Volt VDL-6008-4-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT®Florentine Deck Light
VDL-6008-4-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Florentine Deck Light
VDL-6008-4-BBZ
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be connected to a low voltage 12 volt
transformer.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that are
suitable for outdoor use.
WARNING: LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
!
www.voltlighting.com
- 2 -

Package Contents
Product Dimensions
A. (1) Fixture Body
B. (1) Lamp
[email protected] • 813.978.3700
4.25” 2.75”
C. (2) Lock Screw
3.5”
- 3 -
ProTip for Hiding Splice Connections
ProTip for Hiding Lead Wire
2”
Determine the location for the xture. Drill a hole straight through the
desired mounting location and run the lead wire out the backside of
the location so that the wires are not visible from the front side. Use a
matching trim piece and cut a groove in the back of trim. Cover the lead
wires with the matching trim piece.
All xtures come with 4’ of lead wire enabling you to hide the splice
connections out of sight. If you must make a splice connection in view, use
an inline heat shrink style connection that is less visible than traditional
twist caps.

www.voltlighting.com
INSTALLATION INSTRUCTIONS
Remove Face Cover
1
Face Cover
Fixture Body
Rotate
Install Lamp
3
Insert lamp with the correct
wattage and type marked on
xture label and push into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Lamp
Socket
- 4 -
Install Fixture Body
2
Fixture Body
Lock Screw
Wall Anchor
(optional)
Hole
VOLT®Florentine Deck Light
VDL-6008-4-BBZ
Rotate the face cover until it
stops and then lift the cover
straight o.
Note: The rst time it may be
dicult because the xture
has a very tight o-ring seal and
a grease sealant for moisture
protection.
Attach the xture body to your
desired location and secure with lock
screws.
Note: Wall anchors may be required
for certain installation conditions
(e.g. Brick walls, Concrete Walls,
etc.). Mark on the wall using holes
on the xture body to drill holes for
your wall anchors. Remove base and
drill proper holes in the wall, then
insert wall anchors.

[email protected] • 813.978.3700
Install Face Cover
4
Fixture Body
- 5 -
Face Cover
Wire Connections
5
Fixture
Wire
Connectors
Main Supply Cable
Pigtail
Install/Replace Lamp
Rotate the face cover and remove it to expose the lamp. Replace it with the
correct wattage and type marked on the xture label. Then, reinstall the
face cover.
IMPORTANT: Halogen bulbs must be protected from moisture and dust at all
times. Always reinstall the face cover when removed.
Push face cover back onto the
xture body aligned with the gaps
in the xture body. Once the face
cover is ush with the xture body,
rotate the face cover until it stops
and locks into place.
Strip both leads from luminaire
pigtail. Using two wire connectors
(sold separately), connect leads
from luminaire to main supply cable
leads.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
Attach the decorative arms on the
top or bottom of the xture body
and secure with lock screws. Multiple
decorative arms can be added going
up or down to create your own unique
look.
Note: Wall anchors may be required
for certain installation conditions (e.g.
Brick walls, Concrete Walls, etc.).
Mark on the wall using holes on the
xture body to drill holes for your wall
anchors. Remove base and drill proper
holes in the wall, then insert wall
anchors.
Install Decorative Arms
Fixture
Body
Decorative Arms
Decorative arms are sold as
additional options for this deck light.
Please read the following steps for
installation of the decorative arms.
5.5”
3.5”
Decorative
Arms
Decorative
Arms
Hole
Hole
Decorative
Arms
Lock Screw
Wall Anchor
(optional) Hole
VOLT®Florentine Deck Light
VDL-6008-4-BBZ

[email protected] • 813.978.3700
- 7 -

IS-VDL-6008-4-BBZ.ver3.pdf
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -