VQ Models VQA128 User manual

SPORT
60
60 Class - 2 Cycle engine
90 Class - 4 Cycle engine
Radio control model - RC Flugmodell
SPECIFICATIONS
Wingspan 67.3 in.
Length 51.1 in.
Electric Motor 1000 Watt (BOOST 90)
Glow Engine 60 2-T / 90cc 4-T
Radio 5 Channel / 5 Servos
TECHNISCHE DATEN
Spannweiter 1710mm
Lange 1030mm
Elektroantrieb 1000 Watt (BOOST 90)
Verbrennerantrieb 60 2-T / 90 4-T
Fernsteuerung 5 Kanal / 5 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
INSTRUCTION MANUAL / Montageanleitung
Or electric equivalent

1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
The pre-covered film on ARF kit may wrinkle due to variations
of temperature. Smooth out as explained right.
* Use an iron or heat gun. Start as low setting. Increase the
setting if necsessary. If it is too high, you may damage the
film Low setting
SILICON
EPOXY A
EPOXY B
CA
GLUE
Epoxy Glue ( 5 minute type)
Silicon sealer
Cyanoacrylate
Glue
Minimum 5 channel radio
for airplane with 5 servos
.90 - 4 cycle
Silicone tube
Extension for aileron
servo.
.60 - 2 cycle
REQUIRED FOR OPERATION (Purchase separately)
Epoxy Glue (30 minute type)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
.Motor control x1 .Aileron x2
.Elevator x1 .Rudder x1
1000w
Brushless Motor
70A Regler
Li-Po Battery, 22.2V, 5300mAH
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”

* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.
Cut away only the
covering
IN CASE OF NOSE GEAR USING
3x15mm screw
4x45mm screw
4mm bolt
4mm washer
75mm wheel
Aluminum landing gear
1- Landing gear
...4
3x15mm screw

IN CASE OF TAIL GEAR USING
1-Securely attach the nose gear mount to the fire-wall using the four 3x15mm screws
2-Insert the white plastic tube into the fuselage, through the firewall.
3-Insert the Z-bend of the nose gear control push-rod into the hole on the nose gear control horn.
4-Insert the pus-hrod into the plastic tube
5-Position the nose gear control horn on the center of the nose gear mount.
6-With the screw hole facing forward, slide the straight end of the nose gear on to the nose gear mount.
7-When satisfied with the fit and alignment, secure the nose gear control horn in place with 1/8x13/32”(3x10mm) set screw.
...4
3x15mm screw
2- Nose gear
3- Landing gear
65mm wheel
...4
3x15mm screw
* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.

Remove the magnetic top hatch from
the fuselage
4- Engine
4x30mm screw
3x25mm screw
..............4
3x25mm screw
...4
4x30mm screw
5x80mm.......4
5mm nut.......12
5mm washer...16
5- Electric Motor

Remove the covering material from over both the foot of the
vertical stabilizer hole.
Pull the left and right elevator out of the
horizontal stabilizer.
Cut away only
the covering
6- Electric Motor
7- Horizontal stabilizer

* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.
Using the pencil trace around the top and bottom
of the stabilizer where it meets the fuselage.
Remove the horizontal stabilizer from the fuse-
lage. Remove the covering material from the gluing
surfaces on both the top and bottom of the horizontal
stabilizer.
NOTE: Do not glue the horizontal stabilizer into the
fuselage at this time.
Trial fit the horizontal stabilizer in place on the
fuselage. Check the alignment of the horizontal
stabilizer by measuring from a fixed point along
the center line of the fuselage to the leading edge
on each side of the horizontal stabilizer. The
distance must be equal on both sides.
Again, slide the horizontal stabilizer into the
fuselage. Check the alignment of the horizontal
stabilizer. Secure the horizontal stabilizer in place
using the thin CA glue.
Cut away only
the covering
both sides
CA
CA
Glue both the
top and bottom
Glue inside the slot
Securely glue together. If coming off during flight,
you lose control of your air plane.
8- Horizontal stabilizer
NOTE: cut inside the pencil lines.

Attach the Vertical Stabilizer and the Horizontal Stabilizer
Incorrect
Correct Incorrect
A
A=A’ A=A’
/B=B’
/
Check the alignment of the horizontal stabilizer by measuring from a fixed point along the center line of the fuselage to the leading
edge on each side of the horizontal stabilizer. The distance must be equal on both sides. If not, adjust the stabilizer until the
measurements are the same.
BB’
B=B’
BB’
A’
BB’
B=B’
Using the pencil trace around the right and left
of the stabilizer where it meets the fuselage.
Remove the vertical stabilizer from the fuselage.
Remove the covering material from the gluing
surfaces on both the left and right of the vertical
stabilizer.
Full the rudder out of
the vertical stabilizer.
Trial fit the vertical stabilizer in place on the
fuselage. Check the alignment of the vertical
stabilizer.
Again, put the vertical stabilizer in place on the
fuselage. Check the alignment of the vertical
stabilizer. Secure the vertical stabilizer in place
using the thin CA glue.
* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.
Cut away only
the covering both sides
CA
Securely glue together. If coming off during flight,
you lose control of your air plane.
9- Vertical stabilizer
NOTE: cut inside the pencil lines.

Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Securely glue together. If coming off during flight,
you lose control of your air plane.
10- Rudder and Elevator
Control horn
...........1
Cut away only
the covering

2.2mm collar.....1
Vis 3x12mm......2
Tail wheel..........1
Tail gear mount
...................1
WING BOTTOM-VIEW
Adhesive tape
Adhesive
tape
CA
7x20mm dowel
......................4
7x20mm dowel
CA
CA
3x12mm screw
Collar
Tail gear mount
Horn
Horn
Tail wheel mount
Fuselage
Rudder
Gear
Piece of fuel tube (not included)
Side view
2.mm
5/64”
Horn .................1
Note: The aileron extension cord
not include.
2mm
Control horn
......................2
2x30mm screw
................4
11- Control horn
12- Tail wheel
13- Wing
Cut away only
the covering
Control horn
...........2
CA
2x175mm throttle rod
......2
......2