Vision Fitness T9700HRT Use and care manual

Date of last revision: 12.03
CALIBRATION GUIDES
1
TREADMILL.CALIB.REV1
T9700HRT v1.7-2.0
Calibration Guide
STEP 1 ENTER ENGINEERING MODE
• With the SAFETY KEY in place, hold the “ELEVATION UP” and
“SPEED DOWN” buttons for 5 seconds. ““NNOONNEE””will appear in the
profile window.
• Press
“SPEED UP” until ““CCOONNFFIIGGUURREE””appears in the profile window.
Press “SELECT” .
• You are now in ENGINEERING MODE.
STEP 2 SET MINIMUM SPEED
• ““PP00MMIINNSSPPEEEEDD””will appear in the scrolling window. ““00””should
appear in the elevation window and ””3333””should appear in the
speed window. To adjust, Press
“START” .
• Press the
“SPEED UP” or “SPEED DOWN” button until the elevation
window reads ““3311--3355””. The running belt should be moving at .5 MPH.
• Press the
“SELECT” button to update the data.
STEP 3 SET THE HALF MAXIMUM SPEED
• Press the “ELEVATION UP” button until the scrolling window reads
““PP1111//22MMAAXX””. ““00””will appear in the elevation window and ““116666””will
appear in the speed window. To adjust, press
“START” .
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the elevation
window reads ““116633--116699””. The running belt should be moving at 6 MPH.
• Press the
“SELECT” button to update the data.
STEP 4 SET MAXIMUM SPEED
• Press the “ELEVATION UP” button until the scrolling window reads
““PP22MMAAXXSSPPEEEEDD””. ““00””will appear in the elevation window and ““332200””
will appear in the speed window. To adjust, press
“START” .
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the elevation
window reads ““331177--332200””. The running belt should be moving at 12 MPH.
• Press the
“SELECT” button to update the data.
STEP 5 SET MINIMUM ELEVATION
• Press the “ELEVATION UP” button until the scrolling window reads
““PP44EELLEEZZEERROO””. ““5599””will appear in the elevation window and ““5599””will
appear in the speed window.
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the elevation
window reads ““5566--6622””. The treadmill should be level.
• Press the
“SELECT” button to update the data.

Date of last revision: 12.03
CALIBRATION GUIDES
2
TREADMILL.CALIB.REV1
T9700HRT v1.7-2.0
Calibration Guide continued
STEP 6 SET MAXIMUM ELEVATION
• Press the “ELEVATION UP” button until the scrolling window reads
““PP55EELLEEMMAAXX””. ““5599””will appear in the elevation window and ““221166””will
appear in the speed window.
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the elevation
window reads ““221133--221199””. The treadmill will be at maximum elevation.
STEP 7 SAVING THE VALUES
• Press the “ELEVATION UP” button until the scrolling window reads
““PP66TT99770000HHEE””. ““11..88””will appear in the elevation window and ““88””will
appear in the speed window.
• Press the
“SELECT” button to store the data.
• Press the
“START” button to save the data.
REMOVE AND REPLACE THE SAFETY KEY.
PRESS THE START BUTTON AND TEST THE TREADMILL.
SPECIAL NOTES
P7 Max Time Maximum program time 99 15 99
P8 Weight Weight used for calories 150 35 400
P9 OP Hours Accumulated Hours 0 0 6553
P10 OP Dist Accumulated distance 0 0 6553
P11 BELT Belt thickness in mm 5 0 10
P12 Roller Roller Diameter in mm 60 60 60
P13 ELV DIR Elevation Pot inverter 255 0 255
P14 EL ERRS Toggles Elev errors on & off 0 0 1
P15SCROLL Sets speed of scroll 7 1 255
P16CURRENT Toggles current sensing on & off 1 0 1
P17LUBE HRS # of Hrs. since last lube 0 0
P18 Clean Dist. since last cleaning 0 0
P19 Brush Dist. since brushes have been replaced 0 0
NOTES: If the elevation is not working, there are no errors, and it is still calibrating check to see if P14 is on or off.
P16 turns off the current sensors.
P17-P19-must be reset after the service is performed. To reset, hold down the
“STOP” key for 3 seconds. The console will
beep once and UPDATE will replace the text next to the P number then return to the original text when finished updating.