Vision Fitness T9000 User manual

Assembly
Guide
T9100 AND T9000
PLATFORM TREADMILLS

1
STEP
2
STEP
4
STEP
To avoid possible damage to this treadmill, please follow these assembly steps in the correct order. Before proceeding, find your
new treadmill’s serial number located on the front axle tube, and enter here:
Please, refer to this number when calling for service. Enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your
treadmill to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially
threaded in before completely tightening any ONE screw or bolt.
Assembly
Guide
T9100 AND T9000
PLATFORM TREADMILLS
3
STEP

6MM Allen Wrench
Screwdriver
5MM L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Water Bottle, Qty: 1
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card

ORANGE BAG
BLUE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 20L Screws
Quantity: 2
M8 x 65L Screw
Quantity: 6
M8 x 20L Screws
Quantity: 4
M5 x 20L Panhead Screw
Quantity: 4

5
1
STEP
• Insert one of the console supports
into the console support bracket and
secure with three bolts (M8x65L) in the
side of the console support bracket.
• Secure the rear of the console
support using bolt (M8x20L)
• Use the 5mm L-shaped Allen wrench
to tighten all bolts.
• Repeat this step on the opposite
side. NOTE: The right console support
has a white wire tie attached to it.
ORANGE BAG
1
STEP
2
STEP
• Slide the data cables down the right
console support using the white wire
tie as a guide. Make sure that the
data cables come out the hole in the
side of the console support.
• Mount the console to the console
mast using the four flathead bolts
(M8x20L) and tighten with the blue
handled 5mm L-shaped Allen wrench.
NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.
BLUE BAG
2
STEP

6
3
STEP
• Plug the large data cable into the
large plug connection on the lower
control board. Plug the small data
cable into the small plug connection
on the lower control board.
• Install the motor cover. Secure the
motor cover using the four (M5x20L)
screws.
PINK BAG
3
STEP
4
STEP
• Once the treadmill is plugged
in, you need to perform an Auto-
Calibration to assure maximum
performance.
DO NOT STAND ON THE
BELT WHEN PERFORMING THE
AUTO-CALIBRATION
• With the SAFETY KEY in place, hold
the ELEVATION UP and SPEED
DOWN buttons for five seconds. The
console will beep twice, “ENG0” will
appear in the Distance window, and
a number will apear in the Elevation
window.
• Press SELECT until “ENG3”
appears; this is for Auto-Calibration.
Press START to Auto-Calibrate.
• The treadmill will calibrate minimum
and maximum speed, and minimum
and maximum elevation. When Auto-
Calibration is complete, the treadmill
will reset to User’s start screen. This
process takes three to five minutes.
AUTO CALIBRATION

7
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 10.03 Part #Z90TM78-AG18.27PRD
AG18.27PRD
REV2
5
STEP
• If the running belt slips when used,
use the supplied 6mm Allen wrench to
turn the left and right tension bolts
clockwise 1/4 turn at a time until the
belt no longer slips.
• If the running belt is too far to the
right side, use the supplied 6mm Allen
wrench to turn the right tension bolt
clockwise 1/4 turn at a time until the
belt stays centered during use. If the
running belt is too far to the left side,
turn the left tension bolt clockwise
1/4 turn at a time until the belt
remains centered during use.
BELT TENSION
5
STEP