Vivo MOUNT-TVSG1 User manual

Wall Mount Designed for Samsung TV’s
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-tvsg1
SKU: MOUNT-TVSG1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
B(x1)
Right Wall Plate
M-A (x2)
M8x55mm Screw
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualied technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
M-C (x2)
M8x10mm Screw
M-B (x3)
M8x18mm Screw
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-9303.
A (x1)
Le Wall Plate
C(x1)
Le TV Plate
D(x1)
Right TV Plate
Pencil
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
132lbs
(60kg)
E(x1)
Kickstand
G(x4)
Square Pad
F (x2)
Protective Film
M-D (x2)
Spacer
H(x2)
Round Pad
I(x1)
Sticker
T-A (x1)
Measuring Tape
W-A (x8)
ST5.5x55mm
Screw
W-B (x8)
Anchor
Level Studfinder

3
Stud / Wood Wall Installation
Secure Measuring Tape (T-A) to the wall in
the desired location using Stickers (I). Align
the marks on Measuring Tape (T-A) with
the outside of the tabs on Le Wall Plate
(A) and Right Wall Plate (B). Mark drilling
locations. Use of a stud nder and level is
recommended.
Pre-drill the marked location. For drywall,
use an 8mm (5/16”) drill bit, and drill
appoximately 60mm (2.4”). For studs, use a
4mm (5/32”) drill bit, and drill approximately
55mm (2.2”) deep.
Insert Anchors (W-B) and mount wall plates
using ST5.5x55mm Screws (W-A) and a
Phillips screwdriver.
ASSEMBLY STEPS
STEP 1
Find the center of your TV using Measuring Tape (T-A). Mark the distance of your TV’s top VESA
mounting holes on Measuring Tape (T-A). If the VESA holes are 1000mm (39.4”) or greater, swap Le
Wall Plate (A) and Right Wall Plate (B), and use the orientation through the remainder of the manual.
STEP 2 (Option A)
a = Distance between VESA holes
b = Height of TV
c = 1/2 of a
d = Center of TV
B
A
B A
T-A
T-A
B
A
W-B
W-A
Tab
Note: The brackets are showing the setup
for a 800mm or less VESA pattern.
T-A
I

4
STEP 2 (Option B)
For AU8000-AU9000, Q60A-70A, QN85A-QN95A, QN800A, QN900A, Q800A, Q900A
Remove the adhesive backing from Protective Film (F) and place them over the top VESA holes on the
TV, making sure the arrows are facing inward.
Concrete/Brick Wall Installation
Secure Measuring Tape (T-A) to the wall in the desired location using Stickers (I). Align the marks on
Measuring Tape (T-A) with the outside of the tabs on Le Wall Plate (A) and Right Wall Plate (B). Mark
drilling locations. Pre-drill the marked locations, and use an 8mm (5/16”) drill bit drilling appoximately
60mm (2.4”) deep. Insert Anchors (W-B) and mount wall plates using ST5.5x55mm Screws (W-A) and a
Phillips screwdriver.
STEP 3 (Option A)
F
Tab
A
B
W-B
W-A
Note: The brackets are showing the setup for a
800mm or less VESA pattern.
I
T-A

5
STEP 3 (Option A Continued)
For AU8000-AU9000, Q60A-70A, QN85A-QN95A, QN800A, QN900A, Q800A, Q900A
Assemble Le TV Plate (C) and Right TV Plate (D) to the TV using Spacers (M-D) and Screws (M-A
through M-C). Snap in Spacers (M-D) between the tabs on TV Plates (C,D) with the raised side facing
down. Remove adhesive backing from Square Pads (G) and place them on the back of the TV. Mount
Kickstand (E) to one of the lower VESA holes using M8x18mm Screw (M-B) to access the TV ports.
STEP 3 (Option B)
C
D
M-D
M-A
M-B
M-C
E
G
M-B
Other Models and Mounting with One Connect Box
Assemble Le TV Plate (C) and Right TV Plate (D) to the TV using Spacers (M-D)
and Screws (M-A through M-C) and the spacers provided with your TV. Remove
the adhesive backing from Round Pads (H) and place them at the
bottom of the TV with the spacers provided with your TV. Install
the One Connect Box using the hardware
provided with the TV.
C
D
M-D
M-A/M-B/M-C
H

6
STEP 4
Hang Le TV Plate (C) and Right TV Plate (D) over Le Wall Plate (A) and Right Wall Plate (B).
Pull down on TV to lock TV Plates (C,D) into Wall Plates (A,B).
B
A
C
D

7
STEP 5
To remove the TV, li up on one side rst to unlock one plate, then li on and unlock the other side.
Li the TV up and out of the mount.

LAST UPDATED: 04/07/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303