WE-EF ETC130-FS LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC130-FS LED
EVC130-FS LED
ETC140-FS LED
EVC140-FS LED

1
Inground Luminaire
ETC130-FS
ETC140-FS
EVC130-FS
EVC140-FS
IP67, Class I, ta = 40°C

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.

3
Installation Methods
For proper installation, use the supplied installation
blockout.
Ensure that proper drainage is provided for the shown
installation methods:
In landscape areas, sand with gravel base (Fig. I).
In paved areas, concrete with gravel base (Fig. II).
Fig. IIFig. I
Installation
The product must be installed and maintained by a
suitably qualiƂed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.

4
Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure a suitable recess is provided to accommo-
date installation blockout/mounting ring assembly
B/M.
2) Set installation blockout/mounting ring assembly
B/M in position and ensure that:
a) Arrow Ron mounting ring Mis pointed towards
the object to be illuminated (wall, tree, column).
b) Mounting ring Mis ƃush with surface F. If the
ƃoor will be tiled or paved afterwards, leave an
appropriate gap.
c) Mains supply cable(s) Ois of sufƂcient length to
connect sealable junction box Jwith cable Efrom
luminaire.
3) During ongoing earth and/or masonry works, do
not remove stickers on Ƃxing thread holes D.
Ensure that installation blockout/mounting ring
assembly B/M is not damaged and has maintained
its original shape. If necessary use a cover plate.
Phase Two
Luminaire Installation and Electrical Connection
4) Switch off mains electrical supply.
5) Check that rating shown on luminaire label conforms
with mains electrical supply.
6) Terminate cable Efrom luminaire housing Aand
mains supply cable O(for individual wiring) or
branch cable (for through wiring) in sealable junc-
tion box J– to connect cable(s). Follow the seal-
able junction box termination instruction included
in the packaging.
7) Peel-off stickers on Ƃxing thread holes D. Set cables
and sealable junction box Jinside installation
blockout/mounting ring assembly B/M.
For wallwash illumination only
Ensure the arrow indicated on the sticker is facing
the illuminated surface (Fig. IV)
8) Loosen countersunk screws C (do not turn out).
Insert mounting lever Lbetween head of counter-
sunk screws C and cover lens. Place luminaire
housing Ainto installation blockout/mounting ring
assembly B/M(Fig. III) while aligning holes Don
mounting ring M.
Warning: When luminaire is placed inside installa-
tion blockout B, ensure there is no stress on seal-
able junction box Jor electric cables (Fig. V).
9) Tighten countersunk screws C 'hand-tight'.

5
Fig. III

6
Fig. V
Fig. IV
DIRECT LUMINAIRE TOWARDS WALL
Remove label before operation of luminaire.
TH0717W

TO9125W0918 © WE-EF 2018
Technical speciƂcations are
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]