Vision Fitness T9800 Series User manual

Assembly
Guide
T9800 Series
TREADMILLS

1
STEP
2
STEP
6
STEP
To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct order. Before proceeding
though, find your new Platform Treadmill’s 2 serial numbers, located on the underside of the main frame, and on the bottom of the
console, and enter here:
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty Card and in your own
records. Be sure to read your Owner’s Guide before using your new Platform Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform Treadmill, to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
Assembly
Guide
T9800 Series
TREADMILLS
3
STEP
4
STEP
Frame Serial Number Console Serial Number

Screwdriver
TOOLS, HARDWARE, & PARTS INCLUDED
PARTS BOX
Water Bottle, Qty: 1
Handlebars, Qty: 2
Handlebar Covers, Qty: 2
Power Cord, Qty: 1
Color-coded Hardware Bags
5mm L-Shaped Wrench
6mm L-Shaped Wrench
8mm T-Shaped Wrench

HARDWARE INCLUDED
ORANGE BAG BLUE BAG
M10 x 20L Bolt
Quantity: 4
PINK BAG
M8 x 15L Socket Head
Quantity: 8
8.2x19x2T Flat Washer
Quantity: 8
10.2x19x2T Flat Washer
Quantity: 4
M8 x 15L Socket Head
Quantity: 4
8.2x19x2T Flat Washer
Quantity: 4
M8 x 15L Flat Head
Quantity: 2
6x20x2T Flat Washer
Quantity: 4
6x13x2T Arc Washer
Quantity: 2
M6 x 15L Socket Head
Quantity: 6
M5 x 12L Phillips Head
Quantity: 2

5
1
STEP
1
STEP
• Remove motor cover screws and
take off the motor cover.
• Insert the right console mast to the
right console mast bracket. First, fasten
the inside of the console mast to the
console mast bracket by securing four
bolts (M8x15L socket head) and four
washers (8.2x19x2T). Fully tighten the
bolts. Second, fasten the two bolts
(M10x20L button head) and two
washers (10.2x19x2T) on the front of
the console mast and fully tighten.
• Repeat on the left side
ORANGE BAG
2
STEP
• Tie the ribbon data cable to the
cable wire tie on the top of the right
console mast. Feed the ribbon cable
down the console mast and through the
hole at the lower part of the console
mast. Push any remaining cable into
the console mast.
• Mount the console onto the left and
right console masts using four bolts
(M8x15L socket head) and four washers
(8.2x19x2T). Do not fully tighten.
• Take the wire tie off the ribbon
cable. Plug the large 20-pin ribbon
connector into the 20-pin connector
on the lower control board. Attach the
two grounding wire connectors to the
two grounding wires located in the
motor pan near the front of the frame.
BLUE BAG
2
STEP

6
3
STEP
3
STEP
• Insert the handlebar cover onto the
handlebar. Insert the right handlebar
by holding the handlebar sideways
toward the treadmill and inserting the
top into the console. Rotate the
handlebar into the bracket located on
the console mast. Fasten with a bolt
(M5x12L), and a bolt (M6x15L socket
head) & an arc washer (6x13x2T) into
the two holes of the console plastic,
and a bolt (M8x15L flat head) into the
hole in the handlebar. Fasten a bolt
(M6x15L socket head) and a flat washer
(6x20x2T) into the hole in the handlebar
on the console mast. Do not fully tighten
the bolts.
• Slide the handlebar cover over the
bracket and secure with a bolt
(M6x15L socket head) and a flat
washer (6x20x2T). Do not fully tighten
the bolt.
• Repeat on the left side.
• Fully tighten the console and
handlebar bolts.
PINK BAG
4
STEP
• Place the motor cover back on the
frame and fasten with 6 screws.
• Attach the power cord to the treadmill.
• Plug the power cord into the power
outlet.
MOTOR COVER
4
STEP

7
4
STEP
DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION
You need to access User Engineering Mode to run the auto-calibration.
With the safety key in place , please hold
down SPEED DOWN and SELECT for 5 seconds. When in the User mode,
“USER ENG MODE” appears in the
alphanumeric window. To access the data press the ELEVATION keys until
“AUTO-CALIBRATION” appears.
To begin auto-calibration, press SELECT. The treadmill will run through minimum and maximum speed and
maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the
Engineering Mode.
Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in
the right window.
“CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is
complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.
AUTO-CALIBRATION

8
500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2006 Vision Fitness. All Rights Reserved. 2.06
AG18.39PRD
REV5
6
STEP
6
STEP
• If the running belt slips when used,
run the treadmill at 2.0 mph and use
the supplied 8mm Allen wrench to turn
the left and right tension bolts clockwise
1
/4-turn at a time until the belt no
longer slips.
• If the running belt is too far to the
right side, run the treadmill at 2.0 mph
and use the supplied 8mm Allen
wrench to turn the right tension bolt
clockwise
1
/4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the left
side, run the treadmill at 2.0 mph and
turn the left tension bolt clockwise
1
/4-turn at a time until the belt remains
centered during use.
BELT TENSION