Walker Edison BTSPIN User manual

BTSPIN

Part 1: Spindle
Part 2: Top rail
Part 3: Botton Rail
Part 4: Support Bean
Part 5: Bracket
Part 6: Right Side Rail
Part 7: Left Side Rail
Part 8: Feet
Part 9 : Back Rail
Part 10: Front Rail
Part 11: Slats
Part 12: Bottom Headboard Slat
2
3
4
8
4
6
7
8
8
8
10
11 11 11 11
11
11 11 11 11 11 11
11
11
12

08 pcs
17 pcs
30 pcs
14 pcs
05 pcs
05 pcs
05 pcs
06 pcs
11 pcs
20
10x40mm

9
10
5
1
6
7
10
Connect parts (9,10) to parts (7,6)
Secure parts with screw (O)
Insert wooden dowels (E) into rails (5,9,10), dowels (F) into parts (4),
4
O
O
O
O
O

Connect parts (9,10) to parts (6,7) With Bolt (A) for this use the Hex key (J)
6
7
9
10
Attach Feet (8) to frame parts (7,6) using screw (M) and Union Screw (N). Union Screw (N) Should be on the inside
of the bed frame, with screw (M),on the outside of the leg. Tighten by using with hex key(J) on both ends of the screw
at the same time. The use Screw (D) and hex key (J) to secure legs(8).
J
J
J
J
J
J
J
J
J
J
M
N
6
10
8
8
8
8
9
J
J
J
J
J
J
J
J
J
J
J
J
N
N
N
N
7
M
M
M
M
J
M
NJ
J

PPP
P
Q
8
8
8
8
7
10
Secure feet to frame using screw(C).
Attach the metal connector plate (Q) to the 2 corners of the bed with screws (P). Take care to
aligne the plate over the sean of the two parts, as shown in the drawing, before seguring in place.
3
connect parts (5) and (3). Note the drawing for location of pocket hole.
Secure parts(5) to part (3) using screw (O)
Q
P20mm
30mm
O40mm
O
O

2
4
4
Connect parts (2) to parts (4) using bolt (D) and hex key (J).
2
4
4
4
Connect parts (5) to parts (4) using bolt D and hex key (L)
J
J
J
J
J

4
4
1
1
1
1
1
1
1
1
1
Insert Spindles (1) in holes on part (3)
3
Attach Spindles (1) in the part (2) using screw ( C )
1
1
1
1
1
1
1
1
1
2
30mm

20mm
Insert Headboard slat (12) on part (3), with screw ( B),
secure more 3 Screw (P) in Spindles (1)
P
P
12
Insert Wood Dowel (E) in holes to part (12)
12
30mm
P
B
B
B
B
B
E
E

7
6
10
Secure slat (11) Using Screw (B) and slat spacer (L)
11
11
11 11
11 11
11 11
11
11 11 11
Attach base Headboard (5,3) on holes of the frame (9) using Bolt (G), washer (H),
and nut (I) Tighten using both the hex key (J) and wrench(K)
L
L
L
J
G
I
H
K
Align Wood Dowels
Here
30mm
B

Final Assembly
P.12