VIRTUFIT TR-200i User manual

TR-200i Treadmill
EN
User manual

2
VirtuFit TR-200i Treadmill
EN
INDEX
Safety instructions 3
Assembly instructions 5
Folding instructions 10
Maintenance Treadmill 12
Problem Solutions 14
Operating instruction 16
Programs 20
Android Apps 24
IOS App 28
Exploted Drawing 31
Parts List 32

3
VirtuFit TR-200i Treadmill
EN
SAFETY INSTRUCTIONS
WARNING: Now here we suggest that you should consult with your physician or health
professional before starting your workout, especially for the age up to 35 old or
once-health problem people. We take no responsible for any problems or injuries
if you don’t following our specication. Treadmill will be carefully assembled and
covered the motor shield, then connect to the power.
– Ensuring the safety clamps were attached to the clothing or belts before using the treadmill.
– Please do not insert any items to any part of the equipments, which would damage the equipment.
– Position the treadmill on a clear, level surface. Do not place the treadmill on thick carpet as it may
interfere with proper ventilation. Do not place the treadmill near water or outdoors.
– Never start the treadmill while you are standing on the walking belt. After turning the power on and
adjusting the speed control, there may be a pause before the walking belt begins to move, always
stand on the foot rails on the sides of the frame until the belt is moving.
– Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose tting clothing
that may be caught in the treadmill. Always wear running or aerobic shoes with rubber soles.
– Keep the children and pets away from the treadmill while starting workout.
– Don’t exercise in 40 minutes after dinner.
– The equipment is suitable for adults, children need be accompanied with adults while workout.
– You must hold on to the handrails until you become comfortable and familiar with the treadmill
when it is your rst workout.
– Treadmill is indoor-using equipment, not outdoor-using for avoiding damage. Keep the store-place
clean and at, drying. Prohibiting the other purpose using, only for workout.
– Please purchase the power-line to the distributor or contact with our company directly, for the
powerline only equip to the treadmill.
ATTENTION

4
VirtuFit TR-200i Treadmill
EN
SAFETY INSTRUCTIONS
– The treadmill is for indoor and not outdoor use to prevent damage on the product. Keep the storage
area dry, clean and at. It is forbidden to use the device for other purposes than before training.
– Only use the power cable supplied by the supplier for the treadmill. If the cable is missing, please
contact our company.
– If the treadmill should suddenly increase in speed due to an electronics failure or the speed being
inadvertently increased, the treadmill will come to a sudden stop when the pull pin is disengaged
from the console.
– Do not connect line to the middle of cable; do not lengthen cable or change the cable plug; do not
put any heavy thing on cable or put the cable near the heat source; forbid using socket with several
holes, these may cause re or people may be hurt by the power.
– Cut o the power when the equipment is not used. When the power is cut o , do not pull the
power line to keep the wire unbroken. Insert the plug to the socket with the safety ground circuit,
for the power-line is professional equipment .You must contact with the professional people directly
while the line is damaged.
– This Treadmill only for home-using, the max user weight is 140 KGS.
– Please keep the space at least 1 X 2 meter at the end of base frame to escape any accidents!

5
VirtuFit TR-200i Treadmill
EN
ASSEMBLY INSTRUCTIONS
Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and
the treadmill. Some parts (bolts, screws, etc.) are already attached to / in the treadmill.
Socket screws: The treadmill contains socket screws, make sure that the allen key is rmly in the bolt
before you apply force to the key. In this way you prevent the head of the socket head screw from being
rotated.
– Let the Upright cable thought the right upright.
– Use the bolts and washer x the left and right upright.
STEP 1

6
VirtuFit TR-200i Treadmill
EN
– Fix the strengthen tube to the uprights with bolts and washers.
STEP 2
ASSEMBLY INSTRUCTIONS

7
VirtuFit TR-200i Treadmill
EN
– Connect the console cable and upright cable.
– Assembly the console with bolts and washers.
STEP 3
ASSEMBLY INSTRUCTIONS

8
VirtuFit TR-200i Treadmill
EN
– Fix the side covers with screws.
STEP 4
ASSEMBLY INSTRUCTIONS

9
VirtuFit TR-200i Treadmill
EN
– Put on the power cord and safety key, then power on the machine.
Self-Checking: When using for the rst time, it is necessary to make the machine carry on
–Remove the safety key, press MODE and hold, then insert the safety key again, the machine enters
into self-checking state. During this state, pressing START/STOP two times , the machine begins to
self –check. It stops automatically after self-checking.
Note: Don’t stand on the machine when self-checking.
STEP 5
ASSEMBLY INSTRUCTIONS

10
VirtuFit TR-200i Treadmill
EN
FOLDING INSTRUCTION
PUSH UP
UNFOLDING
Hold the running deck which showed in“F”
position and then fold it up with the arrow
direction until you hear a “bang”voice from the air
cylinder.
Attention: it is forbidden to fold up when the
machine is in running or incline mode.
Support place F with hand , kick the place E of air
pressure bar, then the base frame will fall down
automatically.

11
VirtuFit TR-200i Treadmill
EN
FOLDING INSTRUCTION
To transport, hold the treadmill from position “F”
and tilt until the wheels are able to move on the
ground.
To tilt, start by placing one hand at position“F” to
support the top end of the treadmill. Next, place
one foot at position“D” to hold the bottom end of
the treadmill steady. With your foot at “D”, slowly
tilt the top of the treadmill downward towards
the ground. Once the Main Frame“F” reaches a
low enough point, the wheels of the treadmill will
become active.

12
VirtuFit TR-200i Treadmill
EN
MAINTENANCE TREADMILL
RUNNING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low maintenance deck system. The belt/ deck friction
may play a major role in the function and life of your treadmill, thus requiring periodic lubrication. We
recommend a periodic inspection of the deck. You need contact with our service center if you nd the
damage of the deck.
We recommend lubrication of the deck according to the following timetable:
I. Light user (less than 3 hours/ week) annually
II. Medium user (3-5 hours/ week) every six months
III. Heavy user (more than 5 hours/ week) every three months
Best indicator is to lubricale when the walking platform feels dry. We recommend that you buy the
lubrication from our distributor or directly to our company.
Attention: Any repair need the professional technician.
I. We suggest that you should cut o the power
for 10 minutes after keep running 2HS ,so that it’s
good for maintain the treadmill.
II. For avoiding the slipping during running , the
belt not too loose; for avoiding the more abrasion
between the roller and belt and maintain the
machine’s good running ,the belt not too tight.
You can adjust the distance between plates and
belt, the belt be away from the plates about 50-
75mm on both sides, if the best not too tight and
loose.
We strongly recommend that you do the following:
1. Switch o and remove the power cable from the wall after every use, especially if children are present.
2. Clean your treadmill after use.
3. Use a dry cloth to clean the control panel and areas around the power switch. Use a soft clean cloth
and cleanser to remove stubborn stains and dirt o the running belt.
4. Tighten the running belt once a month.
5. Keep your treadmill in a safe dry place away from heat and water.
LUBRICATING THE BELT

13
VirtuFit TR-200i Treadmill
EN
MAINTENANCE TREADMILL
(1) Running belt deviates to left - Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see g. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
(2) Running belt deviate to right - Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see g. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
(3) Running belt jam - If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see g 3).
RUNNING BELT ADJUSTMENT

14
VirtuFit TR-200i Treadmill
EN
LOOPBAND AFSTELLEN
PROBLEM SOLUTIONS
This treadmill is designed in a way that in the event of an electrical fault, the machine will turn o
automatically to prevent any injuries to the user and to prevent damage to the machine (i.e. motor).
When the treadmill behaves erratically, simply reset the treadmill by turning the power switch o, waiting
for 1 minute then turning the power button back on.
If, after you have reset the treadmill, it is still not running correctly, please run the self-checking analyse
(please refer to Self-Checking) to distinguish what type of error problem the machine is encountering.
Before attempting any work on the treadmill, ensure that the power is o and the plug is removed
from the power point. Do not use extension leads as it may lead to power decrease and failure.
ERROR CODE PROBLEM DESCRIPTION CORRECTIONS
E02 Over voltage protection of motor 1. Make the machine self-checking again
2. Change the controller
E03 Over current protection
1. Clean the dust between running board and
belt, then put some oil
2. If the running belt wear seriously, please
change running belt
E04 The motor open circuit
1.Check the connect wire of motor, if the
connect wire loose, pls connect it again
2.The motor carbon brush wear, replace the
carbon brush or motor
3.Change the controller
E05 EEPROM damage or access
problems Change the controller
E06 Communication error
Check the connect wire between incline motor
and control board, if it loose or broken, pls
change the wire
E07 Incline error when selfchecking
1.Check the connect wire between incline
motor and control board, if it loose or broken,
pls change the wire
2.Change the incline motor
E08 Speed error when selfchecking
1.Check the distance from speed sensor to the
magnetic of roller, and ajust it with 3mm
2.Change the speed sensor
E09 Short-Circuit problem Change the control board

15
VirtuFit TR-200i Treadmill
EN
LOOPBAND AFSTELLEN
PROBLEM SOLUTIONS
ERROR CODE PROBLEM DESCRIPTION CORRECTIONS
“-” Safety key not connected Insert safety key
ER
When treadmill at running state,
the incline window display“Er”, it
is incline VR error
1. Check the connect wire between incline
motor and control board, if it get loose or
broken, pls connect it again or change it
2. Change the incline motor
No Power
1. Check fuses (They are located on the controller under the motor cover).
2. Check power outlet (Plug something else into the power outlet to ensure that the power outlet is
working correctly).
3. Check Power Cable (You may need to take it to an electrician).
4. Ensure that the safety key is installed, as the treadmill will not power on without it.
If you can not solve the problem, please contact your dealer.

16
VirtuFit TR-200i Treadmill
EN
LOOPBAND AFSTELLEN
OPERATING INSTRUCTION
KEY DESCRIPTION
MODE Power on the machine, press it to choose pre-set programs P1-P36. Press CLEAR/
SET to exist.
START / STOP Power on the machine, press it to start running. When running,press it to stop
and record the running. Press CLEAR/SET to clear up the record.
CLEAR / SET Power on the machine, press it to choose time,distance,calorie count-down
training. When running, clear up time,distance and calorie.
(4) SPEED + When running, press it to increase speed by 0.5km/h. Hold on it, speed is
increased continuously.
KEYS FOR CONSOLE

17
VirtuFit TR-200i Treadmill
EN
KEY DESCRIPTION
(5) SPEED - When running, press it to decrease speed by 0.5km/h.Hold on it, speed is
deceased continuously.
(6) QUICK SPEED Speed 3,6,9, when running, press it to choose speed.
(7) INCLINE + When running, press it to increase incline by 1 level. Hold on it, incline is
increased continuously.
(8) INCLINE - When running, press it to decrease incline by 1 level. Hold on it, incline is
decreased continuously.
(9) QUICK INCLINE Incline 3,6,9, when running, press it to choose incline.
(10) INCLINE +
in the handrail
When running, press it to increase incline by 1 level. Hold on it, incline is
increased continuously.
(11) INCLINE -
in the handrail
When running, press it to decrease incline by 1 level. Hold on it, incline is
decreased continuously.
(12) SPEED +
in the handrail
When running, press it to increase speed by 0.5km/h. Hold on it, speed is
increased continuously.
(13) SPEED -
in the handrail
When running, press it to decrease speed by 0.5km/h.Hold on it, speed is
deceased continuously.
OPERATING INSTRUCTION

18
VirtuFit TR-200i Treadmill
EN
LOOPBAND AFSTELLEN
OPERATING INSTRUCTION
USER’S MODE OPERATION
Count-down training: Power on the machine, press CLEAR/SET to enter TIME count-down training,
press it again to enter DISTANCE count-down training, press it once more to enter CALORIE countdown
training. Finally press CLEAR/SET to exit.
TIME count-down training: power on the machine, press CLEAR/SET, TIME gure glitering, showing
30:00. Press SPEED+,- to choose the time between 5-99minutes. Press START/STOP to start at speed of
1.0km/h. Speed can be adjusted by pressing SPEED+,-. The machine stops when time shows 00:00.
DISTANCE count-down traing: power on the machine, press CLEAR/SET two times, distance gure
glitering, showing 1.0km. Press SPEED+,- to choose the distance between 1.0-9.0km. Press
START/STOP to start at speed of 1.0km/h.Speed can be adjusted by pressing SPEED+,-. The machine
stops when distance shows 0.00.
CALORIE count-down training: Power on the machine, press CLEAR/SET three times, calorie gure
glitering, showing 50CAL. Press SPEED+,- to choose the calorie between 10-990CAL. Press
START/STOP to start at speed of 1.0km/h.Speed can be adjusted by pressing SPEED+,-. The machine
stops when calorie shows 0.
Quick-Start Operation
Press and release the START/STOP to begin belt movement, at 1.0 Km/h, then adjust to the desired
speed using the ‘+’ or ‘-’. You may also use the quick speed keys (3, 6 and 9) to adjust the speed. You
can also use ‘speed +’or ‘speed -’to adjust the speed on handrail.
To slow the treadmill down, press and hold the ‘speed -’ key to desired speed. You may also press the
rapid speed adjust keys: 3, 6, 9.
– In a state of running, single press START/STOP, the walking belt will gradually slow down.
– In the state of running, single press CLEAR/SET will reset time, distance, calorie.
Incline Feature
– Incline may be adjusted anytime after belt movement.
– Incline can’t be back to 0 after removing safety key.
– Incline can be back to 0 after starting machine again.

19
VirtuFit TR-200i Treadmill
EN
Pulse Grip Feature
Hold on both stainless steel pulse sensors in the handrails, the The Pulse (Heart Rate) console window will
display your current heart rate during the workout within 15 seconds . Note: You must use both stainless
steel sensors to display your pulse.
Calorie Display
Displays the cumulative calories burned at any given time during your workout.
– Note: This is only a rough guide used for comparison of dierent exercise sessions, which cannot
be used for medical purposes.
OPERATING INSTRUCTION

20
VirtuFit TR-200i Treadmill
EN
PROGRAMS
This treadmill oers 36 present programs (P1-P36). The rst 24 preset programs (P1 to P24) are only for
speed; the another 12 preset programs (P25 to P36) are a combination on speed and incline.
Each preset program has a maximum speed level that is displayed when a desired workout is chosen. The
speed that the particular program will achieve will be displayed in the Speed window. Each program has
various speed changes throughout.
To Select a Program:
Make sure the machine is in the stop position, single press‘clear’ to enter into resetting state. Press ‘MODE’
to choose desired program (P1,P2, …..P36), then press and release‘START/STOP’ to begin the program with
default values.
The speed window will now be showing the preset speed of the selected program.
Each program will continue 10 minutes. After every one minute program and speed can be altered manually
or automatically. 3 Seconds before the ending of program a buzzer will sound three times, then the running
belt will come to a stop.
0
2
4
6
8
10
123456789 10
km/h
minute
Program 1
speed
0
2
4
6
8
10
12345678 91 0
km/h
minute
Program 2
speed
0
2
4
6
8
10
12
14
12345678 91 0
km/h
minute
Program 3
speed
0
5
10
15
12345678 91 0
km/h
minute
Program 4
speed
0
2
4
6
8
10
12
14
123456789 10
km/h
minute
Program 5
speed
0
2
4
6
8
10
12
14
123456789 10
km/h
minute
Program 6
speed