VQ Models Cap 10 User manual

AEROBATIC MODEL
60 Class
90 Class
2-cycle engine
4-cycle engine
INSTRUCTION MANUAL / MONTAGEANLEITUNG
RADIO CONTROLED ALMOST READY-TO-FLY ENGINE POWERED ALL BALSA PLANE
Wingspan approx. 1500mm
Fuselage lenght approx 1205mm
Electric Motor 870 Watt (PULSAR 60)
Glow Engine .61 2T / .91 4T
Radio 5 Channel / 6 Servos
Spannweiter ca. 1500mm
Lange ca. 1205mm
Elektroantrieb 870 Watt (PULSAR 60)
Verbrennerantrieb 10cc 2Takt / 15cc 4Takt
Fernsteuerung 5 Kanal / 6 Servos
SPECIFICATION TECHNISCHE DATEN

Minimum 6 channel radio
for airplane with 7 servos
.70 ~.91 - 4 cycle
12x6 for .58 - 2 cycle engine
12x7 for .61 - 2 cycle engine
12x7 for .70 - 4 cycle engine
14x6 for .91 - 4 cycle engine
Silicone tube
Extension for aileron
servo.(x2)
.58 ~ .61 - 2 cycle
.Motor control x1 .Aileron x 2
.Flap x 2 .Elevator x1 .Rudder x1
SILICON
EPOXY A
EPOXY B
CA
GLUE / Epoxy Glue ( 5 minute type)
Silicon sealer
Cyanoacrylate
Glue
Epoxy Glue (30 minute type)
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits
REQUIRED ITEMS / Zum Betrieb wird benotigt
KLEBSTOFF
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
!
If exposed to direct sunlight and / or heat, wrinkles can appear. Storing the model in a coll
place will let the wrinkles disappear. Otherwise, remove wrinkles in covering film with a hair-
dryer, starting with low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und / oder Warme kann die Folie erschlaffen bzw. Falten entstehen.
Verwenden Sie ein Warumluftgeblase (Haartrockner) um evtl. Falten aus der Folie zu
bekommen. Die Kanten konnen Sie mit einem Bugeleisen behandeln. Nicht zuviel Hitze
anwenden
Read through the manual before you begin, so you will have an overall idea of what to do.
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
Li-Po Battery
LEMONRC 4500 - 18.5v
ESC 80A
Motor Brushless
870Watt (PULSAR 60)

L/R
BOTTOM VIEW
2x10mm
screw
X
X
Flap servo hatch
(plywood)
2- Servo installation / Servoeinbau
TOP
Flap servo hatch Flap push rod
Push rod exit
Flap servo hatch
Flap servo Servo mount
1- Place the flap servo onto the servo mounts and secure it in place using
the four screws included with the servo.
2- Install the flap push rod connector onto the hole in the flap servo arm
and insert the push rod through the push rod connector.
3- Place the flap servo hatch in its mount and secure it in place using four
2x10mm screws.
Flap push rod exit
L/R
Aileron servo
Aileron
push rod
CAUTION: one of the flap servos is revert servo
2x10mm screw
3- Servo installation / Servoeinbau
1.2mm
L/R
Plastic control horn
2x20mm screw
Linkage Stopper set
............................4
.......................8
......................2
BOTTOM VIEW
1-When you are satisfied with the alignment of the control horn mark the mounting hole
positions with a felt tipped pen or a pencil.
2-Remove the control horn and drill two 2mm (5/64”) holes through the ailerons and flaps.
3-Attach the control horn using two 2x20mm screw and a back plate.
Plastic control horn
Plastic back plate
2x20mm screw
2mm
2x20mm screw
2x20mm screw
1- Servo installation / Servoeinbau
Aileron servo
extension cord
X
BOTTOM
2mm
Unteransicht
Unteransicht

4- Wheel pants installation / Fahrwerkseinbau
CA
“L”For left wing
“R”For right wing
12
Left ABS gear cover of “L” set
FRONT REAR
Right ABS gear cover of “L” set
TOP VIEW
2- Cut away two holes on the top and
bottom of the right and left ABS gear cover
for the landing gear exit
3- Fit all ABS gear cover in place (L with L and R with R) and secure them
with CA glue
L/R
BOTTOM VIEW
1- Position the landing gear and strap as
show. Using the four 3x10mm screws, fasten
the landing gear to the bottom of the wing.
CAUTION: Push down the wheel pant
to this line.
3
4
Wheel pant
3x12mm
screw(2)
ABS gear cover
Nylon gear strap
Wheel
Stopper
CA
WING
Landing gear
5
6
7
8
5- Wheel pants installation / Fahrwerkseinbau
Stopper
Wheel
Nylon gear strap
3x12mm screw
Fiber glass wheel pant
FRONT VIEW
BOTTOM VIEW
Wooden block
Wooden block
Nylon gear strap
ABS gear cover
Fiber glass wheel pant
3mm screw
(black)
BOTTOM VIEW
4.3mm
4mm screws
4mm washer
4mm nut
...................4
...................4
..........4
1- Set the engine on the engine mounts
2- Place the engine mounts with the engine to the
fire wall and secure it with tittle CA glue.
3- Using a pencil or felt tipped pen, mark the engine
mounting plate where the four holes are to be drilled
4- Remove the engine and drill a 11/64” (4.3mm)
hole through the fire wall at each of the four marks
made in Step 3 above.
CAUTION: Align the mark on both mounts with the
center mark on the fire wall
CAUTION: Engine thrust on fire wall is aleady adjust
at factory
CAUTION: Align the engine center
with fire wall marked line
6- Engine mounts / Motortrager
Unteransicht
Vorderansicht
Unteransicht
Wooden dowel
Wooden dowel
CA
L/R

In case of four-stroke engine
FRONT VIEW
Throttle push rod
X
Engine
Secure the engine to the engine mounts using fous 3x25mm screws and nuts
7- Four-stroke engine installation / Einbau Viertarktmotor
X
Engine
Secure the engine to the engine mounts using
fous 3x25mm screws and nuts
Trim the fire wall so that
your muffler doesn’t touch
with a knife or Dremel
Trim the fire wall so that
your muffler doesn’t touch
with a knife or Dremel
FRONT VIEW
In case of two-stroke engine
X
Engine
Two-stroke engine with manifold
FRONT VIEW
In case of two-stroke engine
8- Two-stroke engine installation / Einbau Zweitarktmotor
9- Two-stroke engine installation / Einbau Zweitarktmotor

6.5
LR
2
4
6
8
10
20
30
40 50H
L
02
4
6
8
10
12
-2
-4
4
6
8
10
12
16
14
18
40
60
80
100
120
160
140
180
N
W
E
S
3
6
9
12
15
18
21
24
27
33
36
39
400
500
600 100
300
200
60
02
4
6
8
10
12
-2
-4
40
60
80
100
120
160
140
180
BAT
118 ~ 122mm
TOP VIEW
10- Engine installation / Motoreinbau
Cowling mount
Cowling mount
Engine thrust on balk head
is already adjust at factory
X
To muffler
Filler tube
To engine
Draufsicht
NOTE: Place of the throttle servos
may be change depend of engine.
(Four-stoke or two-stroke engine)
Throttle servo
Elevator servo
Hohenruderservo
Drosselservo
Servo mount
Servohalterung
12- Servo installation / Servoeinbau
11- Fuel tank installation / Tankeinbau Push the fuel tank forward until
there are no gaps between the
tank and firewall.
After confirming the direction . Insert
and tighten the screw.
5/32”(4mm)

13- Joining the wing
Flachenverbindung
Aluminum tube
14- Joining the wing
Flachenverbindung
TOP VIEW Draufsicht
L/R Asemble the Left and Right wing
the same way.
TOP VIEW Draufsicht

1- Trial fit the horizontal stabilizer in place
2- Using a pencil, trace around the vertical stabilizer where it meets the fuselage. (both sides).
3- Remove the horizon stabilizer from the fuselage.
4- Using a sharp hobby knife, cut away the covering inside the lines which were marked in step 2. Do NOT cut into the
wood as this will affect the structural integrity of the stabilizer
5- Using a mixing stick, spread the epoxy on the horizontal stabilizer and fuselage where it meets the horizontal stabilizer.
6- Insert the horizontal stabilizer into the fuselage and secure it in place using masking tape and allow the epoxy to cure
completely. Using rubbing alcohol and paper towel, clean the excess epoxy.
A A’
BB’
A = A’
B = B’
AB
Cut away only
the film
Cut away only
the film
Warning: Securely glue together. If coming of during
flights, you lose control of your plane which leads
to accidents!
16- Horizontal Tail / Hohenleitwerk
15- Joining the wing / Flachenverbindung
RIGHT WING HARVEST
LEFT WING HARVEST
4mm screws & washer
......2
TOP VIEW
Draufsicht
TOP VIEW Draufsicht

2mm
WARNING! Securely glue together. If coming off
during flights, you lose control of your airplane
which leads to accidents !
18- Vertical stabilizer / Seitenleitwerk
2mm
CA
AB
1- Attach the tail gear mounting plate on the fuselage bottom
with 3x10mm self tapping screws
2- Trial fit the rudder in position, mar the mounting hole position
for the tail gear with a felt tipped pen or a pencil.
3- Remove the rudder and drill 2mm (5/64”) hole as shown.
4- Put the epoxy glue in the hole of rudder. Push the rudder in
place
2mm 2mm
WARNING! Securely glue together. If coming off
during flights, you lose control of your airplane
which leads to accidents !
10mm
Plastic control horn
2x20mm screw
............................2
.......................4
Plastic back plate
...........................2
When you are satisfied with the
alignment of the control horn mark
the mounting hole positions with a
felt tipped pen or a pencil.
Remove the control horn and drill
two 2mm (5/64”) holes through the
elevator
Insert the elevator push rod into the
elevator control horn. Attach the ele-
vator control horn using two 2x20mm
screw and a back plate.
Hinge
STABILIZER
AB
Apply 5 min.
Epoxy both the
top and bottom.
ELEVATOR
17- Horizontal Tail
Hohenleitwerk
Petroleum jelly AB
Apply 5 min.
Epoxy both the
top and bottom.

Plastic control horn
2x25mm screw
............................1
.......................2
Plastic back plate
...........................1
10mm
When you are satisfied with the
alignment of the control horn, mark
the mounting hole positions with a
felt tipped pen or a pencil.
Remove the control horn and drill
two 2mm (5/64”) holes through the
rudder
Insert the rudder push rod into the
rudder control horn. Attach the rudder
control horn using two 2x25mm screw
and a back plate.
20- Linkages / Anlenkungen
2x25mm screw
Rudder servo
2 mm
X
CA X
CA
2 mm
Connector
Elevator push rod
Linkage stoper
Throttle push rod
Included with the
radio set
TOP VIEW
Draufsicht
Magnetic cockpit deck
21- Cockpit
TOP VIEW
Draufsicht
Throttle pushrod
Elevator pushrod
Tank
19- Linkages / Anlenkungen
Rudergestange

1.5mm
2x10mm screw
2x10mm screw
1
2
3
4
5
TOP VIEW
Draufsicht
Magnetic hatch
22- Cockpit / Kabinen
TOP VIEW
Draufsicht
23- Cockpit / Kabinen
24- Cowling installation / Motorhaube
Drill holes for needle
valve, exhaust pipe
and glow-plug.
3mm
5mm
3x10mm self tapping screw
CA
Fuel tube or
nylon tube

26- Decor / Aufkleber
19/32”(15mm)
25/64”(10mm)
51/64”(20mm)
(45 ~ 50mm)
ELEVATOR CONTROL RANGE RUDDER CONTROL RANGE
Adjust the travel of each control surface to the values
in the diagrams these values fit general flight capabilites.
Readjust according to your needs and flight level.
Position for
right diagram.
AILERON CONTROL RANGE
FLAP CONTROL RANGE
CG
27- Balance and control range
Schwerpunkt - Ruderausschlage
Sticker
(75 ~ 78mm)
Position for right diagram.
Position for right diagram.
NEVER FLY BEFORE CHECKING THE CG’S REQUIRED POSITION.
2.9 ~ 3”
1.7”~1.9”
(45 ~ 50mm)
1.7”~1.9”
51/64”(20mm)
51/64”(20mm)
Trim the cowl with a knife or Dremel so that your engine and muffler don’t touch
Fix the cowling with the 3x10mm self tapping screws on the cowling mounts.
3mm
Drill holes for needle valve
and glow-plug
Drill holes for needle valve
and glow-plug
3x10mm self tapping screw
BOTTOM VIEW
Unteransicht
25- Cowling installation / Motorhaube
VQ / CAP-10 VERSION 3