Vivo STAND-V032T User manual

Dual Monitor Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v032t
SKU: STAND-V032T
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Lower Pole
F (x2)
VESA Plate
S-A (x3)
M6x16mm
Screw
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
S-B (x2)
M6 Security
Nut
M-A (x8)
M4x12mm
Thumb Screw
M-B (x8)
M4x30mm
Screw
M-C (x8)
M6 Spacer
G (x1)
Pole Cap
H (x3)
Pole Cable
Clip
I (x4)
Cable Clip
J (x1)
Grommet
Plate
K (x1)
So Pad
L (x1)
Support Plate
B (x1)
Middle Pole
C (x1)
Upper Pole D(x1)
Clamp
E(x1)
Mount Arms
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
STEP 1
STEP 2: Option A - Desk Clamp
Loosen knob on Clamp (D), as shown below.
Connect Clamp (D) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
Place assembly on desktop and secure by tightening knob on Clamp (D).
D
T-A
S-A
DD
A
Lower Pole (A) & Upper Pole (C) may look similar.
To dierentiate, match the hole pattern to images below:
Lower Pole Upper Pole
(A) (C)

4
STEP 2: Option B - Grommet
Using a phillips screwdriver, remove the screw from Clamp (D) and disassemble. Set Knob (D1)
aside. Connect Grommet Plate (J) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen
Wrench (T-A). Remove adhesive backing from So Pad (K) and adhere to Grommet Plate (J).
Place the pole assembly over grommet hole in desk, and connect using Support Plate (L) and
previously removed Knob (D1) from underneath desk, as shown. Secure by tightening Hand Bolt
(D1). For desktops without an existing gromment hole, use a 3/8” (10mm) drill bit to drill through
desktop, then secure assembly as previously described.
L
L
D1
D1
EXISTING
GROMMET HOLE
DRILLING A
GROMMET HOLE
Lower Pole (A) & Upper Pole (C) may look similar.
To dierentiate, match the hole pattern to images below:
Lower Pole Upper Pole
(A) (C)
A
J
S-A
K
T-A

5
C
B
A
STEP 3
Tighten and secure Middle Pole (B) to Lower Pole (A), then connect Upper Pole (C) to Middle Pole (B).
STEP 4
Slide Pole Cable Clips (H) over pole assembly, then attach Mount Arms (E) and secure using 6mm
Allen Wrench (T-C). Press Pole Cap (G) into pole assembly.
Attach Cable Clips (I) to Monitor Arms (E) by snapping into place.
E
G
H
T-C
I

6
STEP 5
OR
Secure VESA Plates (F) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B).
M6 Spacers (M-C) may be required.
Slide monitors with VESA Plates (F) onto Mount Arms (E). Secure VESA Plates (F) in place using
M6 Security Nuts (S-B).
Route cables through Cable Clips (I) and Pole Cable Clips (H).
M-A
FF
FE
M-B
M-C
STEP 6
S-B
I
H

7
STEP 7
Adjust the monitor tilt using 5mm Allen Wrench (T-B). To level monitors, remove M6 Security Nuts
(S-B) and tighten or loosen adjustment screws using 3mm Allen Wrench (T-A). Once level, fasten M6
Security Nuts (S-B) back into place.
T-B
S-B
T-A

LAST UPDATED: 11/14/2022
REV1.1
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303