative
to independent management, you can deliver the equipment you want to dispose of free of charge to the distributor when
purchasing a new appliance of an equivalent type. You can also deliver electronic products to be disposed of that are smaller
than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area of at least 400 m
2
. Proper
sorted waste collection for subsequent recycling, processing and environmentally conscious disposal of the old equipment
helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing
and/or recycling materials used in manufacture.
This product was developed using FreeRTOS
TM
software - http://www.freertos.org/

3
TAB: 7559
EN
Description
Wall-mount Tab series hands-free video entryphone for Due Fili Plus system with 4.3" LCD colour display, loudspeaker for calls,
capacitive keypad for entryphone functions (unlocking, self-starting, auxiliary services, volume, brightness and contrast controls)
and intercom calls.
Desktop installation is possible with the desktop base accessory 753A (sold separately).
Can be used by hearing aid wearers.
Technical characteristics
• Wall-mounted, with metal bracket, in box: circular 2M (Vimar V71701), 3M (Vimar V71303, V71703) horizontal/vertical and
square British standard.
• LCD 4.3” 16:9 display, resolution 480x272 pixels
• Minimum video signal level on the bus for reception: -20 dBm
• Capacitive touch keypad with backlit symbols.
• Powered from BUS terminals 1, 2 - nominal voltage 28Vdc
• Power consumption:
- in standby: 17 mA
- maximum current: 280 mA
• Ambient class: Class A1 (indoor use)
• IP30 protection rating
• Operating temperature: -5°C to +40°C (indoor use)
• Electronic ringtone with 10 different melodies.
• Input for landing call.
• Dimensions: 155 x 145 x 23.5 mm
• DIP switch for line termination impedance.
Audio frequency function for hearing aids (Teleloop)
The video entryphone can be used by people wearing hearing aids.
For correct functioning of the hearing aid, please refer to its instruction manual. Any metal objects or electronic equipment in the
vicinity may a󰀨ect the quality of the sound received by the hearing aid.
Maintenance
Clean using a soft cloth. Do not pour water onto the appliance and do not use any type of chemical product.
Cleaning must be carried out either with the apparatus powered o󰀨 (= disconnected from the bus) or after activating the keypad
cleaning procedure (see the relative paragraph in the user manual).
Warnings for the user
Do not open or tamper with the appliance.
In the event of faults, contact specialized personnel.

4
TAB: 7559
EN
Installation
Important: The device should be installed at a height of approximately 160 cm off the floor, taking care not to expose it to direct
sources of light so as to avoid annoying glare on the surface of the LCD screen.
Note: Fig. 1 shows the recommended installation distances, unless otherwise specified by current regulations.
1. Secure the plate to the wall, with metal bracket, in box: circular 2M (Vimar V71701), 3M (Vimar V71303, V71703) horizontal/
vertical and square British standard.
2. Wire the terminal block (Fig. 5).
3. Terminate the video signal (Fig. 6)
4. Install the video entryphone as follows: position the video entryphone on the plate keeping it slightly raised. While keeping the
front panel pressed, apply a light downward pressure until it clicks into place.
5. Should you need to remove the monitor you need to apply a light pressure on the lever (Fig. 3) and lift it (upwards) to release
the video entryphone from the frame.
Fig. 1
1,20m1,60 / 1,65m
> 10 cm

5
TAB: 7559
EN
Fig. 2
Fig. 3

6
TAB: 7559
EN
Connections
On the rear there is a terminal board for:
• connection of the Due Fili Plus bus
• The local Landing Call input. The maximum connection distance is 10 m. When suitably programmed using SaveProg,
this input can be used for the Alert function. See the relative paragraph.
Connection terminal block
Terminals Function
1, 2 DUE FILI PLUS digital bus.
FP Landing Call button input (terminal M reference).
MReference earth
Note: Art. 7559 does not have terminals for an additional power supply. For this reason, if the section of the Due Fili bus
in which the internal unit is located is busy with another call/conversation, or another 7559 or 40505 is switched on for any
reason, regardless of its operating status, it will not be possible to switch on a second 7559 or 40505 and a tone will sound
to warn the user. The only possible action is to operate the lock, stair light or auxiliary function using the dedicated buttons,
provided they are not congured for other functions; the Alert function can be used as described in relative paragraph.
Fig. 5

7
TAB: 7559
EN
Video Termination
Select DIP switch to terminate the video signal
A) if the BUS cable enters terminals 1, 2 and continues to another internal unit.
B) when a BUS cable with a characteristic impedance of 100 Ohms (Elvox 732I or 732H cable) enters terminals 1, 2 and the
riser stops in the internal unit
C) when a BUS cable with characteristic impedance of 50 Ohms (Cat. 5 or Cat. 6 twisted pair cable) enters terminals 1, 2 and
the riser stops in the internal unit.
Fig. 6

8
TAB: 7559
EN
Connection
Connecting the internal unit in the in/out configuration
Cable riser
In/out wiring diagram
Wiring diagram with cable terminating in the internal unit
Variant for connecting the landing or alert button
Connecting the FP/M terminal
2
1
FP
M
2
1
FP
M
K
C
50Ω
B
100Ω
A
OPEN
ON
12
ON
12
ON
12
C
50Ω
B
100
Ω
A
OPEN
ON
12
ON
12
ON
12
Termination to apply
Termination to be applied depending
on the characteristic impedance of
the cable
2
1
FP
M
Cable riser
Connecting the internal unit in terminal conguration

9
TAB: 7559
EN
Key functions
In the subsequent sections of this document the touch keys are designated as shown in the gure below:
C(Access Menu
conguration)
P/A (Answer / End call /
Call to switchboard)
T4 (Stair light / Actuator
menu)
Lock
T2 (AUX2 / Intercom
menu)
T1 (Self-start)
T3 (Ringtone mute / Mute
microphone)
At rest, none of the buttons perform the touch function, but must be pressed for longer (around 0.4 s): this prevents the
accidental activation of commands. Unless specically disabled, the recognition notice is given by acoustic signalling.
Keys T1..T4 have two operating contexts:
• Actuations
• Intercom
In the Actuations context, keys T1..T4 have a default (when not programmed), as indicated in the following gure, along
with the default icons: They can be programmed from the installer menu or using SaveProg.
KEY ICON MEANING
T1 Self-start
T2 Aux 2
T3 F2 last outdoor unit
T4 Aux 1
In the Intercom context keys T1..T4 have no default conguration. They can be programmed from the installer menu
or using SaveProg.
T2 (P7 for SaveProg) is not congured by default and controls the second relay (Aux2). If it is congure via SaveProg,
it runs the programmed function. In standby, if only one of the Intercom context programmings are run, whatever the
programming of T2, 7559 will directly run the programmed intercom call. If two or more Intercom context programmings
are run, then the Intercom context menu is shown so that the user can decide which call to make.
The following table summarises and claries the T2 operation. It refers to the SaveProg programming, as this does not
depend on the context.

10
TAB: 7559
EN
CONFIGURATION STANDBY CALL / CONVERSATION / SELF-
START / ACTUATIONS CONTEXT
None of P3..P6 congured. P7
not congured. Aux2
None of P3..P6 congured. P7
congured. Programmed function in P7
Only one of P3..P6 (Pn)
congured, the others not. P7 not
congured.
Intercom call or alert
programmed in Pn Aux2
Only one of P3..P6 (Pn)
congured, the others not. P7
congured.
Intercom call or alert
programmed in Pn Programmed function in P7
At least two of P3..P6 congured.
P7 not congured.
The Intercom context is
shown Aux2
At least two of P3..P6 congured.
P7 congured.
The Intercom context is
shown Programmed function in P7
T3 has the function of ringtone mute / mute microphone. The associated LED will operate also as an indicator for:
• User absent (the internal unit rejects the call from an outdoor unit and consequently the call is unsuccessful). In
this case the LED ashes at intervals of 0.1 s on and 0.9 s o󰀨.
• Ringtone disabled (the internal unit does not ring for calls from the outdoor unit, but otherwise functions normally).
In this case the LED is on steady.
The LED is essential when the display is switched o󰀨.
The C key cannot be programmed and its function is context-dependent.
The P/A key is used to answer or close a call / conversation. In standby it calls the porter switchboard, if the
management with switchboard is active. Moreover, the LED associated to the P/A key remains on and switches
o󰀨 briey for 1, 2, 3 or 4 times for each cycle according to the number of calls received and but not answered for any
reason. If there are any missed calls, press the P/A key for 2 s to reset the call counter. The same can be done by
re-activating the ringtone, after self-start, or after answering a call.
By default, the LOCK key controls the lock of the last outdoor unit to make a call or the outdoor unit for which self-
start procedure was performed. It can only be programmed using SaveProg. The LED associated with the LOCK
key indicates door open status of the system, essential when the display is switched of, even if the same key is pro-
grammed for another function. In some states (e.g. conversation) the icon also appears in the top right-hand side of
the screen.
In standby mode, the screen is completely switched o󰀨. (In the method described above), by activating any one of the
keys T1..T4 and LOCK by default the function is performed without switching on the display unless the function
has to do so in order to be performed, such as self-start.
Starting with 7559 in default, the T4 key enables the rst relay in the Due Fili system. It is usually indicated as stair light
or Aux1. When one or more of the other three keys (T1..T3) in the Actuations context is congured, the T4 key does not
act directly but opens the complete menu of keys T1..T4 in the Actuations context.

11
TAB: 7559
EN
Actuations context
For conguration see the relative paragraph. In the previous gure T1 was re-congured as an icon and was associated
to a function other than default. When pressed, keys T1..T4 run the explicitly set or default function. The icons shown
on T2..T4 are the default settings, unless otherwise selected by the installer. When they are pressed the timeout (15 s)
starts again, and no other controls can be given. The C key forces immediate exit.
The same menu can be recalled during:
• Self-start
• Calls
• Conversation with outdoor unit, another internal unit or the porter switchboard
In these cases, if more than one functions of T1..T3 in the Actuations context has been recongured, the icon corre-
sponding to T4 changes as shown in the following gure:
Re-congured actuations
Press T4 to view the same menu with the internal unit in standby, the di󰀨erence being that key C now leads to the
menu which appeared before pressing T4. Hereafter refer always to the default programming.

12
TAB: 7559
EN
First power up
7559 is supplied without ID. On switching on the display by touching the keypad, the only action possible is to assign
main or secondary internal unit as the ID:
First power up
On choosing one of the two, the internal unit requests ID assignment from the Master outdoor unit and the functions of
the keys change as follows:
Initialisation in progress
T1 now serves to cancel a request, T3 and T4 serve respectively to reduce and increase the speaker volume.
On completion of the ID assignment procedure, the number assigned will appear at the top of the display:
Assigning ID

13
TAB: 7559
EN
After ID assignment
Once the ID has been assigned, the internal unit 7559 has no graphic menu in standby, but only in the call, conversa-
tion, self-start or conguration states.

14
TAB: 7559
EN
User conguration
Press key C to access the user conguration menu. In all the menus, navigation is circular, i.e. scrolling down past the
last option in any menu takes you back to the rst option.
User conguration menu
Each item is selected with T4 .

15
TAB: 7559
EN
Ringtone mute
Use and to enable/disable the ringtone of the internal unit, for calls from outdoor unit, as follows:
ICON IMAGE CONDUCT
Ringtone on
Ringtone mute. The internal
unit does not ring, but
otherwise functions normally.
User away. The internal unit
does not ring and does not
switch on. With conguration
via SaveProg (ag ACK. Grp.
Excl. S) it is possible to ring
secondary internal units,
otherwise the call from the
outdoor unit is rejected and
unsuccessful
Ringtone mute is the same function assigned with T3 to an internal unit in standby or call mode.
The ringtone mute function does not apply to calls received from an internal unit or porter switchboard.
Press T4 to conrm, C to cancel without saving.
Note: in the remaining part of this manual, it is assumed that the functions of T1, T4 and C are understood.
Default: ringtone enabled.

16
TAB: 7559
EN
Select call melody from outdoor unit
Use and to select one of the 10 available melodies (identied by letters A to J) to use as a ringtone for calls from
the outdoor unit. The internal unit plays back the selected ringtone.
Default: melody B.
Select melody for call from outdoor unit
Conrm melody for call from outdoor unit

17
TAB: 7559
EN
Select landing call melody
Use and to select one of the 10 available melodies (identied by letters A to J) to use as a ringtone for calls from
the landing, whether in local contact FP-M or Art. 6120. The internal unit plays back the selected ringtone.
Default: melody C.
Select melody for call from landing
Conrm melody for call from landing

18
TAB: 7559
EN
Select call melody from internal unit or switchboard
Use and to select one of the 10 available melodies (identied by letters A to J) to use as a ringtone for calls from
an internal unit or switchboard. The internal unit plays back the selected ringtone.
Default: melody D.
Select call melody from internal unit or switchboard
Conrm call melody from internal unit or switchboard

19
TAB: 7559
EN
Ringtone volume control
Use and to increase/decrease the ringtone volume, which is indicated by the horizontal bar.
NOTE: the set level is used for all ringtone types (calls from the outdoor unit, landing, indoor unit or switchboard).
Default: level 5.
Select ringtone volume control
Ringtone volume control

20
TAB: 7559
EN
Brightness control
Use and to increase / decrease the brightness of the video signal from an outdoor unit, the level of which is indicated
by the horizontal bar. The internal unit automatically requests the Master outdoor unit to perform a self-start procedure
so that the user can see the e󰀨ect of the brightness control.
NOTE: the level set is used for all outdoor units. Self-start follows the time set in the outdoor unit and is not renewed
with any variations in controls.
Default: level 5.
Select brightness control
Brightness control