Volt Top Dog Scotty Mini Twinnovator Brass User manual

VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
V O LT ® Top Dog Scotty Mini Twinnovator Brass Path & Area Light
ITEM: VPL-3398
INSTALLATION INSTRUCTIONS
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

V O LT ®Top Dog Scotty Mini Twinnovator Brass Path & Area Light - VPL-3398
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3 meters]
of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that are
suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
813.978.3700 • [email protected] • www.voltlighting.com
2

PACKAGE CONTENTS
PRODUCT DIMENSIONS
INSTALL STAKE
1
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on top
of the stake while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
813.978.3700 • [email protected] • www.voltlighting.com
3
PACKAGE CONTENTS
A. (1) Fixture
A. (2) MR11 Lamps
5.7”
2.25”
25.25”
6.25”
4”
14”

REMOVE GLARE GUARD AND LENS
2
INSTALL LAMP
3
V O LT ®Top Dog Scotty Mini Twinnovator Brass Path & Area Light - VPL-3398
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Loosen the set screws and remove
the glare guards from the lens. Then
remove the lens from the xture.
Fixture
Set Screw
Glare Guard
Lens
Insert lamp with correct wattage and
type marked on xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
Socket
Lamp
INSTALL LENS AND GLARE GUARD
4
Place the lens over lamps and thread
onto xture. Attach glare guards back
onto the lens and secure with set
screws.
Fixture
Set Screw
Glare Guard
Lens

INSTALL FIXTURE TO STAKE
5
WIRE CONNECTIONS
6
813.978.3700 • [email protected] • www.voltlighting.com
5
Clear away area in ground at wireway
slot in top of stake. Align the wireway
slots on base and stake. Lay luminaire
pigtail into wireway slots and screw
xture into stake. Tighten until snug to
secure base.
Fixture
Wireway Slot
Pigtail
Stake
Strip two leads from luminaire pigtail. Using two wire connectors (not
provided), connect leads from luminaire to main supply cable leads.
Pigtail
Wire Connectors
Main Supply Cable

ADJUST ANGLE OF LAMP
7
V O LT ®Top Dog Scotty Mini Twinnovator Brass Path & Area Light - VPL-3398
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
6
By using screwdrivers, loosen
adjustment screws and adjust lamps
to your desired angles and then tighten
adjustment screws.
Adjustment
Screws
INSTALL REPLACE LAMP
Unscrew screws on glare guards and remove glare guards and shields to
expose the lamp and replace it with correct wattage and type marked on
xture label. And then reinstall shields and glare guards and tighten with
screws.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always re-install shields and glare guards when moved.

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
6