Vivo STAND-TV120B User manual

Aluminum Mobile Large Screen TV Cart
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv120b
SKU: STAND-TV120B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Le Leg
B(x1)
Right Leg
C(x1)
Base
I (x1)
Media Shelf
J x1)
Le TV Bracket
K(x1)
Right TV Bracket
L (x1)
Camera Shelf
H(x1)
Mounting Plate
D (x4)
Caster
E (x2)
Lower Column
F (x2)
Upper Column
G (x2)
Handle
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
N (x2)
End Cap
M(x1)
Camera Shelf
Support
O x2)
Top Cover
S-F (x1)
Spacer
T-C (x1)
M6 Wrench
S-E (x2)
M8x12mm Screw
S-A (x8)
Washer
S-B (x8)
M8x80mm Screw
S-D (x2)
M5x8mm Screw
T-D (x1)
M12 Wrench
S-C (x16)
M8x20mm Screw
T-A (x1)
5mm Allen
Wrench
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
M-G (x8)
Small Spacer
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT
SUPERVISION IS REQUIRED.
P x16)
Cable Cover
T-B (x1)
6mm Allen
Wrench
M-H (x8)
Large Spacer

3
ASSEMBLY STEPS
STEP 1
Attach Le Legs (A) and Right Leg (B) to Base (C) using M8x20mm Screws (S-C) and 6mm Allen Wrench
(T-B) as shown in the figure below. Then attach Casters (D) to the legs using M12 Wrench (T-D).
308lbs
(140kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
TOOLS NEEDED
TV
11lbs
(5kg)
MEDIA SHELF
11lbs
(5kg)
CAMERA SHELF
A
B
T-B
S-C
C
S-C
D
T-D

4
STEP 2
Attach Lower Columns (E) to the assembled base using M8x80mm Screws (S-B) with Washers (S-A)
and 6mm Allen Wrench (T-B). Assemble Upper Columns (F) to Lower Columns (E) using M8x20mm
Screws (S-C) and 6mm Allen Wrench (T-B) . Then slide the Handles (G) over Upper Columns (F) as
shown below.
E
S-B
S-A
T-B
T-B
G
FS-C

5
STEP 3
Loosen the 8 screws shown below on Mounting Plate (H) using 5mm Allen Wrench (T-A). Then slide
Mounting Plate (H) down onto Upper Columns (F) and retighten the 8 Screws.
Note: There is a gap between the brackets on Mounting Plate (H) and the top of the plate. This gap
should be on top when installed. Top
H
T-A
F

6
STEP 5
Loosen the two screws on both of the upright brackets on Media Shelf (I) using 5mm Allen Wrench
(T-A). Then slide Media Shelf (I) down into the groove on Lower Columns (E) and then retighten the
four screws at the desired height.
STEP 4
Press on Top Covers (O) into Upper Columns (F) and End Caps (N) onto Mounting Plate (H) as shown
below.
O
F
N
H
I
T-A
E

7
STEP 6
Assemble Le TV Bracket (J) and Right TV Bracket (K) to the back of the television using Screws (M-A
through M-E) with Square Washers (M-F) and Spacer (M-G, M-H).
KJ

8
STEP 7
Hang the TV with Le TV Bracket (J) and Right TV Bracket (K) onto Mounting Plate (H). Secure it by
tightening the security screw on the bottom of the TV brackets using a Phillips screwdriver.
JK
H

9
STEP 8
Attach Camera Shelf (L) to Camera Shelf Support (M) using M5x8mm Screws (S-D) and a Phillips
screwdriver. Then mount Shelf Support (M) at the desired height on Mounting Plate (H) using
M8x12mm Screws (S-E) with Spacer (S-F) and 5mm Allen Wrench (T-A), making sure the spacer goes
between Camera Shelf Support (M) and Mounting Plate (H) in the bottom hole as shown below.
L
M
S-D
H
S-E
S-F
T-A

10
STEP 9
Route cables through the provided slots in the columns and attach the Cable Covers (P) to hold them
in place. Store the Allen Wrenches (T-A, T-B) in the holes in Handles (G).
P
T-A
T-B
G

11
STEP 10
NOTE: Height marking represents the distance from the floor to the center of the brackets (this
includes the casters).

LAST UPDATED: 02/02/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303