vollara FRESH AIR MOBILE User manual

MOBILE
ANYWHERE, EVERYWHERE
Portable Electronic Purier
CAUTION: READ MANUAL CAREFULLY FOR PROPER PROCEDURES AND OPERATION.

2
Specifications ........................... 2
Control Pad Layout ...................... 2
Operation............................... 3
Mounting the Base....................... 3
Adjusting the Wire Stand ................. 4
Wire Stand Positions ..................... 4
Power Adapters ......................... 5
12VDC Adapter Fuse ..................... 5
Portability............................... 5
Disassembly ............................ 6
Yearly Maintenance ...................... 6
Cleaning ................................ 7
Troubleshooting ......................... 7
• 12VDC or 110 - 240 VAC 50/60Hz
• Operating Temperature:
45˚F - 100˚F (7˚C - 38˚C)
• Maximum 10.7 watts
• Fixed 8.5 KV DC needle ion generator
• 3 speed fan
• Fuse (12VDC adapter only):
2 amp Buss type
• Size: 3.625” x 6” x 1.0”
9.21cm x 15.25cm x 2.54cm w/o base
• Weight: 8 ounces (.23kg)
CAUTION! - Use O3Boost in
accordance with directions found
in this manual only.
CAUTION! - Disconnect power
cord before servicing.
WARNING! - UV Lamp operation.
Do not operate this unit unless the
case is completely and correctly
assembled. Failure to comply may
result in serious eye damage.
PURIFIER
O
3
BOOST
CONTENT SPECIFICATIONS
CONTROL PAD LAYOUT
Vollara, LLC • 300 East Valley Drive • Bristol, VA 24201 • 800.989.2299 • www.Vollara.com
Please record the name and phone number of your
Vollara Independent Business Owner:
Name:
Phone:
Please record the serial number of your FreshAir Mobile:
Serial #:
Did you forget to register
your FreshAir Mobile?
By registering, you’ll activate
your warranty. Your privacy is
guaranteed. Just fill out your
warranty card and drop it in
the mail.
LOW LOWHIGH HIGH
MED MED

3
PARTS AND ACCESSORIES
A. WIRE STAND ........................................................................9950153
B. BASE ...............................................................................9950154
C. KNOB/CLAMP PACK (2) ..............................................................9950155
D. 12VDC ADAPTER ....................................................................9950157
E. 2.0 AMP FUSE .......................................................................9950162
F. AC ADAPTER ........................................................................9950158
C
C
C
C
A
B
D
E
A. WIRE STAND 9950153
B. BASE 9950154
C. KNOB/CLAMP PACK (2) 9950155
D. 12VDC ADAPTER 9950157
E. 2.0 AMP FUSE 9950162
F. AC ADAPTER 9950158
Fuse for 12VDC Adapter only
L
O
C
K
O
P
E
N
L
O
C
K
O
P
E
N
PUSH
F
ORDER PART# 9950159
FRESH AIR MOBILE SERVICE KIT
ACTIVEPURE
®
TARGET
TARGET FRAME
Red Wires
UV BULB
ACTIVEPURE
®
PLATE
C
C
C
C
A
B
D
E
A. WIRE STAND 9950153
B. BASE 9950154
C. KNOB/CLAMP PACK (2) 9950155
D. 12VDC ADAPTER 9950157
E. 2.0 AMP FUSE 9950162
F. AC ADAPTER 9950158
Fuse for 12VDC Adapter only
L
O
C
K
O
P
E
N
L
O
C
K
O
P
E
N
PUSH
F
TARGET FRAME
ACTIVEPURE
®
TARGET
UV BULB
ORDER PART# 9950209
FRESH AIR MOBILE SERVICE KIT

4
LEDs
• Peel and stick one
part of the Velcro to
the base, then attach
the other to a clean,
dry surface, or...
• Attach suction cups
by pressing and
twisting into the
base, or...
• Screws may be used
for extra security
and where the other
methods are not
appropriate.
Setting Coverage
 Low: Compact Car, Pickup
Med: Large Sedan, SUV, or Semi-Cab
High: RV/Motor Home or Houseboat
 OFF: Purifier o: ionization & fan may continue operating if desired.
OPERATION
1. If desired, mount the base in an appropriate location (see below).
2. Adjust the wire stand (see page 5).
3. Plug in either the 12VDC car adapter or the AC adapter.
4. The FreshAir Mobile unit will come on when power is supplied to the unit.
5. Adjust the Purifier by pressing the Purifier UP and Purifier DOWN buttons. When the unit is off,
all the LED lights will also be off.
6. Set the O3Boost by pressing the O3Boost UP and O3Boost DOWN buttons. See the Settings
chart (below) for proper adjustments. When the O3Boost is set to off, the LEDs will also be off;
the Purifier LED(s) will remain on. DO NOT EXCEED RECOMMENDED SETTINGS.
MOUNTING THE BASE
The base for the FreshAir Mobile can be mounted using the included suction cups, Velcro, or
screws, depending on preference. When using suction cups or Velcro, be sure the surface is
smooth and clean. Dirt, grease, protectants, and other substances will affect performance and
holding ability.

5
• Sitting on a flat
surface with or
without the base
• Hanging over an
edge pointing down
(laundry hamper,
garbage can, etc.)
• Sitting on a flat surface
without the base
• On a vertical surface
with the base (wall
mount, window, etc.)
• Hanging over an edge
pointing up (seat pocket
in car)
ADJUSTING THE WIRE STAND
The wire stand on the FreshAir Mobile allows for quick release from the base, provides a stand or
hanger for the unit independent of the base, and allows the unit to either stand or hang from the
base depending on how the base is mounted.
To adjust the wire stand, loosen the two knobs on the sides of the unit approximately 1/2 turn. The
unit may then be tilted up or down to adjust the angle or moved on the wire stand to change the
height. You can also remove and change the position of the wire stand to accommodate several
different mounting methods. To reinstall, simply align the two clamp collars and insert the wire
stand. Once the unit is adjusted, tighten both knobs to hold it in place.
WIRE STAND POSITIONS
ORTHEN
NOTE: Unit can be used without attaching the base or wire stand.
EFFECTS OF HIGH OR LOW VOLTAGES ON FRESHAIR MOBILE™
WHEN USING THE 12VDC CAR ADAPTER
FreshAir Mobile™ has an operating voltage range of 11 VDC to 14.6 VDC. If the voltage coming
into the unit is too high, the unit may blow the 12VDC adapter fuse. This type of problem usually
indicates something is wrong with a vehicle’s electrical system. If the unit shuts down while using
the 12VDC automotive adapter and you are unsure of the cause, check the adapter fuse. If the fuse
is not blown, test the unit using the supplied AC adapter. Once the voltage problem (drained car
battery, electrical system problem, etc.) is corrected by a qualified service person, you will be able
to resume using your FreshAir Mobile™ with the 12VDC adapter.

6
• Insert the car adapter
into an appropriate
12 volt automotive
type power outlet.
• Insert the small adapter plug into the opening located underneath
at the rear of the unit.
• Select and install the proper
international plug into the AC adapter.
Insert correctly assembled adapter
into a standard electrical outlet.
THEN
NOTE: when installing one of the
interchangeable plugs, be sure to twist
and lock it into place. When removing
a plug, press the raised tab to release,
then turn the plug out the top.
PUSH
L
O
C
K
O
P
E
N
L
O
C
K
O
P
E
N
PRESS HERE
• To remove the unit from
an attached base, press
down on the front latch
and slide the unit back,
then up.
NOTE: If you prefer to remove the base and unit together, mount the base with Velcro or
suction cups to a clean, dry surface.
• Once the unit is assembled
and the base mounted,
simply snap the wire stand
into the base. The latch at
the front of the base should
snap into place, locking in
the stand and unit.
PRESSSLIDE THEN LIFT
• For added convenience,
mount extra bases where
you use your FreshAir
Mobile most. See your
Vollara Independent
Business Owner for more
information.
POWER ADAPTERS
FreshAir Mobile comes with both a 12 volt DC car adapter and a 100 - 240 volt 50/60 Hz AC
adapter with interchangeable plugs.
PORTABILITY
Depending on how it is mounted, your FreshAir Mobile can be ready to take with you in just a few
seconds.
To change the car adapter fuse, unscrew and remove the front
of the adapter. Replace with the same type and rating only:
2 amp Buss type fuse (service part #9950162).
OR
12VDC Adapter Fuse
CAUTION: Not for use on 12 volt positive ground or 24 volt
vehicles. Doing so may damage the product.

7
1. Turn unit over, tilt up slightly,
and remove screws at the
front of the unit.
2. With the front remaining tilted
up, slide the lower half of the
case back and up until it is free.
3. Lift the small circuit board holding
the target screen and bulb (Bulb
Assembly) from the two tabs.
4. Disconnect the leads of the
Bulb Assembly from the
main circuit board.
All user maintainable parts
of the FreshAir Mobile are
accessed by removing the
lower half of the case.
DISASSEMBLY (FOR MAINTENANCE AND REPLACEMENT OF SERVICE KIT 9950209)
CAUTION: The unit must be disconnected from its power
source before servicing, and should not have
the power reconnected unless the case is
correctly and completely reassembled.

8
Reinstallation is the reverse of the above steps:
• UV lamp – Do not touch with bare hands.
If touched, clean the bulb with a cotton swab
and a small amount of alcohol.
• Attach ActivePure® Target Screen (a) to
the Target Frames (b).
• Install the legs of the Target Frames (b) into
the four holes of the Bulb Assembly
PC board (c).
• Attach the 3‐pin connector (e) of the Bulb
Assembly to the main unit PC board.
• Carefully align the two holes in the Bulb
Assembly to the two tabs on the
main unit.
• Press gently to install the Bulb Assembly.
• Carefully replace the bottom case, being
sure the pins inside the back of the bottom
case fit into the two standoffs at back of the
top case. Slide the bottom case forward
then down, making sure the wires are
completely inside the case.
• Check for proper alignment before installing
and tightening the screws. Failure to correctly
assemble may cause damage to the case.
• Replace cover and two screws.
5. Remove the Bulb Assembly from the unit.
YEARLY MAINTENANCE
A service kit is available for your FreshAir Mobile. The kit contains a new ActivePure® Target,
UV bulb, and ActivePure® Purification Plate. For optimum performance, Vollara recommends
replacing these components annually. See your Vollara Independent Business Owner for
more information.
DISASSEMBLY - CONTINUED
ASSEMBLY
a
b
c
d
Tabs

9
CLEANING
Depending on conditions, your FreshAir Mobile will require periodic cleaning of certain
internal components every one to three months.
ActivePure® Target - Clean the target by gently removing dust with a small, soft brush.
UV Bulb - The UV bulb should be gently wiped with a soft, dry cloth.Avoid handling the UV bulb more
than necessary.
ActivePure® Ozone Plate - The top area of the ActivePure® Purification Plate can be cleaned
with ammonia or alcohol and a cotton swab. Do not use water. Allow to dry thoroughly.
Case - Clean the exterior case of your FreshAir Mobile with a soft cloth dampened (not wet)
with water. Do not use harsh chemicals or solvents.
Fan/Interior of unit - The interior and fan may be cleared of dust using canned air suitable
for electronics.
TROUBLESHOOTING
If your unit fails to operate properly after performing troubleshooting, contact your Vollara
Independent Business Owner for further assistance. You may also contact Vollara at
800.989.2299, or visit www.Vollara.com for additional support.
WARNING: Under no circumstances should
your FreshAir Mobile unit be operated while
any part of the case is damaged, missing, or
disassembled. If the case is damaged, return
your unit to Vollara for repair or replacement.
Direct exposure to the internal UV light may
cause eye damage.
Unit does not operate/the O3Boost does not
operate/all LEDs off
• Unplug and reinsert the adapter plug and
adapter to check where the power supply is
plugged in to be sure it has power.
• If using the 12VDC car adapter, remove the
fuse by unscrewing the end of the adapter
and check to see if it is blown. Replace it
with the same type and rating fuse only (see
Specifications). If the fuse is not blown, check
the outlet for proper voltage.
UV bulb or O
3
Boost may not be working
• Press the PURIFIER UP or PURIFIER DOWN
buttons to turn the Purifier function ON.
• If checking O3Boost operation, press the
O3Boost UP button to turn the O3Boost ON.
• Remove the Bulb Assembly, clean, and reinstall
(see Disassembly and Cleaning).
• If cleaning and reinstalling does not correct
the problem, replace the Bulb Assembly
(service kit #9950209).
• When looking through the rear inlet vents in
low light you should see a slight bluish glow.
If there is no glow, replace the Bulb Assembly
(service kit #9950209).
Lack of air flow
• Make sure the intake vents are not blocked
and the front of the unit is clear.
• Check to see if the fan is operating (if not,
see above).
NOTE: See page 8 for detail views of components.

LIMITED 1 YEAR WARRANTY
WHAT IS COVERED BY THIS WARRANTY
We warrant the FreshAir Mobile to the consumer, subject
to the conditions below, against defects in workmanship
or material, provided that the products are returned to a
service location within the following time periods:
• FreshAir Mobile within one (1) year of date of purchase.
INSTALLATION AND MAINTENANCE
REQUIREMENTS
This warranty is expressly conditioned upon proper
installation, operation, cleaning and maintenance, all in
accordance with the User’s Manual. Failure to meet any
of these requirements will void this warranty. Servicing of
your FreshAir Mobile by parties other than our authorized
representative and/or using parts other than genuine
parts will also void this warranty.
HOW TO OBTAIN WARRANTY SERVICE
Customer must contact Vollara Customer Service or
their Independent Business Owner and provide proof of
purchase within the above time period. We will repair or
replace and return the product, without charge and within
a reasonable period of time, subject to the conditions in
the above paragraphs, if its examination shall disclose
any part to be defective in workmanship or material. If we,
in our discretion, are unable to repair the product after a
reasonable number of attempts, we will provide either a
refund of the purchase price or a replacement unit, at the
company’s option.
WHAT IS NOT COVERED BY THIS WARRANTY
This product is intended for household use only. Ordinary
wear and tear shall not be considered a defect in
workmanship or material. These warranties do not apply
to filters nor for loss or damage caused by accident,
fire, abuse, misuse, improper installation, modification,
misapplication, commercial use, or by any repairs other
than those provided by our authorized Service Center.
MISSING SERIAL NUMBERS AND
UNAUTHORIZED CHANNELS
If a valid serial number is missing from the product, the
warranty will be voided. Vollara products are authorized for
sale through Vollara Independent Business Owners only.
Warranties are voided if a product is purchased through
unauthorized channels, this includes websites that are not
authorized to use Vollara’s trademarked names, images
and logos as well as Internet auction sites (e.g. ebay
and Craigslist). The only approved Internet presence for
Vollara products is www.vollara.com. To confirm warranty
coverage prior to purchasing a product, contact Vollara at
800.989.2299 with the serial number located on the back
of the unit.
EXCLUSION OF OTHER WARRANTIES
AND CONDITIONS
EXCEPT AS PROVIDED HEREIN, WE MAKE NO
REPRESENTATION OR WARRANTY OF ANY KIND.
ALL OTHER WARRANTIES OF ANY KIND, EXPRESS
OR IMPLIED, ARE HEREBY EXPRESSLY DISCLAIMED,
INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
LIMITATION OF LIABILITY FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES
WE SHALL NOT IN ANY CASE BE LIABLE FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING FROM BREACH OF EXPRESSED OR IMPLIED
WARRANTIES, CONDITIONS, GUARANTEES OR
REPRESENTATIONS, BREACH OF CONTRACT,
NEGLIGENCE OR ANY OTHER LEGAL THEORY. Such
excluded damages include, but are not limited to, loss of
profits or revenue, and loss of the use of the products.
FOR U.S. APPLICATION ONLY
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Some states do not allow limitations on warranties, or on
remedies for breach. In such states, the above limitations
may not apply to you.
This warranty is provided by
Vollara, LLC
300 East Valley Drive
Bristol, VA 24201.
SERVICE
Every eort is made to ensure customers receive an up-
to-date instructions manual on the use of our products;
however, from time to time, modifications to our products
may without notice make the information contained herein
subject to alteration. For the latest information, please visit
our web site.

This equipment has been tested and found to
comply with the limits for Industrial, Scientific, and
Medical Equipment (ISM), pursuant to Part 18 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television, which can be determined
by turning the equipment o and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a
circuit dierent from that to which the receiver is
connected
• Consult the Dealer or an experienced radio/TV
technician for help
FCC DECLARATION OF CONFORMITY
Name: FreshAir Mobile Model: A1018B
Manufacturer: Vollara
This device complies with Part 18 of the
FCC Rules.
RESPONSIBLE PARTY
Vollara, LLC
300 East Valley Drive
Bristol, VA 24201
Ph: [phone]
Signature: __________________________________
Printed Name: Andy Eide
Title: Vice President, Product Development
and Research
Date: 3/01/2018
FAM_OM_65-00657_VA-01013_0318
65-00657 VA-01013
© 2018 Vollara, LLC. All Rights Reserved.