VQ Models Volksplane VQA133US User manual

Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 62.9in.
Length 46 in.
Electric Motor (See next page)
Radio 5 Channel / 4 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1600mm
Lange 1170mm
Elektroantrieb (siehe nächste Seite)
Fernsteuerung 5 Kanal / 4 Servos
VOLKSPLANE
U.S VERSION: VQA133US SWISS VERSION: VQA134BLUE SWISS VERSION: VQA134RED

.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
CA
Cyanoacrylate Glue
Sekundenkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
Minimum 5 channel radio
for airplane with 4 servos
Extension for aileron
servo.
REQUIRED FOR OPERATION (Purchase separately)
Motor Control
Li-Po Battery, 3700mAh.
650-800W Brushless Motor

* WARNING: When removing any covering from the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will ensure the covering remain tight.
Cut away only
the covering
4x45mm screw
4mm bolt
4mm washer
75mm wheel
Aluminum landing gear
...4
3x15mm screw
FUSELAGE - BOTTOM VIEW
4X45mm
...2
4mm ...................4
4mm.................4
1
1A 1B
1C
CA
CA

Cut away only
the covering
both sides.
Cut away only
the covering
both sides
CA
Cut away only
the covering
2
2A
2B
2C
2D
2E
Trial fit the horizontal stabilizer in place on the
fuselage. Check the alignment of the horizontal
stabilizer by measuring from a fixed point along
the center line of the fuselage to the leading edge
on each side of the horizontal stabilizer. The
distance must be equal on both sides.
Using the pencil trace around the top and bottom
of the stabilizer where it meets the fuselage.
* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.
Remove the horizontal stabilizer from the fuse-
lage. Remove the covering material from the gluing
surfaces on both the top and bottom of the horizontal
stabilizer.
NOTE: Do not glue the horizontal stabilizer into
the fuselage at this time.
NOTE: cut inside the pencil lines.
Again, slide the horizontal stabilizer into the
fuselage. Check the alignment of the horizontal
stabilizer. Secure the horizontal stabilizer in place
using the thin CA glue.
Securely glue together. If coming off during
flight, you lose control of your air plane.
Trial fit the horizontal stabilizer in place on the fuselage.
Check the alignment with the horizontal stabilizer The distance must
be equal on both sides (B=B’).
Using the pencil trace around the top and bottom of the stabilizer where it
meets the fuselage.
Remove the vertical stabilizer from the fuselage.
Remove the covering material from the gluing
surfaces on both the left and right of the vertical
stabilizer.
BB’

CA
Cut away only
the covering
After snapping, secure the
control horn flat with thin
CA glue.
CA
Thin CA
Plastic control horn
.....................1
3
Securely glue together. If coming off during
flight, you lose control of your air plane.
Again, push the vertical stabilizer into the
fuselage. Check the alignment with the horizontal
stabilizer. Secure the vertical stabilizer in place
using the thin CA glue.
3A
3B
3C
3D

Cut away only
the covering
RIGHT
WRONG
5/64”
2mm
Plastic control horn
.....................1
4
3x10mm....4
....1
....2
4A
4C
4D
Without using glue yet, push the rudder
and its hinges into the hinge slots in the
trailing edge of the vertical stabilizer.
When satisfied with the alignment, mark
the mounting hole position, where the
rudder torque rod meets the rudder with
a pencil.
Remove the rudder and drill a 2mm diameter hole in
torque rod mounting slot, making sure that you drill
the hole perpendicular to the leading edge of the
rudder.
4B
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge

5
5A
5B
Steel clevis
......2
950mm steel wire
......2
FUSELAGE - BOTTOM VIEW
FUSELAGE - TOP VIEW

4mm
6
6A
Using a aluminum motor mounting as a template,
mark the fire-wall where the four holes are to be
drilled .
Remove the motor and drill a 4mm hole
through the fire-wall at each of the four marks
marked .
...4
3x15mm
...4
6B
6C

1mm
1mm
1mm
1mm
77A 7B 7C
Adhesive tape
2x8mm
......6
2x8mm
......4
2x8mm
2x8mm
7D
7E

Cut away only
the covering
Fuselage - Top view
Rudder servo
2mm connector
...2
3mm connector
...4
CA
CA
Elevator servo
8
8A
8B
8C
Note: The holes for the connector installation
are pre-drilled at factory

L/R
BOTTOM - VIEW
Aileron pushrod
CA
CA
Do the same way with other wing half
L/R
X
X
BOTTOM - VIEW
Aileron
extension cord
Do the same way with other wing half
Control horn
..........2
2x30mm
...4
2mm
2mm connector
........2
9
9A
9B
Steel clevis
......2
175mm steel wire
......2

2mm
Note: The hole on the surface of the top of the
wing is pre-drilledat factory.
2.mm drill bit
Aluminum
tube inside 3x15mm screw
TOP A
B
3x15mm screw
.........2
Secure the wing in place
using 3x15mm screw.
10
10A
10B
10C

Note: The holes on the top of the
wing are pre-drilled at factory.
Wing brace
3x12mm
.........4
3x12mm
3x12mm
Note: The length of the wing brace can adjust by turn the
metal hook.
11
The recommended C.G (Center of Gravity) location for the Volksplane is 89 ~ 91mm
Adjust the location of the battery pack as required to achieve this C.G location.
If necessary , add weight to either the tail or nose until the correct balance is achieve.
CG
WARNING ! Securely install the receiver and power pack, ensuring they will not come loose or rattle during flight.
Never fly before checking the Cg’s required position.
78 ~ 83mm
AILERON STROKE ELEVATOR STROKE RUDDER STROKE
25/64”(10mm) 1”(25mm)
Control Surface
25/64”(10mm)
25/64”(10mm)
25/64”(10mm) 1”(25mm)
12