VIRTUFIT TR-200i User manual

TR-200i
VFLOTR200i
USER MANUAL
SERIAL NUMBER
SERIENNUMMER
SERIENUMMER
NUMERO DE SERIE
HOW TO
RECYCLE
@virtufit_fitness
VirtuFit
www.virtufit.com
ASSEMBLY
VIDEO

USER MANUAL
02
TOOLKIT
NOTE! Do not connect the unit to the power supply until it is fully assembled.
LET OP! Sluit het toestel pas aan op het stroom wanneer het volledig is gemonteerd.
HINWEIS! Schließen Sie das Gerät erst dann an das Stromnetz an, wenn es vollständig montiert ist.
REMARQUE! Ne connectez pas l’appareil à l’alimentation électrique avant qu’il ne soit entièrement assemblé.
USER MANUAL
M8 Locknut * 4
Spanner * 1
6mm Hex Key * 1
5mm Hex Key * 1
S
Ø8 Plate Washer * 4
M8*50 Bolt * 4
M8*55 Bolt * 2
M8*12 Bolt * 4 M8*16 Bolt * 4
ST4.2*13 Hood Screw * 8

USER MANUAL
03
61
64
75
49 60
48
6
63
75
48
STEP 01
STEP 02
CAUTION! Only hand-tighten part 6 after assembly.
LET OP! Draai onderdeel 6 alleen handvast, na
de montage van het scherm het onderdeel goed
vastdraaien.
ACHTUNG! Teil 6 nach der Montage nur handfest
anziehen.
ATTENTION! Ne serrer la pièce 6 qu'à la main après
l'assemblage.

USER MANUAL
04
STEP 03
STEP 04
61
64 48
62
76
55
55

USER MANUAL
05
STEP 05
STEP 06
43
39

USER MANUAL
06
USER MANUAL
FIG. A

USER MANUAL
07
FIG. B - PROGRAMS
USER MANUAL
6 6 12 9 9 10 10 10
P36, speed( km/ h) , i ncl i ne( l evel s)
8 9 10 11 9 6 8 9
8 9 10 10 10 10 10 10
0
2
4
6
8
10
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 1
speed
0
2
4
6
8
10
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 2
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 3
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 4
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 5
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 6
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 7
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 8
speed

USER MANUAL
08
FIG. B - PROGRAMS
USER MANUAL
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 9
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 10
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 11
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 12
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 13
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 14
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 15
speed
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 16
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 17
speed
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 18
speed

USER MANUAL
09
FIG. B - PROGRAMS
USER MANUAL
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 19
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 20
speed
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 21
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 23
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 22
speed
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h
minute
Program 24
speed
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 25
speed
incline
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h, levels
minute
Program 26
speed
incline
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h, levels
minute
Program 27
speed
incline
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h, levels
minute
Program 28
speed
incline

USER MANUAL
10
FIG. B - PROGRAMS
USER MANUAL
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 29
speed
incline
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 30
speed
incline
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 31
speed
incline
0
5
10
15
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 32
speed
incline
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
k/h,levels
minute
Program 33
speed
incline
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h, levels
minute
Program 34
speed
incline
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10
km/h,levels
minute
Program 35
speed
incline
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10
km/h,levles
minute
Program 36
speed
incline

USER MANUAL
11
USER MANUAL
FIG. C
1
4 5
2 3

ENGLISH
EN
12
INDEX
Safety instructions 13
Guarantee 13
Assembly instructions 13
Adjusting 14
Folding instructions 14
Moving instructions 14
Training with heart rate 14
Training with fitness applications 15
Maintenance 15
Lubricating 16
Troubleshooting 16
Console 16
Programs 17
Training guidelines 18
SAFETY INSTRUCTIONS
WARNING!
Consult your doctor before you start exercising. This is particularly
important for people with health problems. Please read all
instructions before using the machine. VirtuFit assumes no
responsibility for injury or property damage resulting from the
use of this equipment. Please read this manual carefully before
assembling and/or using the machine.
• Make sure that the machine is properly assembled and that all
nuts and bolts are tight before using it.
• Do not wear loose clothing to avoid getting caught in moving
parts.
• Always wear clean sports shoes when using the appliance.
• Keep children and pets away from the appliance when in use.
• Maintain your balance when using the device.
• Do not place your fingers or other objects in the moving parts.
• Before exercising, consult your physician to determine the
appropriate frequency, duration and intensity of exercise for
your age and physical condition. Stop exercising immediately
if you experience nausea, shortness of breath, fainting, headache,
chest pain, tightness or any other discomfort.
• This machine should only be used by one person at a time.
• This machine is designed for domestic use and the maximum
user weight is 140 kg.
• Leave 1-2 metres of space behind the machine to avoid accidents.
• Place the machine on a clean, flat surface. Do not place it on a
thick carpet, as this may hinder the ventilation of the machine.
Do not place the machine outdoors or near water.
• Keep the storage area dry, clean and level to prevent damage.
Do not use the device for any purpose other than training.
• Use the appliance only in an insulated room with an ambient
temperature between 10 °C and 35 °C. Only store the appliance
only in an insulated room with an ambient ambient temperature
between 5 °C and 45 °C.
GUARANTEE
Warranty claims are excluded if the cause of the defect is the result
of:
• Maintenance and repair work not carried out by an official
dealer. Provided otherwise specified by the supplier
• Improper use, negligence and/or poor maintenance.
• Failure to maintain the appliance in accordance with the
manufacturer’s instructions.

Missing parts: If any parts are missing from the packaging, carefully
check the polystyrene foam and the appliance itself. Some parts (bolts,
screws, etc.) are already attached to the unit.
Error message: Make sure that all cables are carefully attached. The
aluminium feet of the console are very sensitive and must be kept
straight. If the console gives an error message after the machine
has been mounted, the aluminium feet of the console may be bent.
Straightening the aluminium feet may make the error message
disappear.
Hex head bolts: Make sure that the hex head spanner is pushed into
the bolt before applying force. This will prevent the head of the socket
bolt from turning.

ENGLISH
EN
13
Unfolding (2)
• Support the treadmill with your hands at point F.
• Press down on point E with your foot and the treadmill will
unfold. Do not push the treadmill down, it will lower
automatically.
• Hold the belt and guide it until it touches the floor.
• The treadmill is unfolded.
MOVING INSTRUCTIONS
NOTE! Keep the appliance in a dry room and out of reach of
children. Ensure that the appliance is stable and secure so that it
cannot fall on children or animals.
1
F
F
D
A B
• Support the treadmill with your hands at point F and your foot
at point D.
• Using your hands (F), slowly push the treadmill towards the
ground. When the lowest point of position F is reached, the
wheels can be used.
• Push the treadmill to where it is to be placed.
TRAINING WITH HEART RATE
Hand sensors
This VirtuFit fitness machine is equipped with hand sensors for
measuring heart rate. The hand sensors are attached to the handle
and only work if both sensors are held for a longer period of time. For
optimal performance, it is important that the hands are slightly moist
and exert constant pressure on the sensors. Hands that are too dry or
moist may cause abnormal readings.
NOTE! To avoid interference, never use the hand sensors with a
wireless heart rate monitor.
ADJUSTING
Adjusting
1. The treadmill veers to the left: Turn on the treadmill, set the
speed to 2 to 3 km/h without forcing. Use the Allen key to turn
the screw on the left side of the end of the treadmill a quarter
turn to the right (1). Run the treadmill for 1 to 2 minutes without a
load. Repeat the process until the treadmill is exactly in the
middle.
2. The treadmill turns to the right: start the treadmill, set the
speed to 2 to 3 km/h without a load on the treadmill. Using the
hexagonal key, turn the screw on the right side of the end of the
treadmill a quarter turn to the right (2). Run the treadmill for 1 to
2 minutes without a load.
3. The treadmill has jammed: Use the Allen spanner to turn the
screw on the right side of the end half a turn to the right and
the screw on the left side of the end half a turn to the right as
well. Repeat the process until the blockage is resolved (3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
FOLDING AND UNFOLDING INSTRUCTIONS
NOTE! Keep the appliance in a dry room and out of reach of
children. Ensure that the appliance is stable and secure so that it
cannot fall on children or animals.
1
F
E
2
F
Folding (1)
• Support the treadmill with your hands at point F.
• Push the treadmill upwards until you hear a click on the spring.
• The treadmill is folded.
CAUTION! Do not fold the treadmill while it is in use.

ENGLISH
EN
14
Fitshow
APP STORE GOOGLE PLAY MANUAL
MAINTENANCE
Safe and efficient use can only be achieved if the appliance is
properly installed and maintained. It is your responsibility to ensure
that the appliance is maintained regularly. Parts that have been
used and/or damaged must be replaced before the appliance is
used again. The appliance should only be used and stored indoors.
Long-term exposure to weather and temperature/humidity changes
can have a serious impact on the electrical components and moving
parts of the unit. Always unplug the power cord from the unit before
cleaning or servicing it.
Daily maintenance
• Clean and remove sweat and moisture after each use.
• Check that the unit is free of dust and dirt.
• Do not use aggressive cleaning agents and keep the device
away from moisture.
Semi-annual maintenance
• Inspect all nuts and bolts on the moving parts of the machine.
Tighten bolts and nuts as necessary and appropriate.
• Remove dust from the treadmill. Switch off the treadmill and
remove the power supply. Carefully remove the cover and wipe
off any dust and dirt with a soft cloth or use a (hand) hoover if
necessary. Replace the cover and turn the power back on.
We recommend the following:
• Clean the unit after use.
• Use a dry cloth to clean the control panel and the areas around
the on/off switch.
• Use a soft, clean cloth and detergent to remove stubborn marks
and dirt from the unit.
• Store the unit in a safe, dry place away from heat and water.
Wireless heart rate receiver (5 kHz)
This VirtuFit fitness device is equipped with a wireless heart rate
receiver. For the heart rate measurement with a wireless heart
rate monitor, you use a heart rate monitor which works on a 5 kHz
frequency. With a wireless heart rate monitor, it is important that the
electrodes are slightly moist and the heart rate monitor fits well to
your body. Refer to your heart rate monitor's user manual for proper
instructions. Incorrect use of the heart rate monitor may result in
abnormal readings.
NOTE!
• A wireless heart rate monitor is not included as standard.
Contact your dealer to purchase a wireless heart rate monitor.
• To avoid interference, never use the wireless heart rate
monitor in combination with the hand sensors.
WARNING!
• If you have a pacemaker, we recommend that you consult
your physician before using a wireless heart rate monitor
• In rooms with multiple heart rate monitors, it is recommended
that you keep enough distance to avoid interference between
different devices.
• Always try to keep the wireless heart rate monitor within a
range of 1 meter from the console for optimal reception.
• Always wear a wireless heart rate monitor directly on the
body, under clothing.
TRAINING WITH FITNESS APPLICATIONS
VirtuFit does not provide service for third party fitness applications
such as Kinomap, iConsole, FitShow etc. If you encounter problems
with a third party fitness application, please contact the developer
of the application in question.
Instruction
• To scan the QR code with an Android or IOS phone or tablet, a
QR code scanner is required. The app for scanning QR codes can
be downloaded from the App Store or Google Play Store.
• Scan one of the QR codes below to go directly to the App Store or
Google Play Store page where the fitness app can be
downloaded.
• Scan the QR code on the right to access the fitness app
manual. The manual describes step by step how to connect the
fitness app to the device, how the fitness app works and what its
capabilities are.

ENGLISH
EN
15
Totally Foldable TR-50i Loopband
Gebruiksaanwijzing
NL
T+31 (0)74-7600219
Eser
W
Voor vragen of ontbrekende onderdelen kunt u contact opnemen met Fitness Benelux:
CAUTION! Regular maintenance will prolong the durability of the
treadmill and prevent injury!
TROUBLESHOOTING
There is no signal when the power supply is connected
Check that the cables to the console are connected correctly. Make
sure that all cables are securely fastened. The aluminium ends of the
console cables are very sensitive and should be kept straight. If the
console issues an error message, the aluminium ends of the cable may
be tilted. Straighten the aluminium ends, which may resolve the error
message.
No power: Check that the power cable and cables are properly
connected.
Loss of power: Check that the sensor cable is correctly connected.
CONSOLE
3 6 9 3 6 9
INCLINE SPEED
MODE
To choose the preset programmes, press to
restore the selection.
START/
STOP
To start a workout, press during use to stop and
view results. To reset the data, press to set the
training target in terms of time, distance and calories.
CAUTION!
• Repairs must be carried out by a professional technician,
unless otherwise specified by the supplier or manufacturer.
• To avoid slipping during exercise, the treadmill belt should
not be too loose. To avoid abrasion between the roller and
the treadmill and to ensure proper operation of the machine,
the treadmill should not be too tight. The distance between
the step and the belt can be adjusted. The distance between
the step and the belt should be 50 to 75 mm on both sides.
Cleaning
General cleaning of the unit will extend its life. Keep the appliance
clean by dusting it regularly. Regular maintenance will prolong the life
of your appliance and prevent injuries! For more information, please
visit https://www.virtufit.nl/service/faq/
CAUTION! Wear clean shoes to reduce the risk of soiling the
machine. At least once a year, remove the cover to remove dust.
LUBRICATING THE TREADMILL
The treadmill is equipped with a pre-lubricated coating that requires
little maintenance. Wear and tear of the treadmill plays an important
role in the function and durability of the treadmill and should therefore
be lubricated periodically. We recommend that you check the treadmill
regularly.
Recommended lubrication of the treadmill
• Low usage (less than 3 hours per week): once a year.
• Medium use (3 to 5 hours per week): every six months.
• Heavy use (more than 5 hours per week): every three months.
Instruction
• Lift the treadmill and clean it with a damp cloth to remove
dirt and dust.
• Apply a small amount of silicone oil under the treadmill. To
do this, use a silicone spray bottle or drip two or three drops of
silicone oil along the length of the belt. Do this on both sides of
the treadmill.
• Turn on the treadmill and let it run for three minutes
without standing on it. This ensures that the silicone oil is
properly distributed on the belt and that excess oil is removed.
• Check the condition of the treadmill regularly and reapply
silicone oil if necessary. Make sure that the belt is clean and dry
before riding on it.

ENGLISH
EN
16
Distance count-down
• Press twice and the display shows 1.0 km.
• Press SPEED to set the distance between 1.0 and 9.0 km.
• Press to start your workout. The treadmill will count down
and stop when 0.00 is displayed in DISTANCE.
NOTE! The workout starts at a speed of 1.0 km/h. The speed can be
adjusted by pressing SPEED .
Calorie count-down
• Press three times and the display will show 50CAL.
• Press SPEED to set the number of calories between 10
and 990 CAL.
• Press to start your workout. The treadmill will count down
and stop when CAL 0 is displayed.
NOTE! The workout starts at a speed of 1.0 km/h. The speed can be
adjusted by pressing SPEED .
Quickstart
Press START / STOP to start the treadmill at 1.0 km/h and set the desired
speed by pressing or . To change speed quickly, press theSPEED
shortcut keys. You can also use the and keys on the
handlebar during your workout.
Incline
The incline can be adjusted at any time during the workout. The incline
cannot be returned to "0%" after removing the safety key. When the
safety key is replaced and the treadmill is restarted, the incline can be
adjusted again.
Pulse grip
Hold the two hand-held sensors in the handles and the display will
show the heart rate measured during the workout within 15 seconds.
NOTE! To measure heart rate, the hand sensors on both handles
must be held firmly. The heart rate measurement is an estimate and
cannot be used for medical purposes.
CLEAR/
SET
Om het doel van de training voor tijd, afstand en
calorie in te stellen.
SPEED
During use, press to increase the speed by 0.5 km/h.
When the button is held down, the speed is increased
continuously.
SPEED
During use, press to reduce the speed by 0.5
km/h. When the button is held down, the speed is
continuously reduced.
QUICK
SPEED
Speeds 3, 6 and 9 km/h. During use, press one of these
buttons to quickly select the speed.
INCLINE
During operation, press to increase the gradient by
one level. When the button is held down, the gradient
increases continuously.
INCLINE
During operation, press to decrease the slope by one
level. When the button is held down, the slope is
continuously reduced.
QUICK
INCLINE
Slope 3%, 6% and 9%. Press one of these buttons during
operation to quickly select the slope.

Count-down
• Press to select the training TIME countdown.
• Press twice to select the training DISTANCE countdown.
• Press three times to select the CALORIE training countdown.
• Press to exit.
Time count-down
• Press and the display will show 30:00.
• Press SPEED to set the time between 5 and 99 minutes
• Press to start the workout. The treadmill will count down
and stop when TIME 00:00 is displayed.
NOTE! The workout starts at a speed of 1.0 km/h. The speed can be
adjusted by pressing SPEED .

ENGLISH
EN
17
The warm-up
The purpose of a warm-up is to prepare the body for training and to
reduce the risk of injury. Warm up your body for two to five minutes
before starting a cardio or strength training session. Do exercises that
increase the heart rate and warm up the working muscles. Examples of
this type of activity are running, jogging, jumping jacks, skipping and
running in place.
Stretching
Stretching while the muscles are warm is very important after a good
warm-up and cool-down. It reduces the risk of injury. Stretching
exercises should be held for 15-30 seconds. Here are some examples of
stretching exercises:
• Toe touch (Fig. C-1)
• Inner thight stretch (Fig. C-2)
• Hamstring stretch (Fig. C-3)
• Achilles stretch (Fig. C-4)
• Side stretch (Fig. B-5)
Cooling down
The purpose of the cool-down is to return the body to its (near) normal
resting position at the end of the workout. A good cool-down slowly
reduces your heart rate and promotes recovery.
Heart Rate Control (HRC)
• Press button until "HRC" appears under the programme.
Select the HRC programme by pressing .
• Select the desired heart rate by pressing under SPEED.
• Press to start the programme.
Speed and incline
During this programme, the speed and angle of incline change
according to your heart rate. The speed and angle of incline increase
as soon as the desired heart rate is not yet reached. If this heart rate is
exceeded, the speed and incline angle will decrease.

This treadmill has 36 preset programs (P1 to P36). The first 24 preset
programs (P1 to P24) relate to speed. The other 12 preset programs (P25
to P36) are a combination of speed and incline (fatburn, hill and fittest).
Each preset program has a maximum speed level which is displayed
when a desired workout is selected. The speed that the program in
question will reach is displayed in the speed window. Each program
has different speed changes.
Selecting a program
• Make sure the treadmill is stationary and press to activate
the reset state.
• Press oto select the required program (P1 to P36) and
press to start the program.
The speed window displays the preset speed of the selected program.
Each program lasts 10 minutes. After each minute, the program and
speed can be adjusted manually or automatically. 3 seconds before
the end of the program, a signal sounds three times, after which the
treadmill stops.
NOTE! All programmes are listed at the beginning of this manual.

A successful training program includes a warm-up, the actual training
and a cool-down. Perform the complete training program at least
twice, but preferably three times a week and keep a rest day between
training sessions. After a few months, the intensity of the training can
be increased, for example to four or five times a week.

NEDERLANDS
NL
18
INHOUD
Veiligheidsinstructies 19
Garantie 19
Montage Instructies 19
    
  
   
Trainen met hartslag 21
Trainen met fitness apps 21
Onderhoud 21
Insmeren van de loopband 22
Probleemoplossingen 23
Foutcodes 23
Console 23
Programma's 23
Trainingsrichtlijnen 24
VEILIGHEIDSINSTRUCTIES
WAARSCHUWING!
Raadpleeg uw arts voordat u begint met trainen. Dit is in het
bijzonder belangrijk voor personen met gezondheidsproblemen.
Lees alle instructies alvorens het toestel gebruikt wordt.
VirtuFit neemt geen verantwoordelijkheid voor geleden letsel
of materiële schade door het gebruik van dit toestel. Lees deze
handleiding zorgvuldig door, voordat u begint met monteren
van het toestel en/of er gebruik van gaat maken.
• Zorg ervoor dat het toestel voor gebruik correct is
gemonteerd en alle bouten en moeren zorgvuldig zijn
vastgedraaid.
• Draag geen loszittende kleding om te voorkomen dat deze in
bewegende delen verstrikt raakt.
• Draag altijd schone sportschoenen bij gebruik van het
toestel.
• Houd kinderen en huisdieren uit de buurt van het toestel,
terwijl deze in gebruik is.
• Zorg dat u evenwicht behoudt tijdens gebruik van het toestel.
• Plaats geen vingers of andere voorwerpen in de bewegende
delen.
• Raadpleeg voorafgaand aan een training uw arts om de
trainingsfrequentie, tijd en intensiteit vast te stellen die
geschikt is voor uw leeftijd en conditie. Stop onmiddellijk
met trainen in geval van misselijkheid, kortademigheid,
flauwvallen, hoofdpijn, pijn, benauwdheid in de borst of
enig ander ongemak.
• Dit toestel dient door slechts één persoon tegelijk te worden
gebruikt.
• Dit toestel is gemaakt voor thuisgebruik en het maximaal
gebruikersgewicht bedraagt 140 kg.
• Houd 1 á 2 meter ruimte vrij achter het toestel om eventuele
ongelukken te voorkomen.
• Plaats het toestel op een schone en vlakke ondergrond.
Plaats het toestel niet op dik tapijt waardoor het ventilatie
kan belemmeren. Plaats het toestel niet buiten of in de
buurt van water.
• Het toestel is voor binnengebruik en niet voor buitengebruik.
Houd de opslagplek droog, schoon en vlak om schade te
voorkomen. Het is verboden om het toestel voor andere
doeleinden te gebruiken dan voor de trainingen.
• Gebruik het toestel alleen in een geisoleerde ruimte met een
omgevingstemperatuur tussen 10 °C en 35 °C. Berg het toestel
alleen op in een geisoleerde ruimte met een
omgevingstemperatuur tussen 5 °C en 45 °C.
GARANTIE
Aanspraak op garantie is uitgesloten indien de oorzaak van het
defect het gevolg is van:
• Onderhoudsmontage en reparatiewerkzaamheden die niet
door een officiële dealer zijn uitgevoerd. Mits anders door de
leverancier aangegeven.
• Bij ondeugdelijk gebruik, verwaarlozing en/of gebrekkig
onderhoud.
• Het niet volgens de fabrieksvoorschriften onderhouden van
het toestel.
MONTAGE INSTRUCTIE
Missende onderdelen: Indien bepaalde onderdelen missen in de
verpakking, controleer dan zorgvuldig het piepschuim en het toestel
zelf. Sommige onderdelen (bouten, schroeven, etc.) zitten al bevestigd

NEDERLANDS
NL
19
waardoor het niet om kan vallen op dieren of kinderen.
1
F
E
2
F
Inklappen (1)
• Ondersteun de loopband met je handen bij punt F.
• Duw de loopband omhoog totdat je een klik hoort van de veer.
• De loopband is ingeklapt.
LET OP! De loopband niet inklappen wanneer deze in gebruik is.
Uitklappen (2)
• Ondersteun de loopband met je handen bij punt F.
• Druk tegen punt E met je voet en de loopband zal uitklappen.
Druk de loopband niet omlaag, deze zal automatisch naar
beneden zakken.
• Houd de band vast en begeleid het totdat het de grond raakt.
• De loopband is uitgeklapt.
VERPLAATSEN
LET OP! Berg het apparaat op in een droge ruimte uit de buurt
van kinderen. Zorg ervoor dat het apparaat stabiel en veilig staat
waardoor het niet om kan vallen op dieren of kinderen.
1
F
F
D
A B
• Ondersteun de loopband met je handen bij punt F en met je
voet bij punt D.
• Duw met je handen (F) de loopband langzaam richting de
grond. Wanneer het laagste punt met positie F is bereikt,
kunnen de wielen worden gebruikt.
• Duw de loopband naar de plek waar deze moet komen te staan.
aan/in het toestel.
Foutmelding: Let er op dat alle kabels voorzichtig worden bevestigd.
De aluminium pootjes van het console zijn zeer gevoelig en deze
dienen recht te blijven. Mocht het console een foutmelding geven na
de montage van het toestel dan kan het zijn dat de aluminium pootjes
van het console schuin staan. Buig de aluminium pootjes weer recht,
dit laat de foutmelding mogelijk verdwijnen.
Inbusbouten: Zorg ervoor dat de inbussleutel goed in de bout zit
voordat er kracht op de sleutel wordt gezet. Op deze manier wordt
voorkomen dat de kop van de inbusbout wordt dolgedraaid.
AFSTELLEN
Band afstellen
1. Loopband wijkt af naar links: Start de loopband, stel de
snelheid in op 2 tot 3 km/u zonder de loopmat te belasten.
Gebruik de inbussleutel om de schroef aan de linkerkant
van het uiteinde een kwartslag naar rechts te draaien (1).
Laat de loopband gedurende 1 tot 2 minuten zonder
belasting draaien. Herhaal het proces totdat de loopmat
precies in het midden zit.
2. Loopband wijkt af naar rechts: Start de loopband, stel de
snelheid in op 2 tot 3 km/u zonder de loopmat te belasten.
Gebruik de inbussleutel om de schroef aan de rechterkant
van het uiteinde een kwartslag naar rechts te draaien (2).
Laat de loopband gedurende 1 tot 2 minuten zonder
belasting draaien. Herhaal het proces totdat de loopmat
precies in het midden zit.
3. Loopband vastgelopen: Gebruik de inbussleutel om de
schroef aan de rechterkant van het uiteinde een halve slag
naar rechts te draaien en de schroef aan de linkerkant van
het uiteinde ook een halve slag naar rechts te draaien.
Herhaal het proces totdat de blokkering is opgelost (3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
EN
Virtufit Totally Foldable TR-50i Treadmill 11
11 NL
INKLAP INSTRUCTIES
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
FOLDING INSTRUCTIONS
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
ensure that they are nog pinced.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
3. Place the machine leaning against the wall or place under a bed.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
RUNNING BELT ADJUSTMENT
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).

LET OP! Berg het apparaat op in een droge ruimte uit de buurt
van kinderen. Zorg ervoor dat het apparaat stabiel en veilig staat

NEDERLANDS
NL
20
TRAINEN MET FITNESS APPS
VirtuFit verleent geen service voor fitness-apps van derde partijen
zoals Kinomap, iConsole, FitShow etc.. Mocht u problemen
ondervinden met een fitness-app van een derde partij, neem dan
contact met de desbetreffende app-ontwikkelaar.
Instructie
• Om de QR-code te scannen met een Android of IOS telefoon
of tablet is een QR-code scanner nodig. De app om QR-
codes te scannen kan in de App Store of Google Play Store
worden gedownload.
• Scan één van de QR-codes hieronder om direct naar de
pagina in de App Store of Google Play Store te gaan waar
de fitnessapp gedownload kan worden.
• Scan de QR-code aan de rechterkant om naar de
handleiding van de fitnessapp te gaan. In de handleiding
staat stap voor stap beschreven hoe de fitnessapp
verbonden dient te worden met het toestel, hoe de
fitnessapp werkt en welke mogelijkheden er zijn.
Fitshow
APP STORE GOOGLE PLAY MANUAL
ONDERHOUD
Veilig en effectief gebruik kan alleen worden bereikt als het
toestel goed wordt gemonteerd en onderhouden. Het is uw
verantwoordelijkheid om ervoor te zorgen dat het toestel
regelmatig wordt onderhouden. Onderdelen die al zijn gebruikt
en/of beschadigd, moeten worden vervangen voordat het toestel
verder gebruikt wordt. Het toestel mag alleen binnen worden
gebruikt en opgeborgen. Langdurige blootstelling aan verwering
en veranderingen in temperatuur/vochtigheid kunnen een ernstige
impact hebben op de elektrische componenten en bewegende
delen van het toestel. Haal altijd de stroomkabel van het toestel
uit het stopcontact voordat het apparaat wordt schoongemaakt of
onderhouden.
TRAINEN MET HARTSLAG
Handsensoren
Dit VirtuFit fitnesstoestel is voorzien van handsensoren voor het meten
van de hartslag. De handsensoren zitten bevestig op het handvat en
werken alleen als beide sensoren voor een langere periode worden
vastgehouden. Voor een optimale werking is het belangrijk dat de
handen licht vochtig zijn en constante druk uitoefenen op de sensoren.
Te droge of vochtige handen kunnen zorgen voor een afwijkende
meting.
LET OP! Gebruik de handsensoren nooit samen met een draadloze
hartslagmeter om storing te voorkomen.
Draadloze hartslagmeter (5 kHz)
Dit VirtuFit fitnesstoestel is voorzien van een draadloze
hartslagontvanger. Voor de hartslagmeting met een draadloze
hartslagmeter gebruikt u een hartslagmeter welke werkt op een 5 kHz
frequentie. Bij een Draadloze hartslagmeter is het belangrijk dat de
elektroden licht vochtig zijn en de hartslagmeter goed aansluit op uw
lichaam. Raadpleeg de gebruikershandleiding van uw hartslagmeter
voor de juiste instructies. Onjuist gebruik van de hartslagmeter kan
zorgen voor een afwijkende meting.
LET OP!
• Een draadloze hartslagmeter wordt niet standaard
meegeleverd. Contacteer uw dealer voor de aanschaf van
een draadloze hartslagmeter.
• Gebruik de draadloze hartslagmeter nooit in combinatie met
de handsensoren om storing te voorkomen.
WAARSCHUWING!
• Indien u een pacemaker heeft raden wij aan uw huisarts te
raadplegen voordat u een draadloze hartslagmeter gebruikt.
• In ruimte met meerdere hartslagmeter raden wij aan
voldoende afstand te houden om storing tussen verschillende
apparaten te voorkomen.
• Probeer de draadloze hartslagmeter altijd binnen een bereik
van 1 meter vanaf het console te houden voor een optimaal
ontvangst.
• Draag een draadloze hartslagmeter altijd direct op het
lichaam, onder de kleding.