VQ Models CESSNA 188 AGWAGON User manual

SEMI SCALE MODEL
60 Class
90 Class
2-cycle engine
4-cycle engine CESSNA 188
AGWAGON
SPECIFICATIONS
Wingspan 1920mm
Length 1300mm
Electric Motor 1000 Watt (BOOST 90)
Glow Engine .60 2-T / .90 4-T
Radio 6 Channel / 8 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweiter 1920mm
Lange 1300mm
Elektroantrieb 1000 Watt (BOOST 90)
Verbrennerantrieb 10cc 2-T / 15cc 4-T
Fernsteuerung 6 Kanal / 8 Servos
MONTAGEANLEITUNG
INSTRUCTION MANUAL
Or Electric equivalent

70mm Spinner
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
Minimum 6 channel radio
for airplane
.90 cu.in (8.5cc)
Extension cord
.60 cu.in. (7.5cc)
REQUIRED FOR OPERATION (Purchase separately)
Minimum 6 Kanal
Fernsteuerung
Servoverlangerungskabel
BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten)
Brushless Motor
PICHLER BOOST 90
Brushless ESC
Brushless Regler
Battery / Flugakku LEMONRC 5300-22.2V
Silikonkleber
Tool Required/ Erfoderliches Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”

AB
AB
AB
Cut away only the covering
Cut away only the covering
(Both the top and bottom)
(Both the left and right)
5 min.
(5 min.)
Hinge
Petroleum jelly
STABILIZER
ABApply 5 min.
Epoxy both the
top and bottom.
Trial fit the horizontal stabilizer in place on the
fuselage. Check the alignment of the horizontal
stabilizer by measuring from a fixed point along
the center line of the fuselage to the leading edge
on each side of the horizontal stabilizer. The
distance must be equal on both sides.
Using the pencil trace around the top and bottom
of the stabilizer where it meets the fuselage.
Remove the horizontal stabilizer from the fuselage
Remove the covering material from the
gluing surfaces on both the top and bottom of the
horizontal stabilizer.
Spread epoxy onto the top and bottom of the
horizontal stabilizer where it contacts the fuselage.
Trial fit the vertical stabilizer in place on the
fuselage. Check the alignment of the vertical
stabilizer.
Using the pencil trace around the right and left
of the stabilizer where it meets the fuselage.
Remove the vertical stabilizer from the fuselage.
Remove the covering material from the gluing
surfaces on both the right and left of the vertical
stabilizer.
Spread the epoxy on the vertical stabilizer where
it contacts the fuselage and to the bottom of the
stabilizer.
Insert the vertical fin into the fuselage, ensuring
that it is seated properly on the fuselage.
3- Elevator / Hohenruder
1- Horizontal Stabilizer / Hohenruder
2- Vertical Stabilizer / Hohenleiwerk
Scharnier Hohenlleiwerk
AB
Both the right
and left
Both the top and bottom

Drill a 3/32”(2.5mm) diameter hole in torque rod mounting slot,
marking sure that you drill the hole perpendicular to the leading
edge of the rudder.
Position each hole 38mm (+/- 1mm) out from the edge of the rudder.
38mm
Test-fit the torque rod into the rudder.
When satisfied with the fit and alignment, remove the torque rod.
Apply a thin layer of petroleum jelly to only the pivot point of the
torque rod bearing
Hinge the rudder to the vertical stabilizer, using 5 minute epoxy. Make sure
to apply a thin layer of epoxy to the left and right of both hinges and to the
inside the torque rod mounting slot and to the end of the torque rod itself.
2.5mm
Hinge / Scharnier
Petroleum jelly
STABILIZER
ABApply 5 min.
Epoxy both the
left and right.
5- Rudder / Hohenleiwerk
Tail wheel control arm
Tail wheel push-rod
1
1- Insert the tail wheel pushrod into the hole on the tail wheel control arm (as show).
2- Re-install the rudder torque rod and tail wheel mount in place.
3- Secure the tail wheel mount in place using four 3x12mm screws.
Secure the tail wheel control horn in place using a 1/8”(3mm) screw set, Ensure smooth non-binding movement.
1
2
1
AB
Test-fit the rudder torque
rod into the slot.
3
Rudder torque rod
NOTE: You may need to open up the slots so
that the torque rod bearing are not too difficult
to push in
3x12mm screw
...........4
4- Tail wheel leg / Spornradtrager

Note: All holes on the fuselage and bilnd-nuts
are pre-installed at factory.
6- Main landing gear / Fahrwerk
4x15mm screw
Aluminum landing gear
7- Wheel / Radl
8- Engine mount / Motortrager
4X15mm screw
...........6
4X30mm screw
......2
..............2
..............2
! Align the mark on both mounts
with the mark on the fuselage
4X25mm screw
......4
..............4
..............4
4.5mm
.............2
Aluminum Haupfahrwerk

Rudder servo
Throttle servo
Switch
Nylon pushrod guide
Nylon pushrod guider
Rudder and tail wheel pushrod
Elevator servo
Elevator servo
9- Engine / Motor
10- Servo installation
11- Linkage / Alenkungen
140-141mm
140 - 141mm
! Engine thrust on balk
head is already adjust
at factory
1.5
TOP-VIEW
.........2
2x20mm
.......4
TOP VIEW / Draufsicht
BOTTOM - VIEW / Unteransicht

FUEL TANK
RECEIVER BATTERY
2.5x10mm.....4
Attach the board or transparent plastic on the side of the fuselage with the adhesive tape as show.
Using a pencil or felt tipped pen trace around the engine head where it meet the cowl. Cut the opening the board or trans-
parent plastic for the engine head as marked above.
Remove the engine and insert the cowl on to the fuselage so the distance from the fire wall to the front of the cowl is
138 to 139mm.
Remove the cowl from the fuselage and carefully cut the opening for the engine head as marked above. Do the same way
with the hole for needle-valve and silencer.
Again. Insert the cowl on to the fuselage and secure it in place with five 2x5mm screws.
138mm
Ruler
12- Fuel tank / Kraftstofftank
13- Cowling / Motorhaube
SIDE-VIEW / Seitenansicht

BATTERY STAND
F3
F3
F2
F3A
FUEL TANK STAND
FUEL TANK
BATTERY STAND
LI-PO BATTERY
Magnetic Battery stopper
(3mm plywood)
IN CASE OF LI-PO BATTERY USING
Slide the battery stand throughout the slots
on the bottom of F3
One end of the battery stand touched the
rear of the fire-wall
IN CASE OF GLOW ENGINE USING
IN CASE OF ELECTRIC MOTOR USING
Slide the battery stand (P1) throughout the slots
on the bottom of F3 so that the end of the battery
stand touched the rear of the fire-wall.
Secure the battery stand in place using the
magnetic battery stopper (P4).
P1
Place the Li-po battery on to the battery stand
and secure it in place with the nylon cable tie.
Nylon cable tie
F3
F2
Fire-wall
14- Li-po battery / Li-po akku
SIDE-VIEW / Seitenansicht

Insert the 18x500mm aluminum
tube throughout the fuselage
(do not using glue)
L/R
2x10mm
screw
X
X
Flap servo hatch
(plywood)
Flap push rod exit
Aileron servo
Aileron
push rod
305mm
CA
1-Using the ABS shield as a template, trace around the
outside edge of the ABS air-scoop,and then remove it.
2-Using a sharp hobby knife, cut away the covering inside
the lines. Not to cut into the wood.
3-Apply the ABS shield in place and secure with CA glue.
Do the same way with another half wing.
Cut away the
covering only
WING - TOP VIEW
15- Servo
16- ABS Shield
17- Wing installation / Flachenbefestigung
BOTTOM - VIEW / Unteransicht

5x20mm screw
5mm washer
5mm blindnut
pre-installed
inside.
Wood dowel Wood dowell
CA
1- Test-fit the dowel into the hole.
2- Secure the dowel in place
using CA glue.
Do the same way with another
haft wing.
Secure the half wing in place
using 5x20mm screw.
Do the same way with another
half wing.
Lightly, push the half wing
to the side of fuselage.
CA
19- Cockpit
18- Wing installation / Flachenbefestigung
5X20mm screw
......2
..............2

CA
Black nylon tube
20- Cockpit
21- Canopy / Kabinenhaube
2x12mm screw
3x15mm screw
22- Cockpit installation
2x12mm screw
...........5
3X15mm screw
...........2

Fiberglass shield
23- Wing brace
24- Tail shield
3x15mm
..........2

3x10mm screw
12mm
35mm
80mm
ELEVATOR CONTROL RANGE RUDDER CONTROL RANGE
Adjust the travel of each control surface to the values
in the diagrams these values fit general flight capabilites.
Readjust according to your needs and flight level.
Position for
right diagram.
AILERON CONTROL RANGE
FLAP CONTROL RANGE
CG
40mm
Position for right diagram.
Position for right diagram.
NEVER FLY BEFORE CHECKING THE CG’S REQUIRED POSITION.
Carefully install the battery pack to ensure that they will not shift during flight.
Shift the location of the battery pack as needed to obtain the specification.
Position for
right diagram(CG)
25- Tail shield
26- Control surface & Balance
Schwerpunkt & Ruderausschlage
150 - 153mm
40mm
12mm
80mm
All details are subject to change without notice ! Technische Anderungen und Irrtumer vorbehalten !
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
3x10mm screw
...........4
2mm