VISIONARY DESIGNS VK-3003 Manual

© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-3003 - 10’x30’ Inline Display
Plan View
Perspective View
30’
10’

© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
www.classicexhibits.com
Order #XXXXX General Information
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C

© 2017
www.classicexhibits.com
Order #XXXXX
Crate 1 of 1
Crate Packing

© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 8
Front Frame
12a 12b
13a 13b
15b
16
17
15a
14b
14a
Item
12a/12b
13a/13b
14a/14b
15a/15b
16
17
Qty.
1/1
1/1
1/1
1/1
1
1
Description
38.5”w Horizontal Extrusion
38.5”w Horizontal Extrusion
44.6” Curved Extrusion
44.6” Curved Extrusion
48”w Horizontal Extrusion
46.2573"w Horizontal Extrusion
Steps:
1) Attach vertical extrusions [14a,14b] & [15a,15b] together.
2) Connect horizontal extrusions [12a,12b] & [13a,13b] together.
3) Connect horizontals between assembled verticals.

© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 8
Backwall Assembly
When assembled
Item
3
4
9
10
11
Qty.
1
1
1
1
1
Description
48”h Round Vertical Extrusion
48”h Round Vertical Extrusion
41.7083” Curved Horizontal Extrusion
41.7083” Curved Horizontal Extrusion
Oval Base Plate
Remove A10’s for
10x20 & 10x30
Configuration
Steps:
1) Attach base plates to lower verticals using bolts as shown.
2) Attach upper verticals to lower verticals.
3) Connect curved horizontals together.
4) Attach curved horizontal assemblies between verticals.
3
4
11
11
9
10
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Plastic
Knob
Wing Attachment Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Attach graphic
to velcro on back of
assembled frame

© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 8
Backwall Assembly (cont’d)
When assembled
18
19
Steps:
1) Attach assembled SEG frame to backwall
using connectors [F] as show.
2) Velcro attach lights to back of SEG frame.
Velcro attach lights
to back of extrusion
facing the back
Velcro attach lights
to back of extrusion
facing the back
Velcro attach lights
to back of extrusion
facing the back
18
19

© 2017
www.classicexhibits.com
Order #XXXXX
Step 4 of 8
Backwall Attachments
Steps:
1) See details and attachments this sheet. Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
Attach wall plate to horizontal bars
using standoffs bolts and wing nuts
Hook monitor brackets over top of
wall plate, then secure with safety
bolts to bottom of monitor brackets.
Monitor Mount Attachment
Apply graphics before
monitor mount attachment.
Monitor
Mount
*
*
*
*

© 2017
www.classicexhibits.com
Order #XXXXX
Step 5 of 8
Left Backwall Assembly
2
3
1
11 11
8
8
7
7
Steps:
1) Attach base plates to lower verticals using bolts as shown.
2) Attach upper verticals to lower verticals.
3) Connect curved horizontals together.
4) Attach curved horizontal assemblies between verticals.
Item
1
2
3
7
8
11
Qty.
1
1
1
2
2
2
Description
96”h Round Vertical Extrusion
96”h Round Vertical Extrusion
96”h Round Vertical Extrusion
38”w Curved Horizontal Extrusion
76“w Curved Horizontal Extrusion
Oval Base Plate
Velcro
PR37
Extrusion
Profile
Attach graphic
to velcro on back of
assembled frame
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
***
Monitor Mount
Attachment
Attach back plate
to connectors using
screws. Attach top
plate and tighten
setscrews to secure.
Slide connectors
into groove of
extrusion. Tighten
setscrew to secure
in place.
Setscrews
*
*
*

© 2017
www.classicexhibits.com
Order #XXXXX
Step 6 of 8
Right Backwall Assembly
When assembled
Steps:
1) Attach base plates to lower verticals using bolts as shown.
2) Attach upper verticals to lower verticals.
3) Connect curved horizontals together.
4) Attach curved horizontal assemblies between verticals.
Item
5
6
7
8
11
Qty.
1
1
2
2
2
Description
96”h Round Vertical Extrusion
96”h Round Vertical Extrusion
38” Curved Horizontal Extrusion
76” Curved Horizontal Extrusion
Oval Base Plate
5
6
8
8
7
11
11
7
Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Attach graphic
to velcro on back of
assembled frame

© 2017
www.classicexhibits.com
Order #XXXXX
Step 7 of 8
Backwall Counter Assembly
When assembled
Item
20
21
22
23
24
25
22Door
Infill Infill Infill
HingeHinge HingeHinge
20 23
24
24
24
Shelf
Qty.2
Counter
24
21
Qty.
2
2
2
2
8
8
Description
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
13”w Horizontal Extrusion
10”w Horizontal Extrusion
Item
20
21
22
23
24
25
Qty.
2
2
2
2
8
8
Description
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
13”w Horizontal Extrusion
10”w Horizontal Extrusion
Steps:
1) Attach lower horizontals between verticals.
2) Attach door to vertical [23]. Refer to Door Attachment detail.
3) Slide infills between verticals as shown.
4) Attach upper horizontals between verticals.
5) Velcro attach shelf supports to inside of assembled pedestal.
6) Place shelf atop shelf supports.
7) Place counter atop assembled pedestal.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
25
25
25
25

© 2017
www.classicexhibits.com
Order #XXXXX
Step 8 of 8
Backwall Wing Attachments
Steps:
1) Attach graphics with A10 clips as shwon in Example of A10
Clamp Attachment detail.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.