Vivo MOUNT-M-MM070A User manual

Mechanical Spring Fireplace TV Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-m-mm070a
SKU: MOUNT-M-MM070A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Mount
B(x1)
Wall Plate
C(x1)
Stencil
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
TV Plate
E (x2)
VESA Bracket
F (x1)
Handle Support
G (x1)
Handle
H(x2)
Wall Plate Cover
I(x1)
TV Plate Cover
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x4)
M8x12mm Screw
S-B (x3)
M8 Plastic Washer
S-C (x3)
M8 Washer
S-E (x4)
ST3x6mm Screw
S-F (x2)
M6x10mm Screw
S-G (x2)
M6x20mm Screw
S-H (x4)
M6 Washer
S-D (x3)
M8 Nut
M-G (x8)
Small Spacer
M-H (x8)
Large Spacer
W-A (x6)
ST6.3x55mm Screw
W-C (x6 )
M6 Washer
W-B (x6)
Concrete Anchor
T-A (x1)
5mm Allen Wrench
T-B (x1)
Ratchet
T-C (x1)
Socket
T-D (x1)
Wrench

3
ASSEMBLY STEPS
STEP 1
Assemble Mount (A) to Wall Plate (B) using M8x12mm Screws (S-A) and 5mm Allen Wrench (T-A).
28.6-72.6lbs
(13-33kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
3/8” Bit
Pencil Phillips
Drill
3/16” Bit
Tape
Measure Stud Finder
A
BS-A
T-A
Level
STEP 2
Measure the required mounting height using the
chart below. Ensure the front edge of the mantel
does not exceed 110°F (43°C).
(1.2”)
(7.9”)
(9.9”)
(11.8”)
(13.8”)
(1.2”)
(7.9”)
(5.5”)
(6.7”)
(9.9”)

4
STEP 3 (Option A)
Wood Wall Installation
Use Stencil (C) to mark mounting holes on the wall where a stud is located, and drill 55mm (2.2”) deep
holes using 4.5mm (3/16”) bit. Use of a stud nder and level is recommended. Mount Wall Plate (B) to
the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C). Do not use Concrete Anchors (W-B) for
wood stud or drywall installation.
STEP 3 (Option B)
Concrete/Brick Wall Installation
Use Stencil (C) to mark mounting holes on the wall. Using a 10mm (3/8”) drill bit, drill holes at least
60mm (2.4”) deep into marked locations. Use of a level is recommended. Press Concrete Anchors (W-B)
into holes. Mount Wall Plate (B) to the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C).
C
B
W-A
W-C
W-B
C
W-B B
W-A
W-C

5
STEP 6
Assemble TV Plate Cover (I) to TV Plate (D) using ST3x6mm Screws (S-E) and a Phillips screwdriver.
I
D
S-E
STEP 4
Install Wall Plate Covers (H) to Wall Plate (B).
H
B
STEP 5
Secure TV Plate (D) to Mount (A) using M8 Plastic Washers (S-B), M8 Washers (S-C), and M8 Nuts (S-D).
Tighten M8 Nuts (S-D) using Wrench (T-D).
D
A
S-B
S-C
S-D
T-D

6
STEP 9
STEP 8
Assemble Handle Support (F) to VESA Brackets (E) using M6x20mm Screws (S-G) and M6 Washers
(S-H). Mount Handle (G) to Handle Support (F) using M6x10mm Screws (S-F) and M6 Washers (S-H).
Tighten all screws using 5mm Allen Wrench (T-A).
Level Mount (A) and insert 5mm Allen Wrench (T-A) into the
of the end to lock it in place. Remove Nuts (E1) from the back
of VESA Brackets (E) using Wrench (T-D) and open the latches.
Hang VESA Brackets (E) over TV Plate (D) and secure the
latches using Nuts (E1) and Wrench (T-D).
D
T-A
E1
E
T-D
A
Latch
STEP 7
Attach VESA Brackets (E) to back of the TV
using screws (M-A through M-E) and Square
Washers (M-F). If screws are too long, spacers
(M-G, M-H) may be required.
E
F
E
S-G
S-HGS-H
S-F
T-A

7
STEP 10
STEP 11
Assemble Socket (T-C) to Ratchet (T-B). Insert Socket (T-C) into the adjustment screw on the front of
Mount (A). Tighten the adjustment screw using Ratchet (T-B) to set the the indicator to the correct
position based on the weight of the TV.
A
T-B
T-C
Adjustment
Screw Indicator
Organize cables using the cable clips located under Mount (A). Remove 5mm Allen Wrench (T-A) from
Mount (A) and adjust the TV as desired.
T-A
A

LAST UPDATED: 03/28/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303