VQ Models FLY BABY User manual

Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
Designed for brushless electric motors (.46-.52 class glow conversion optional)
Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich)
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 63.7in.
Length 43.9 in.
Electric Motor (See next page)
Glow Engine .46 2Stroke / .52 4-Stroke
Radio 4 Channel / 4 -5 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1620mm
Lange 1115mm
Elektroantrieb (siehe nächste Seite)
Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T
Fernsteuerung 4 Kanal / 4 -5 Servos
FLY BABY

.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
4 - channel radio
RECOMMENDED ACCESSORIES (Purchase separately)
4 - Kanal
Fernsteuerung
Egänzungskit Verbrenner
(Tank + Motorträger)
Best.Nr. C4165
Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)
Antrieb Standard:
BOOST 40 Brushless Combo Set, Best.Nr. C2983
LiPo Battery RED POWER 3200-3S, Best.Nr. C3164
Luftschraube 12*6, Best.Nr. C1937
Antrieb Tuning (Kraftvoller Kunstflug):
BOOST 60 Brushless Combo Set, Best.Nr. C3174
LiPO Akku RED POWER 4250-5S, Best.Nr. C4547
Luftschraube 13*8, Best.Nr. C2846
Silikonkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
1 x Servo S4020
(für Seitenruder)
Best.Nr. C1687
3 x Servo S4020
(für Höhen- und Querruder)
Best.Nr. C4995

Cut away only
the film both
side
Cut away only
the film both side
! Securely glue together If coming off during fly, you lose
control of your air plane.
90O
BB’
90O
A=A’
AB
* WARNING: When removing any covering from the airframe,
please ensure that you secure the cut edge with CA or similar
cement. This will ensure the covering remain tight.
3/8 in. (9.5mm)
5-Push the elevator and its hinges into the hinge slots
in the trailing edge of the horizontal stabilizer. There
should be a minimal hinge gap.
6-When satisfied with the and alignment, hinge the
elevator to the horizontal stabilizer using thin CA glue.
Make sure to apply a thin layer of CA glue to the top
and bottom of both hinges and to inside the hinge
slots.
7-Repeat the previous procedures to hinge the second
elevator to the other side of the horizontal stabilizer.
Do the same way with the rudder.
Control horn
................3
2x20mm screw
..........6
Hinge STABILIZER
1TOP VIEW / Draufsicht
CA
Thin CA
1-Trial fit the horizontal stabilizer in place .
Check the alignment of the horizontal stabilizer.
When you are satisfied with the alignment, use
a pencil to trace around the top and bottom of
the stabilizer where it meets the fuselage.
2-Remove the horizontal stabilizer from the
fuselage. Using the sharp hobby knife, carefully
cut away the covering inside the lines which
were marked above, do not cut the balsa.
3-Spread epoxy (30 minute) onto the top and
bottom of the horizontal stabilizer along the
area where the covering was removed and to
the fuselage where the horizontal stabilizer
mounts.
4-Install the horizontal stabilizer into the fuselage
and adust the alignment as described in steep 1.
Allow the epoxy to cure before proceeding to
next step.
Do the same way with the vertical stabilizer.

............4
4x15mm screw
All holes pre-drilled
at factory
4x40mm screw
4mm Washer
4mm Nut
......2
.......................4
......................4
CA
1/8(3mm) screw
Collar
1.5mm
1/16
Align the engine center with
fire-wall marked line (A=A’)
A
A’
FRONT VIEW
......4
..............4
4x30mm screw
4mm Blind-nut
..........4
3x20mm screw
................4
3mm nut
3mm washer
................4
4mm washer
................4
Align the mark on both
mounts with the center
mark on the fire-wall
5mm
!
4mm
2mm
5/64
FUSELAGE
2
3BOTTOM - VIEW / Unteransicht
E
E = 110 - 113mm
4mm nut
4x40mm screw
Aluminum landing
gear
4mm
5/32”
4mm
5/32”
A
B
C
C
C
Finish
A-Locate the aluminum landing gear in
the bottom of the fuselage.
B-Drill the hole on each side of the plastic wheel pant.
C-Slide one wheel onto each of the wheel pant and secure
them with the 4x40mm screw and nut.
B
B
Full the magnetic cockpit out
of the fuselage first.
Full here
Plastic tail gear mount
3x10mm screw
2mm collar
......2
......1
......1
4

Firewall
B’
B
B=B’
A
A=A’
A’
TOP-VIEW
SIDE-VIEW
! Engine thrust on balk head
is already adjust at factory
Using a aluminum motor mounting plate as
a template, mark the plywood motor mounting
plate where the four holes are to be drilled (2).
Remove the aluminum motor mounting
plate and drill a 1/8”(3mm) hole through
the plywood at each of the four marks
marked .
3mm
2Note: The aluminum motor mounting included
with electric motor set.
! Engine thrust on balk head
is already adjust at factory
X
To muffler
Filler tube
To engine
Rubber
stopper
Cap
Stopper
4mm
5
6
7BOTTOM - VIEW / Unteransicht
E = 110 - 113mm
E
Checking for leaks - block the vents and blow into the
feed - if in doubt submersing the tank in a blow of
water will show up any problems.
Blow
Water
...4
5x70mm screw
5mm Washer
5mm Nut
..................16
.................12
CA
1
5mm

Rudder servo
Seitenruder servo
Elevator servo
Hohenruder servo
Rudder servo / Seitenruder servo
Throttle servo
FUSELAGE
TOP VIEW
CA
Magnetic cockpit
8
9
10
Cut away only
the film.
Control horn
................2
2x20mm screw
..........4
BOTTOM - VIEW / Unteransicht
Elevator pushrod (x2)
Rudder pushrod (x1)
Throttle servo
OR
Elevator servo
Hohenruder servo
Elevator
pushrod (x2)
Rudder pushrod (x1)
Adhesive
tape
1-Connect the 30cm extension (not include) to the aileron servo and secure with the adhesive tape.
2-Using the thread (pre-installed at factory), full the extension out of the wing as shown.
3-Attach the aileron servo into the wing.
4-Depending on the position of the linkage, determine the location of the aileron control horn.
The horn holes must be perfectly aligned with the axis of articulation.
5-Mark the position of the “foot” of the horn on the aileron.
6-Remove the control horn and drill two 5/64” holes through
the aileron.
7-Attach the aileron control horn using 2x20mm screw.
Do the same way with second wing half.

1- Push the 18mm (dia.) Aluminum tube
throughout the fuselage.
2- Carefully, push the right wing to the fuselage,
ensuring that they are accurately aligned.
3- Secure the right wing in place using the
5x20mm screw.
Do the same way with the left wing.
CA
6mm wooden
dowel
6mm wooden dowel
CA
CA
Do the same way with
second wing half.
Do the same way with
another half wing.
11
12
13
........4
........4
5X25mm screw 5mm washer
....2 ......2
TOP VIEW / Draufsicht
TOP VIEW / Draufsicht
Wing
8mm
Wooden dowel
Thin CA
Thin CA
Thin CA
The holes are Pre-cut
at factory

14
15
21/64”
(8mm)
7/16”
(11mm)
1”(25mm)
AILERON STROKE ELEVATOR STROKE RUDDER STROKE
CG
WARNING ! Securely install the receiver and power
pack, ensuring they will not come loose or rattle during
flight.
Never fly before checking the Cg’s required position.
In order to obtain the CG specified, reposition the receiver and power pack
3.5”(89mm)
Wing center section
21/64”
(8mm)
7/16”
(11mm) 1”(25mm)
Control surface / Ruderausschlage
Balance / Schwerpunkt
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass-
cleaner to clean on surface of your model to keep the colour not fade.
16
17
Querruderausschlag
Hohenruderausschlag
Seitenruderausschlag
Uberprufen Sie vor dem Flug den Schwerpunkt.