Vivo STAND-TV03E User manual

Mobile TV Cart
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv03e
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-TV03E

2 3
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Attach wheels (9) to the long and short square
tubing (1,2) using the provided wrench (15).
STEP 2
Attach the square tubing (1,2) to the tube
connector (3) using M6x60 Allen head bolt
(11) and the M6 socket plate (12).
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
turn this nut to adjust
the height of the wheel
PACKAGE CONTENTS
1 (x2)
Long Square
Tube
2(x2)
Short Square
Tube
3(x1)
Tube
Connector
9 (x4)
Wheel
10 (x2)
Square Plate
Connector and
Rubber Pad
11 (x8)
M6x60
12 (x4)
M6 Socket
Plate
8(x4)
Pole Cover
4 (x1)
Tube Connector
Cover
5 (x2)
Pole with
Holes
6 (x2)
Pole without
Holes
7 (x2)
Pole
Connector
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
14 (x2)
M5x6 Grub
Screw
13 (x14)
M6x10
15 (x1)
Tool Kit
22 (x4)
M6x20
M6x35
23 (x4)
M8x20
M8x35
M8x45
21 (x4)
M4x12
M4x30
17 (x2)
Shelf Support
18 (x4)
M4x6
20 (x1)
TV Arm Set
24 (x4)
M4 Washer
19 (x1)
Square
Plate
25 (x12)
M6 Washer
26 (x4)
M8 Washer
27 (x4)
M4 Spacer
M6/8 Spacer
(20mm)
28 (x8)
M6/8 Spacer
(5mm)
16 (x1)
Shelf
9
1
2
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
11
3
12 1
2
Front
Bac k
Hole for Part 13
110 lbs
(49.9 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 10 lbs
(4.54 kg)
CART SHELF

4 5
STEP 3
Attach the base poles (5) to the tube connector (3) using M6x10 bolts (13) in the back and M5x6 grub
screws (14) in the sides. Thread on the pole connectors (7) to the tops of each base pole (5). Use
caution when threading pole connectors. Threads are very ne and may have sharp edges.
STEP 4
4a: Slide the tube connector cover (4) over the
base poles (5) and t over the tube connector (3).
4b: Thread the top poles (6) to the pole connectors
(7) and insert the pole covers (8) into the top.
STEP 5
5a: Slide the square plate connectors and rubber
pads (10) over the top of the poles (6) and
tighten the grub screw using tool kit (15).
5b: Attach the square plate (19) to the square plate
connectors (10) with 8 6x10 Allen head bolts (13)
and 8 M6 washers (25) using tool kit (15).
STEP 6
6a: Clip bubble level from tool kit (15) onto the
square plate (19). Adjust the level of the square
plate (19) by loosening the grub screw in the
back of the square plate connector (10) using
tool kit (15). Tighten grub screws again once
you’ve reached desired height and level.
6b: Secure TV arm set (20) to the back of your
television using bolts (21-23) and washers (24-26),
depending on the size of the mounting holes on
the television. For curved or recessed TVs, a spacer
may be required (27,28).
5
7
13
4
Remove plastic sleeves
before attaching the par t 4
6
8
10
10
15
Attach bubble level
to the w al l plate
15

6 7
STEP 7 STEP 9
Attach the TV arm set (20) to the square plate (19). Tighten the safety bolts on the bottom of the TV
arm set (20) to secure the television to the stand.
To attach the shelf (16), rst attach the shelf supports (17) to the bottom poles (5) using 4 M6x10 Allen
head bolts (13). Once secured, attach the shelf (16) to the supports (17) using 4 M4x6 countersink
bolts (18).
STEP 8
8a: If additional leveling and height adjustment
is required aer television is attached, repeat
step 6.
8b: For wire management, cables can be run
through the tops of the pole covers (8) and down
through the poles.
OPTION A
OPTION B
16
18
13 17
14

Last Updated: 1/9/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654