VQ Models VQA090 User manual

DORNIER
Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 63 in.
Length 47.6 in.
Electric Motor (See next page)
Glow Engine .46 2Stroke / .52 4-Stroke
Radio 6 Channel / 6-7 Servos
WARNING!
ACHTUNG!
This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1620mm
Lange 1210mm
Elektroantrieb (siehe nächste Seite)
Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T
Fernsteuerung 6 Kanal / 6-7 Servos
PICHLER
ARF BY
DO-27
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
(.46-.52 class glow conversion optional)
(7,5 -8,5cc Glühzündermotor Einbau möglich)
VQ No: VQA090
VQ No: VQA091

.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
6 - channel radio
RECOMMENDED ACCESSORIES (Purchase separately)
6 - Kanal
Fernsteuerung
Egänzungskit Verbrenner
(Tank + Motorträger)
Best.Nr. C4165
Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)
Antrieb Standard:
Antrieb Tuning (Kraftvoller Kunstflug):
BOOST 40 Brushless Combo Set, Best.Nr. C2983
LiPo Battery RED POWER 3200-3S, Best.Nr. C3164
Luftschraube 12*6, Best.Nr. C1937
BOOST 60 Brushless Combo Set, Best.Nr. C3174
LiPO Akku RED POWER 4250-5S, Best.Nr. C4547
Luftschraube 13*8, Best.Nr. C2846
Silikonkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
1 x Servo S4020
(für Seitenruder)
Best.Nr. C1687
3 x Servo S4020
(für Höhen- und Querruder)
Best.Nr. C4995
2 X Servo DS3012
(Fur Landeklappen)
# C4995

Full the elevator out of the
horizontal stabilizer.
Cut away only
the film both side
1A
1B
1
When you are satisfied with the alignment,
use a pencil to trace around the top and
bottom of the stabilizer where it meets the
fuselage.
Cut away only
the covering
both side
BB’
B=B’
Aluminum wing joiner
Remove the horizontal stabilizer from the
fuselage. Using the sharp hobby knife,
carefully cut away the covering inside the
lines which were marked above.
* WARNING: When removing any covering
from the airframe, please ensure that you
secure the cut edge with CA or similar
cement. This will ensure the covering
remain tight.
Stabilizer
AA’
A=A’
Stabilizer
FUSELAGE
Again, Install the horizontal stabilizer into the
fuselage and adust the alignment as described
in steep 1C. Secure the horizontal stabilizer in
place using CA glue.
1C
1D
1E

Note: The slots for the control horn
installation are pre- cut at factory.
Control horn
...........2
CA
CA
Thin CA glue
Thin CA glue
Push the elevator and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer.
There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Full the rudder out of the
vertical stabilizer.
1F
1G
1H
2
2A 2B
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
CA
CA
First, reposition the elevator connector in place,
secure it in place using thin CA glue.
Elevator connector
CA
CA

Cut away only
the covering
both side
Realign the vertical stabilizer, then glue
the vertical stabilizer into the fuselage,
using a generous amount of thin CA.
CA
Thin CA glue
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Push the rudder and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer. There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal
stabilizer using CA glue.
2D
2E
2F
2G
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
When you are satisfied with the alignment,
use a pencil to trace around the right and
left of the stabilizer where it meets the
fuselage.
2C
CA
AB
A
A=38mm
2mm
Drill a 2mm diameter hole in torque rod
mounting slot, marking sure that you
drill the hole perpendicular to the leading
edge of the rudder.
2H 25mm tail wheel
2mm collar

Note: The slots for the control horn
installation pre- cut at factory.
Control horn
...........1
............4
4X20mm screw
2G
3
3A
............2
4X30mm screw
4mm nut-washer
4mm washer
4mm nut
4x30mm screw
Aluminum landing gear
CA
CA
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft auftreten!
3B
3C

Remove the plywood motor
mounting plate and drill a 5mm
hole through the fire-wall at
each of the four marks marked
above (D).
5mm
13/64”
Using a aluminum motor mounting plate as a template, mark
the plywood motor mounting plate where the four holes are
to be drilled (A).
Remove the aluminum motor mounting plate and drill a 3mm
hole through the plywood at each of the four marks marked (B).
Using a plywood motor mounting
plate as a template, mark the fire-
wall where the four holes are to
be drilled (C) .
! Align the mark on plywood
motor mounting with the center
mark on the fire-wall
!
Aluminum motor mounting plate
(included with electric motor set)
Plywood motor
mounting A
B
C
E
5mm
13/64”
Push the four 5x35mm bolts through
the fire-wall as shown (E)
Reposition the plywood motor
mounting plate and secure
it in place with twelve 5xmm nuts and
washers (E).
Pull the magnetic battery hatch
out of the fuselage
4C
55A
5B
5C
5D 5E

F
Firewall
113mm
B’
B
B=B’
A
A=A’
A’
! Engine thrust on balk head
is already adjust at factory
Attach the aluminum motor mounting
plate on to the motor and secure it in
place with four screws ( included with
motor set) (F).
TOP-VIEW / Draufsicht
SIDE-VIEW / Seitenansicht
Sturz und Zug beachten!
Sperrholztrager Platten zusammenkleben, wie gezeigt ausrichten
und Locher bohren.
Motor nach untenstehendem Schema einbauen.
Fur optimale Leistung empfehlen wir folgende Komponenten:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Akku LEMONRC 3700-5S
-Luftschraube 12*6 - 13*8
For maximum performance, we recommended
the following:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Battery LEMONRC 3700-5S
-Propeller 12*6 - 13*8
Throttle pushrod
FRONT
Elevator pushrod
Elevator servo
Rudder servo
(mini servo)
Throttle servo
BOARD - TOP VIEW
FUSELAGE - BOTTOM VIEW
FUSELAGE - BOTTOM VIEW
The holes for the rudder servo
are Pre-cut at factory (left and
right side of the fuselage).
Cut away only the covering
Akku Kiettband
aus dem PICHLER
Sortiment
Best.Nr. C4739
Battery seat bell
X
Tipp
5F
66A
6B 6C

1.5mm
1/16
2mm
L/R
X
X
BOTTOM - VIEW / Unteransicht
Cut here for standard servo
Aileron & flap
extension cord
Trial fit the control horn into
the slot.
If the parts will join, but with
a gaps, sand or trim the parts
a little at a time until the parts
meet exactly with no gaps.
CA
Plastic control horn
Linkage Stopper set
.....................4
.................4
1.2mm O Alenk-Gestange
Aileron & flap pushrod
CA
CA
Do the same way with other wing half
Metal hook (x2)
Spring (x1)
L/R
Do the same way with other wing half
7
8
9

65 ~ 70mm
20mm
10mm
10mm
10mm
Aileron /
Rudder
Elevator /
10mm
20mm
Querruderausschlag
Hohenruderausschlag
Seitenruderausschlag
Do not try to fly an out-of balance model!
Uberprufen Sie vor dem Flug den Schwerpunkt.
IMPORTANT:
Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
All details are subject to change
without notice !
Technische Anderungen und Irrtumer
vorbehalten !
25mm Landing / Landung
Fflap / Landeklappen
10
Note: Cut out the stickers and apply them in the
proper area. Do not peel the backing paper off all
at once.
Peel off one corner of the backing and cut off with
scissors.
Arrange sticker on model and when satisfied adhere
the corner without backing.
Carefully peel back the rest of the backing while at
the same time adhering the rest of the sticker.
Try not to make air bubbles, if there are some,
carefully puncture sticker (center of bubble) but not
model surface with the tip
of the knife or sharp pin and squeeze out the air.
At curves stretch sticker and apply a little heat so
that no ceases occur.
Cut off the excess that is produced.
11
12
15mm Take off / Start
CG

.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
6 - channel radio
RECOMMENDED ACCESSORIES (Purchase separately)
6 - Kanal
Fernsteuerung
Egänzungskit Verbrenner
(Tank + Motorträger)
Best.Nr. C4165
Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)
Antrieb Standard:
Antrieb Tuning (Kraftvoller Kunstflug):
BOOST 40 Brushless Combo Set, Best.Nr. C2983
LiPo Battery RED POWER 3200-3S, Best.Nr. C3164
Luftschraube 12*6, Best.Nr. C1937
BOOST 60 Brushless Combo Set, Best.Nr. C3174
LiPO Akku RED POWER 4250-5S, Best.Nr. C4547
Luftschraube 13*8, Best.Nr. C2846
Silikonkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
1 x Servo S4020
(für Seitenruder)
Best.Nr. C1687
3 x Servo S4020
(für Höhen- und Querruder)
Best.Nr. C4995
2 X Servo DS3012
(Fur Landeklappen)
# C4995