Vivo STAND-V102AF User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102af
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V102AF

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x1)
Decorative
Cover
c(x1)
Monitor Arm
a(x1)
48mm Pipe
e(x3)
M6x29
l(x8)
M4x12
k(x1)
Spring Washer
j(x1)
M10 Washer
i(x1)
Support Plate
f(x2)
M8x10
b(x1)
Weighted Base
g(x4)
Wire Clip
h(x1)
M10 Bolt
p(x2)
Spare Cap
o(x2)
Nut
n(x8)
M4 Spacer
m (x8)
M4x30
s(x2)
VESA Plate
r (x1)
Wrench
q (x1)
Allen Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
OPTION 1:
Install the weighted base (b) to the 48mm Pipe
(a) using M6x29 Bolts (e). Install the Decorative
Cover (d).
TOOLS NEEDED
22lbs
Per Monitor
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION 2:
Position the 48mm Pipe (a) on the mounting
surface and mark the center hole. Remove the
tube support. Drill a 3/8” (10mm) diameter hole
at the marked position through the mounting
surface. If using an existing grommet hole,
remove the plastic cover if present to ensure a flat
surface before installing the desk mount. Position
the 48mm Pipe (a) on the mounting surface and
secure using the Support Plate (i), M10 Washer
(j), Spring Washer (k) and M10 Bolt (h). Fasten
the M10 Bolt with provided Wrench (r). Install the
Decorative Cover (d).
a
b
d
e
a
d
i
h
j
k
a
d
b
e
i
h
j
k
OPTION 3:
Position the 48mm Pipe (a) on the mounting surface
and mark the center hole. Remove the tube support.
Drill a 3/8” (10mm) diameter hole at the marked
position through the mounting surface. If using an
existing grommet hole, remove the plastic cover if
present to ensure a flat surface before installing the
desk mount.
Install the weighted base (b) to the 48mm Pipe (a)
using M6x29 Bolts (e), then install the Decorative
Cover (d). Position assembled pole with base on
the mounting surface and secure using the Support
Plate (i), M10 Washer (j), Spring Washer (k) and M10
Bolt (h). Fasten the M10 Bolt with provided Wrench
(r).
Drill

4
STEP 2
Carefully slide monitor arm (c) onto 48mm pipe (a), making sure the cable clips are facing down.
Secure with M8x10 bolts (f) using a Phillips screwdriver or Allen wrench (q).
STEP 3
OPTION A: Flat Back Monitor
Attach VESA Plates (s) to monitor using M4x12 Thumb Screws (l). Please note, the screws only need
to be finger-tight.
~
ÖÑ
s
l
gq
f
a

5
STEP 3 (Continued)
OPTION B: Curved Back TV
Attach VESA Plates (s) to monitor using M4x30 Screws (m) with M4 Spacers (n). Do not over-tighten.
STEP 4
Slide the monitors onto the heads of Monitor Arm (c) as shown in the diagram. Install the Security
Nuts (o). Make sure the security nuts are installed before you rotate the monitors.
n
m
s

6
STEP 5
STEP 6
Pry o the plastic cover and then use the Wrench (r) to tighten the nut if the tilt angle can not be
fixed. Remove the Nut (o) and turn the bolt counter-clockwise with supplied Allen Wrench (q) to
raise the monitor. Reinstall the Nut aer the adjustment.
Pry o the arm cover, then use the Allen Wrench (q) to adjust the swivel joint tension.
q

7
STEP 7
Manage the wires.

Last Updated: 09/06/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654