Vivo STAND-TV00J User manual

Tabletop TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv00j
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-TV00J

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
80lbs
(36.3kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
TV Plate
B(x2)
Monitor Bracket
C(x1)
Tempered
Glass
J (x2)
Wire Clip
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Support
Column
E(x2)
Plastic Socket
F (x1)
Metal Pad
G(x4)
M6x10
H (x4)
Metal Washer
I (x3)
M8x22
K (x4)
Rubber Foot
L(x4)
M4x12
M(x4)
M4x30
N(x4)
M6x20
O (x4)
M6x35
P (x4)
M8x20
Q(x4)
M8x35
R (x4)
M4 Washer
S(x4)
M6 Washer
T (x4)
M8 Washer
U (x4)
M4 Spacer
V(x8)
M6/8 Spacer
W(x1)
Allen Wrench
Stick rubber feet (K) to bottom of tempered glass (C). Attach support column (D) to tempered glass
(C) with plastic socket (E) in between and metal pad (F) underneath. Use bolt (I) to secure assembly.
Tighten using allen wrench (W).
X(x1)
Security Wire
Kit
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

4 5
STEP 2
Attach TV plate (A) to support column (D) at desired height using bolts (G) and metal washers (H).
Attach wire clips (J) to back of support column (D).
Optional: TV plate (A) can be installed on wall. Wall mounting hardware not included.
STEP 4
STEP 3
Mount monitor brackets (B) to the back of your TV using bolts (L, M, N, O, P, Q) and washers (R, S, T)
according to the size of mounting holes on your television. Make sure monitor brackets are both in the
correct orientation. For curved monitors, spacers (U, V) may be required.
Mount monitor to TV plate (A) as shown in diagram. Tighten safety bolts on bottom of monitor
brackets (B) using phillips head screwdriver.
Route cables through cable management clips (J) on back of stand.
safety bolt

6 7
STEP 5 STEP 5 (Continued)
5d
OPTION B: Concrete/Brick Wall
Drill 2” (50mm) deep holes using a 5/16” (or 8mm) drill bit, and press anchors into holes. Secure with
screws and washers.
5a
5c
OPTION A: Wood Wall
Drill 1.75” (45mm) deep holes using a 5/32” (or 3.8mm) drill bit. Secure with screws and washers.
5b
If your TV is located near a wall as shown in Diagram 5a, then a steel wire from security wire kit (X) can
be attached for added security. Attach the two ends of the steel wire to the top two holes on the back of
your TV as shown in Diagram 5b. Attach the center loop to your wall according to wall type as shown in
Diagram 5c, 5d, 5e.
5e

Last Updated: 10/17/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654