VISIONARY DESIGNS VK-5095 User manual

© 2015
www.classicexhibits.com
Order #XXXXX - VK-5095
Perspective View
Perspective ViewPerspective View
Plan View
20’
20’

© 2015
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2015
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.



While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2015
www.classicexhibits.com
Order #XXXXX - Setup Instructions
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 1 of 12
Assembly A
2
1
A
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
1
1
1
1
1
1
Description
95.75”h TSP49 Vertical Extrusion
95.75”h TSP49 Vertical Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
92.1680”h
Z45 Vertical Extrusion
92.1680”h
Z45 Vertical Extrusion
48” TSP49 Curved Horizontal Extrusion
48” TSP49 Curved Horizontal Extrusion
Steps for assembly [A]:
1) Connect TSP49 frame extrusions [1-6] together.
Refer to TSV1 Lock Detail. See detail C, general
info page for horizontal connections.
2) Attach verticals [7,8] between TSP49 horizontals.
3) Attach horizontals [9,10] between verticals [7,8].
See detail C, general
info page for horizontal
connections.
4
6
8
7
9
10
3
5
When assembled
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
TSP49
Z45

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 2 of 12
Assemblies B & C
Item
11
12
13
14
15
16
17
18
19
20
21
22
23
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
95.75”h TSP49 Vertical Extrusion
95.75”h TSP49 Vertical Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
88.5151” TSP49 Curved Horizontal Extrusion
92.1680”h
Z45 Vertical Extrusion
92.1680”h
Z45 Vertical Extrusion
95.75”h TSP49 Vertical Extrusion
95.75”h TSP49 Vertical Extrusion
67.7067” TSP49 Curved Horizontal Extrusion
67.7067” TSP49 Curved Horizontal Extrusion
92.1680”h Z45 Vertical Extrusion
21
14
13
22
11
19
12
17
18
23 20
15
16
B C
Steps for assembly [B]:
1) Connect TSP49 frame extrusions [11-16] together.
Refer to TSV1 Lock Detail. See detail C, general
info page for horizontal connections.
2) Attach verticals [17,18] between TSP49 horizontals.
Steps for assembly [C]:
1) Connect TSP49 frame extrusions [19-22] together.
Refer to TSV1 Lock Detail.
2) Attach vertical [23] between TSP49 horizontals.
When assembled
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
TSP49
Z45
Custom Cam Lock
*
Top View
Cam Lock
Pill Slot
Pill
Slot
Tighten screw to clamp cam
lock into pill slot.
& Pill Slot Connection
*
*
*
See detail C,
general info
page for
horizontal
connections.

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 3 of 12
Assembly D
Item
24
25
26
27
28
29
Qty.
1
1
1
1
1
1
Description
48”h TSP49 Vertical Extrusion
48”h TSP49 Vertical Extrusion
96.5618” TSP49 Curved Horizontal Extrusion
96.5618” TSP49 Curved Horizontal Extrusion
44.4180”h Z45 Vertical Extrusion
44.4180”h
Z45 Vertical Extrusion
24
28
29
25
26
27
D
Steps for assembly [D]:
1) Connect TSP49 frame extrusions [24-27] together.
Refer to TSV1 Lock Detail.
2) Attach verticals [28,29] between TSP49 horizontals.
When
assembled
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
Z45
TSP49

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 4 of 12
Assembly E
Item
30
31
32
33
34
35
Qty.
1
1
1
1
1
1
Description
95.75”h TSP49 Vertical Extrusion
95.75”h TSP49 Vertical Extrusion
96.5618” TSP49 Curved Horizontal Extrusion
96.5618” TSP49 Curved Horizontal Extrusion
92.1680”h Z45 Vertical Extrusion
92.1680”h
Z45 Vertical Extrusion
30 34 35
32
33
31
E
Steps for assembly [E]:
1) Connect TSP49 frame extrusions [30-33] together.
Refer to TSV1 Lock Detail.
2) Attach verticals [34,35] between TSP49 horizontals.
When
assembled
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
Z45
TSP49

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 5 of 12
Assembly of Assembies
Item
36
37
38
39
40
41
42
43
44
45
Qty.
1
1
1
1
1
1
1
1
1
1
Description
Oval Base Plate
95.75”h S44 Vertical Extrusion
95.75”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion w/ Hinge
Oval Base Plate
95.75”h S44 Vertical Extrusion w/ Hinge
95.75”h S44 Vertical Extrusion
Oval Base Plate
95.75”h S44 Vertical Extrusion
48”h S44 Vertical Extrusion
36
41
41
37
39
42
A
B
D
E
C
38
44
45
40
43
*
39
Steps:
1) Attach base plates [36,40,43] to lower verticals [37,41,44]
using bolts as shown.
2) Attach upper verticals [38,42,45] to lower verticals [37,41,44].
3) Attach lower assembled SEG frames [A,D] between verticals
[37,39,44]. Refer to custom cam lock detail.
4) Attach upper assembled SEG frames [B,C,E] between verticals
assemblies. Refer to custom cam lock detail. Note: Connect
upper SEG frames to lower SEG frames using bolts and wing
nuts as shown.
5) Attach iPad mount to vertical [44]. Refer to detail.
When
assembled
Top View
Cam Lock
Tighten screw to
clamp cam lock
into groove of
vertical extrusion.
Custom
Cam Lock
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
S44
Swivel
Mounting
Plate
iPad Mount Attachment
*
Hex
Nuts
Swivel
Mounting Plate
Bolt iPad clamshell to
mounting plate with hex nuts.
Attach connector piece to iPad
mount as shown. Then connect
assembled iPad mount to vertical
extrusion.
Tighten Lock
to Secure

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 6 of 12
Assembly F1, F2, F3
Item
46a
47a
49a/49b
50
50a
Qty.
1
1
2/2
6
2
Description
96”h TSP49 Vertical Extrusion
96”h TSP49 Vertical Extrusion
96”h TSP49 Vertical Extrusion
22.9301” TSP49 Curved Horizontal Extrusion
19.2098” Z45 Curved Horizontal Extrusion
46a
47a
49b
49a
49b
49a
50
50
50
50
50
50
50a
50b
50a
50b
When
assembled
F1 F2
F3
F1
F2
F3
Steps for assembly [F1]:
1) Connect TSP49 frame extrusions [46a,49a,50]
together. Refer to TSV1 Lock Detail.
2) Attach horizontal [50a] between TSP49 verticals.
Steps for assembly [F2]:
1) Connect TSP49 frame extrusions [49a,49b,50]
together. Refer to TSV1 Lock Detail.
Steps for assembly [F3]:
1) Connect TSP49 frame extrusions [47a,49b,50]
together. Refer to TSV1 Lock Detail.
2) Attach horizontal [50a] between TSP49 verticals.
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
TSP49

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 7 of 12
Closet Room Assembly
Item
39
46
47
48
49
Qty.
1
1
1
2
2
Description
96”h S44 Vertical Extrusion w/ Hinge
96”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion w/ Hinge
27.4515” Z45 Curved Horizontal Extrusion
96”h S44 Vertical Extrusion
46
49
49 47
Item #39 - Main Structure
Infill
Door
When
assembled
Plan View
47
39
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Hinge
Hinge
Door Threshold
Tighten setscrew
to secure
Slide Connector
into Groove
of Extrusion
Door
Threshold
48
48
F1
F2
F3
Steps:
1) Attach assembled SEG frames [F1,F2,F3] between verticals
[46,47,49]. Refer to custom cam lock detail.
2) Attach door threshold between verticals [47,39]. Refer to detail.
3) Attach door to vertical [39]. Refer to detail.
4) Attach upper curved horizontals [48] and place infill between verticals.
Top View
Cam Lock
Tighten screw to
clamp cam lock
into groove of
vertical extrusion.
Custom
Cam Lock
*
*
*
*
*
*
*
*
*
*
*
*
*
******

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 8 of 12
Assembly G
GG
G
Item
46
51
52
53
54
55
56
Qty.
1
1
1
1
1
1
1
Description
96”h S44 Vertical Extrusion
96”h TSP49 Vertical Extrusion
96”h TSP49 Vertical Extrusion
66.6995” TSP49 Curved Horizontal Extrusion
66.6995” TSP49 Curved Horizontal Extrusion
Round Base Plate
95.75”h S44 Vertical Extrusion
46
52
53
54
Plan View
Main Structure
Main Structure
51
55
56
Steps for assembly [G]:
1) Connect TSP49 frame extrusions [51-54]
together. Refer to TSV1 Lock Detail.
2) Attach base plate [55] to vertical [56] using a bolt.
3) Attach assembled SEG frame [G] between verticals
[46,56]. Refer to custom cam lock detail.
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
Top View
Cam Lock
Tighten screw to
clamp cam lock
into groove of
vertical extrusion.
Custom
Cam Lock
*
*
*
*
*
*
*

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 9 of 12
Attachments
*
Steps:
1) Attach monitor mount to frame [A]. Refer to detail.
2) Apply SEG graphics to TSP49 frames [A-G].
See attached SEG graphic installation for graphic attachment
3) Attach lights atop assembled backwall. Refer to detail.
****See attached SEG graphic
installation for graphic attachment
G
F1
F2
F3
A
A
D
E
C
BPlan View
Attach wall plate to
horizontal bar using
standoffs and wing nuts
Hook monitor brackets over
top of wall plate, then secure
with safety bolts to bottom
of monitor brackets.
Monitor Mount Attachment
*
*
*
*
**
*
*
**
*
*
**
*
Slide light into light
receiving hardware
Lock into
groove of
horizontal
Lock Light Receiving
Hardware into Groove
of Horizontal Extrusion
Example of Light Attachment

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 10 of 12
Shelves Attachments
Item
57
58
58a
59
60
Qty.
1
2
2
2
2
Description
82.7624” Z45 Curved Horizontal Extrusion
40”h S44 Vertical Extrusion
Base Plate
19” Z45 Curved Horizontal Extrusion
19” Z45 Curved Horizontal Extrusion
58
59
60
57
Shelf Pin Location
Shelf
Shelf
Counter
Qty.2
58a
Base Plate
*
*
*
*
*
*
**
*
*
*
*
*
*
*
*
*
*
*
*
*
Steps:
1) Attach verticals [58] to base [58a] using screws as shown .
2) Attach curved horizontals [59,60] to verticals [58] as shown.
3) Attach curved horizontals [59,60] to backwall verticals [46 & 49] and [49 & 47].
4) Place shelves on shelf pins between verticals and wall as shown.
5) Place countertop on top of assembled shelving unit as shown.
6) Attach curved horizontal [57] between verticals [47 & 41] as shown.
46
49
49 47
41
47 57 57
41
*
Bolt
50b
Monitor Mount Attachment
Attach monitor mount to horizontal
extrusion using bolts and wing nuts.
Wing
Nut

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 11 of 12
MOD-1289 Pedestal
When
assembled
61
62
63 65
63
1
2
Infill
Infill
Infill
65
64
66
64
Door
Shelf
(4) Shelf
Supports
Counter Top
Counter
Item Qty Description
61 1 38” S44 Vertical Extrusion
62 1 38” S44 Vertical Extrusion
63 2 41.2385” Z45 Curved Horizontal Extrusion
64 2 41.2385” Z45 Curved Horizontal Extrusion
65 2 16.35” Z45 Horizontal Extrusion
66 1 34.41” Z45 Vertical Extrusion w/ Door Hinges
Item Description
15.75”r x 42“h Half Curve Panel
25.75”r x 42“h Half Curve Panel
Steps:
1) Attach curved panels [1,2] together.
2) Attach lower horizontals [63,64,65] between
assembled curved panels and verticals [61,62].
3) Attach vertical [66] to lower horizontal [64], Placing
infill as shown.
4) Insert infills as shown.
5) Attach upper horizontals [63,64,65] between
assembled curve panels and verticals [61,62] atop infills.
6) Hang door from hinges as shown in detail.
7) Place internal shelf on shelf supports
8) Set counter tops on top of assembled base.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 12 of 12
MOD-1290 Pedestal
Item
67
68
69
70
Qty.
1
1
2
2
Description
40” GS220 Corner Vertical Extrusion
40” GS220 Corner Vertical Extrusion
23” Z45 Horizontal Extrusion
40.0695” Z45 Curved Horizontal Extrusion
Steps:
1) Attach lower horizontals [69,70] between verticals [67,68].
2) Attach door to vertical [67]. Refer to Door Attachment detail.
3) Attach upper horizontals [69,70] between verticals [67,68].
Note: Place infill between verticals and curved horizontals.
4) Velcro attach shelf supports to inside of assembled pedestal.
5) Place internal shelf on shelf supports.
6) Set counter top on top of assembled pedestal.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
When
assembled
67
68
69
70
Shelf
Shelf
Supports
Counter
69
70
Door
Infill