WEG CFW100 series Owner's manual

Motors | Automation | Energy | Transmission & Distribution | Coatings
Frequency Inverter
Micro Mini Drives
Programming Manual

Programming Manual
Language: English
Document: 123456789AB / 00
Build 1414
Publication Date: 12/2018

SUMMARY OF REVISIONS
The information below describes the reviews made in this manual.
Revision Description
R00
First Edition
Applied to CFW100 frequency inverters version V3.00 or newer
Applied to CFW300 frequency inverters version V2.00 or newer

CONTENTS
1 QUICK REFERENCE OF ALARMS AND FAULTS .......................... 1-1
2 SAFETY NOTICES .................................................................... 2-1
2.1 SAFETY NOTICES IN THIS MANUAL .................................................................. 2-1
2.2 SAFETY NOTICES ON THE PRODUCT................................................................ 2-1
2.3 PRELIMINARY RECOMMENDATIONS ................................................................ 2-2
3 GENERAL INFORMATION .......................................................... 3-1
3.1 TERMINOLOGY AND DEFINITIONS ................................................................... 3-1
3.1.1 Terms and Definitions Used............................................................................ 3-1
3.1.2 Numerical Representation ............................................................................. 3-2
3.1.3 Symbols to Describe Parameter Properties ....................................................... 3-2
4 ABOUT THE HMI ...................................................................... 4-1
4.1 USE OF THE HMI TO OPERATE THE INVERTER .................................................... 4-1
4.2 INDICATIONS ON THE HMI DISPLAY ................................................................. 4-1
4.3 OPERATING MODES OF THE HMI ..................................................................... 4-1
5 HMI ........................................................................................ 5-1
5.1 ACCESS ................................................................................................... 5-1
5.2 INDICATIONS ............................................................................................. 5-3
6 FREQUENCY INVERTER IDENTIFICATION ................................... 6-1
6.1 INVERTER MODEL ....................................................................................... 6-1
6.2 ACCESSORIES ........................................................................................... 6-3
7 COMMAND AND REFERENCES ................................................. 7-1
7.1 REFERENCE SOURCE SELECTION ................................................................... 7-1
7.2 SPEED REFERENCE ..................................................................................... 7-6
8 MOTOR CONTROL ................................................................... 8-1
8.1 COMMON FUNCTIONS ................................................................................. 8-1
8.1.1 Ramps ....................................................................................................... 8-1
8.1.2 Regulation .................................................................................................. 8-3
8.1.2.1 DC Link Voltage ........................................................................8-3
8.1.2.1.1 DC Link Voltage Limitation by “Ramp Hold” (P150 = 0 or 2) ...........8-3
8.1.2.1.2 DC Link Voltage Limitation by “Accelerate Ramp” (P150 = 1 or 3)....8-4
8.1.2.2 Output Current..........................................................................8-7
8.1.2.2.1 Output Current Limitation by “Ramp Hold” (P150 = 2 or 3) ............8-7
8.1.2.2.2 Current Limitation Type “Decelerate Ramp” (P150 = 0 or 1) ...........8-7
8.1.2.3 Switching Frequency ..................................................................8-8
8.1.3 Flying Start / Ride-Through ............................................................................ 8-9
8.1.4 DC Braking .................................................................................................8-10
8.1.5 Dynamic Braking..........................................................................................8-12
8.1.6 Skip Frequency ............................................................................................8-13
8.1.7 Fire Mode ...................................................................................................8-14
8.1.8 Control Configuration ...................................................................................8-16
8.2 V/F..........................................................................................................8-18
8.2.1 Energy Saver (EOC) ......................................................................................8-24
8.3 VVW ........................................................................................................8-25
9 I/O .......................................................................................... 9-1
9.1 ANALOG INPUTS......................................................................................... 9-1
9.2 NTC SENSOR INPUT .................................................................................... 9-5

CONTENTS
9.3 SIGNAL POTENTIOMETER INPUT..................................................................... 9-5
9.4 ANALOG OUTPUTS ...................................................................................... 9-6
9.5 FREQUENCY INPUT .....................................................................................9-10
9.6 DIGITAL INPUTS .........................................................................................9-11
9.7 INPUT FOR INFRARED RECEIVER ....................................................................9-20
9.8 DIGITAL OUTPUTS .......................................................................................9-20
10 FAULTS AND ALARMS ..............................................................10-1
10.1 FAULT HISTORY ..........................................................................................10-1
10.2 FAULT CONTROL ........................................................................................10-2
10.3 PROTECTIONS ...........................................................................................10-3
10.3.1 Inverter ......................................................................................................10-3
10.3.1.1 DC Link Voltage Supervision .........................................................10-3
10.3.1.2 Temperature control ...................................................................10-3
10.3.2 Motor.........................................................................................................10-4
11 READ ......................................................................................11-1
12 COMMUNICATION....................................................................12-1
12.1 COMMANDS AND COMMUNICATION STATUS......................................................12-1
12.2 SERIAL.....................................................................................................12-2
12.3 BLUETOOTH ..............................................................................................12-3
12.4 CANOPEN AND DEVICENET ...........................................................................12-4
12.5 PROFIBUS DP ............................................................................................12-7
12.6 ETHERNET ................................................................................................12-8
13 SOFTPLC ................................................................................13-1
13.1 COMMAND AND STATUS ...............................................................................13-1
13.2 USER.......................................................................................................13-2
14 APPLICATIONS ........................................................................14-1
14.1 PID CONTROLLER .......................................................................................14-1
14.1.1 Start-Up .....................................................................................................14-3
14.1.2 Academic PID Controller ...............................................................................14-5
14.1.3 Parameters .................................................................................................14-5
14.1.4 Sleep Mode .................................................................................................14-14
15 APPLICATION EXAMPLES .........................................................15-1
15.1 ANALOG INPUTS APPLICATIONS .....................................................................15-1
15.1.1 Appication 1 - Simple application (nominal speed) ..............................................15-2
15.1.2 Application 2 - Simple application (overspeed) ...................................................15-3
15.1.3 Application 3 - Analog input with reversing .......................................................15-4
15.1.4 Application 4 - Analog input with dead zone ......................................................15-5
15.1.5 Application 5 - Simple application 2 (nominal speed, inverted analog input) .............15-6

0
QUICK REFERENCE OF PARAMETERS
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P000 Access to Parameters 0 to 9999 5-1
P001 Speed Reference 0 to 9999 ro 11-1
P002 Output Speed (Motor) 0 to 9999 ro 11-1
P003 Motor Current 0.0 to 40.0 A ro 11-1
P004 DC Link Voltage 0 to 828 V ro 11-1
P005 Output Frequency (Motor) 0.0 to 400.0 Hz ro 11-1
P006 Inverter Status 0 = Ready
1 = Run
2 = Undervoltage
3 = Fault
4 = Self-Tuning
5 = Configuration
6 = DC Braking
7 = Reserved
8 = Fire Mode
ro 11-2
P007 Output Voltage 0 to 480 V ro 11-3
P009 Motor Torque -200.0 to 200.0 % ro, VVW 11-4
P011 Power Factor 0.00 to 1.00 ro 8-24
P012 DI8 to DI1 Status 0 to FF (hexa)
Bit 0 = DI1
Bit 1 = DI2
Bit 2 = DI3
Bit 3 = DI4
Bit 4 = DI5
Bit 5 = DI6
Bit 6 = DI7
Bit 7 = DI8
ro 9-12
P013 DO4 to DO1 Status 0 to F (hexa)
Bit 0 = DO1
Bit 1 = DO2
Bit 2 = DO3
Bit 3 = DO4
ro 9-20
P014 (*) AO1 Value 0.0 to 100.0 % ro 9-7
P015 (*) AO2 Value 0.0 to 100.0 % ro 9-7
P018 AI1 Value -100.0 to 100.0 % ro 9-1
P019 (*) AI2 Value -100.0 to 100.0 % ro 9-1
P020 (*) Potentiometer Signal Value -100.0 to 100.0 % ro 9-5
P022 FI Value in Hz 0 to 3000 Hz ro 9-10
P023 Main SW Version 0.00 to 99.99 ro 6-1
P024 (*) IO Acces. SW Version 0.00 to 99.99 ro 6-3
P025 (*) Comm. Acces. SW Version 0.00 to 99.99 ro 6-3
P027 Config. Acces. IO 0 to 10 ro 6-3
P028 Config. Comm. Acces. 0 to 10 ro 6-3
P029 Power HW Configuration 0 = Not identified
1 = 1.6A/110V
2 = 2.6A/110V
3 = 4.2A/110V
4 = 6.0A/110V
5 = 1.6A/220V
6 = 2.6A/220V
7 = 4.2A/220V
8 = 6.0A/220V
9 = 7.3A/220V
10 = 10.0A/220V
11 = 15.2A/220V
12 to 19 = Reserved
20 = 1.1A/380V
21 = 1.8A/380V
22 = 2.6A/380V
23 = 3.5A/380V
24 = 4.8A/380V
25 = 6.5A/380V
26 = 8.2A/380V
27 = 10.0A/380V
28 = 12.0A/380V
29 = 15.0A/380V
ro 6-1
P030 Module Temperature -200.0 to 200.0 ºC ro 11-4
Micro Mini Drives | 0-7

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P037 Motor Overload Ixt 0.0 to 100.0 % ro 10-4
P038 (*) Encoder Speed -9999 to 9999 rpm ro 11-4
P039 (*) Encoder Pulses Count 0 to 9999 ro 11-4
P045 Fan Enabled Time 0 to FFFF (hexa) ro 11-5
P047 CONF Status 0 to 33 (Table 11.2 on page 11-5) ro 11-5
P048 Present Alarm 0 to 999 ro 10-1
P049 Present Fault 0 to 999 ro 10-1
P050 Last Fault 0 to 999 ro 10-1
P051 Current At Last Fault 0.0 to 40.0 A ro 10-1
P052 DC Link At Last Fault 0 to 828 V ro 10-1
P053 Frequency At Last Fault 0.0 to 400.0 Hz ro 10-2
P054 Temperature Last Fault 0.0 to 200.0 ºC ro 10-2
P060 Second Fault 0 to 999 ro 10-1
P070 Third Fault 0 to 999 ro 10-1
P080 Last Fault on Fire Mode 0 to 999 ro 10-2
P081 Second Fault on Fire Mode 0 to 999 ro 10-2
P082 Third Fault on Fire Mode 0 to 999 ro 10-2
P100 Acceleration Time 0.1 to 999.9 s 8-2
P101 Deceleration Time 0.1 to 999.9 s 8-2
P102 Acceleration Time 2nd Ramp 0.1 to 999.9 s 8-2
P103 Deceleration Time 2nd Ramp 0.1 to 999.9 s 8-2
P104 Ramp S 0 = Inactive
1 = Active
cfg 8-2
P105 1st / 2nd Ramp Selection 0 = 1st Ramp
1 = 2nd Ramp
2 = DIx
3 = Serial/USB
4 = Reserved
5 = CO/DN/DP/ETH
6 = SoftPLC
8-3
P106 Emer. R. Acceleration Time 0.1 to 999.9 s 8-2
P107 Emer. R. Time Deceleration 0.1 to 999.9 s 8-2
P120 Speed Ref. Backup 0 = Inactive
1 = Active
2 = Backup by P121
7-7
P121 Reference via HMI 0.0 to 400.0 Hz 7-7
P122 JOG Reference -400.0 to 400.0 Hz 7-8
P124 Multispeed Ref. 1 -400.0 to 400.0 Hz 7-8
P125 Multispeed Ref. 2 -400.0 to 400.0 Hz 7-8
P126 Multispeed Ref. 3 -400.0 to 400.0 Hz 7-8
P127 Multispeed Ref. 4 -400.0 to 400.0 Hz 7-8
P128 Multispeed Ref. 5 -400.0 to 400.0 Hz 7-8
P129 Multispeed Ref. 6 -400.0 to 400.0 Hz 7-8
P130 Multispeed Ref. 7 -400.0 to 400.0 Hz 7-8
P131 Multispeed Ref. 8 -400.0 to 400.0 Hz 7-8
P133 Minimum Frequency 0.0 to 400.0 Hz 7-9
P134 Maximum Frequency 0.0 to 400.0 Hz 7-9
P135 Maximum Output Current 0.0 to 40.0 A V/f 8-7
P136 Manual Torque Boost 0.0 to 30.0 % V/f 8-21
P137 Automatic Torque Boost 0.0 to 30.0 % V/f 8-22
P138 Slip Compensation -10.0 to 10.0 % V/f 8-22
P139 Output Current Filter 0.000 to 9.999 s V/f, VVW 8-8
P140 Slip Com. Filter 0.000 to 9.999 s VVW 8-31
P142 Maximum Output Voltage 0.0 to 100.0 % cfg, V/f 8-23
P143 Intermediate Output Voltage 0.0 to 100.0 % cfg, V/f 8-23
P145 Field Weakening Speed 0.0 to 400.0 Hz cfg, V/f 8-23
P146 Intermediate Frequency 0.0 to 400.0 Hz cfg, V/f 8-23
P149 DC Link Comp. Mode 0 = Inactive
1 = Standard
2 = Overmodulation
3 = Extended
cfg, V/f 8-4
0-8 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P150 DC/LC Regul. Type 0 = hold_Ud and decel_LC
1 = accel_Ud and decel_LC
2 = hold_Ud and hold_LC
3 = accel_Ud and hold_LC
cfg, V/f, VVW 8-3
P151 DC Link Regul. Level 325 to 810 V V/f, VVW 8-5
P153 Dynamic Braking Level 348 to 800 V V/f, VVW 8-12
P156 Rated Speed Overload Current 0.1 to 40.0 A 10-5
P157 Overl.Curr.50 % Speed 0.1 to 40.0 A 10-5
P158 Overl.Curr.20 % Speed 0.1 to 40.0 A 10-5
P178 Rated Flux 50.0 to 150.0 % VVW 8-32
P200 Password 0 = Inactive
1 = Active
2 to 9999 = New Password
cfg 5-1
P202 Type of Control 0 = V/f
1 = Quadratic V/f
2 to 4 = Not Used
5 = VVW
cfg 8-1
P204 Load/Save Parameters 0 to 4 = Not Used
5 = Load 60Hz
6 = Load 50Hz
7 = Load User
8 = Not Used
9 = Save User
10 = Not Used
11 = Load Default SoftPLC
12 to 13 = Reserved
cfg 5-2
P205 Main Display Parameter 0 to 999 5-3
P207 Bar Graph Parameter 0 to 999 5-3
P208 Ref. Scale Factor 1 to 9999 5-3
P209 Ref. Eng. Unit 0 to 1 = Without unit
2 = Volt (V)
3 = Hertz (Hz)
4 = Without unit
5 = Percent (%)
6 = Without unit
7 = Rotation/min. (rpm)
5-3
P210 Ref. Decimal Point 0 = wxyz
1 = wxy.z
2 = wx.yz
3 = w.xyz
5-4
P213 Bar Scale Factor 1 to 9999 5-4
P219 Red. Switch. Freq. 0.0 to 15.0 Hz cfg 8-8
P220 LOC/REM Selection Source 0 = Always Local
1 = Always Remoto
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (LOC)
6 = Serial/USB (REM)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (LOC)
10 = CO/DN/DP/ETH (REM)
11 = SoftPLC
cfg 7-4
P221 LOC Reference Sel. 0 = HMI
1 = AI1
2 = AI2
3 = Potentiometer
4 = FI
5=AI1+AI2>0
6 = AI1 + AI2
7 = E.P.
8 = Multispeed
9 = Serial/USB
10 = Not Used
11 = CO/DN/DP/ETH
12 = SoftPLC
13 = Not Used
14 = AI1 > 0
15 = AI2 > 0
16 = Potentiometer > 0
17=FI>0
cfg 7-4
P222 REM Reference Selection See options in P221 cfg 7-4
Micro Mini Drives | 0-9

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P223 LOC FWD/REV Selection 0 = Foward
1 = Reverse
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (FWD)
6 = Serial/USB (REV)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (FWD)
10 = CO/DN/DP/ETH (REV)
11 = Not Used
12 = SoftPLC
cfg 7-5
P224 LOC Run/Stop Sel. 0 = HMI Keys
1 = DIx
2 = Serial/USB
3 = Not Used
4 = CO/DN/DP/ETH
5 = SoftPLC
cfg 7-5
P225 LOC JOG Selection 0 = Disabled
1 = Not Used
2 = DIx
3 = Serial/USB
4 = Not Used
5 = CO/DN/DP/ETH
6 = SoftPLC
cfg 7-6
P226 REM FWD/REV Selection See options in P223 cfg 7-5
P227 REM Run/Stop Selection See options in P224 cfg 7-5
P228 REM JOG Selection See options in P225 cfg 7-6
P229 Stop Mode Selection 0 = Ramp to Stop
1 = Coast to Stop
cfg 7-6
P230 Dead Zone (AIs and FI1 ) 0 = Inactive
1 = Active
cfg 9-1
P231 AI1 Signal Function 0 = Speed Ref.
1 to 3 = Not Used
4 = PTC
5 to 6 = Not Used
7 = PLC Use
8 = Application Function 1
9 = Application Function 2
10 = Application Function 3
11 = Application Function 4
12 = Application Function 5
13 = Application Function 6
14 = Application Function 7
15 = Application Function 8
16 = Control Setpoint
17 = Process Variable
cfg 9-2
P232 AI1 Input Gain 0.000 to 9.999 9-3
P233 AI1 Input Signal 0 = 0 to 10 V / 20 mA
1 = 4 to 20 mA
2=10V/20mAto0
3 = 20 to 4 mA
9-3
P234 AI1 Input Offset -100.0 to 100.0 % 9-4
P235 AI1 Input Filter 0.00 to 16.00 s 9-4
P236 (*) AI2 Signal Function See options in P231 cfg 9-2
P237 (*) AI2 Input Gain 0.000 to 9.999 9-3
P238 (*) AI2 Input Signal See options in P233 9-3
P239 (*) AI2 Input Offset -100.0 to 100.0 % 9-4
P240 (*) AI2 Input Filter 0.00 to 16.00 s 9-5
P241 (*) Potentiometer Signal Function 0 = Speed Ref.
1 to 6 = Not Used
7 = SoftPLC
8 = Application Function 1
9 = Application Function 2
10 = Application Function 3
11 = Application Function 4
12 = Application Function 5
13 = Application Function 6
14 = Application Function 7
15 = Application Function 8
16 to 17 = Not Used
cfg 9-6
P242 (*) Potentiometer Signal Gain 0.000 to 9.999 9-6
P244 (*) Potentiometer Signal Offset -100.0 to 100.0 % 9-6
0-10 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P245 Potentiometer and FI1 Filter 0.00 to 16.00 s 9-6
P246 FI1 Input Function 0 = Inactive
1 = Active in DI1
2 = Active in DI2
3 = Active in DI3
4 = Active in DI4
cfg 9-11
P247 FI1 Input Gain 0.000 to 9.999 9-11
P248 FI1 Minimum Input 1 to 3000 Hz 9-11
P249 FI1 Input Offset -100.0 to 100.0 % 9-11
P250 FI1 Maximum Input 1 to 3000 Hz 9-11
P251 (*) AO1 Output Function 0 = Speed Ref.
1 = Not Used
2 = Real Speed
3 to 4 = Not Used
5 = Output Current
6 = Not Used
7 = Active Current
8 to 10 = Not Used
11 = Motor Torque
12 = SoftPLC
13 to 15 = Not Used
16 = Motor Ixt
17 = Not Used
18 = P696 Value
19 = P697 Value
20 = Not Used
21 = Application Function 1
22 = Application Function 2
23 = Application Function 3
24 = Application Function 4
25 = Application Function 5
26 = Application Function 6
27 = Application Function 7
28 = Application Function 8
29 = Control Setpoint
30 = Process Variable
9-7
P252 (*) AO1 Output Gain 0.000 to 9.999 9-8
P253 (*) AO1 Output Signal 0 = 0 to 10 V
1=0to20mA
2=4to20mA
3=10Vto0
4=20mAto0
5=20to4mA
9-9
P254 (*) AO2 Output Function See options in P251 9-8
P255 (*) AO2 Output Gain 0.000 to 9.999 9-8
P256 (*) AO2 Output Signal See options in P253 9-9
Micro Mini Drives | 0-11

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P263 DI1 Input Function 0 = Not Used
1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Foward Run
5 = Reverse Run
6 = Start
7 = Stop
8 = Direction of Rotation
9 = LOC/REM
10 = JOG
11 = Accelerate E.P.
12 = Decelerate E.P.
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab. Flying Start
25 = Not Used
26 = Lock Prog.
27 to 31 = Not Used
32 = 2nd ramp Multispeed
33 = 2nd ramp Increase EP
34 = 2nd ramp Decrease EP
35 = 2nd ramp FWD Run
36 = 2nd ramp REV Run
37 = Start / Inc. EP
38 = Dec. EP / Stop
39 = Stop
40 = Safety Switch
41 = Application Function 1
42 = Application Function 2
43 = Application Function 3
44 = Application Function 4
45 = Application Function 5
46 = Application Function 6
47 = Application Function 7
48 = Application Function 8
49 = Enable Fire Mode
50 to 54 = Not Used
55 = Run/Stop with Line Start Lockout
cfg 9-12
0-12 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P264 DI2 Input Function 0 = Not Used
1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Foward Run
5 = Reverse Run
6 = Start
7 = Stop
8 = Direction of Rotation
9 = LOC/REM
10 = JOG
11 = Accelerate E.P.
12 = Decelerate E.P.
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Progr. Off
27 to 31 = Not Used
32 = 2nd ramp Multispeed
33 = 2nd ramp Increase EP
34 = 2nd ramp Decrease EP
35 = 2nd ramp FWD Run
36 = 2nd ramp REV Run
37 = Turn ON / Ac. E.P.
38 = De. E.P. / Turn OFF
39 = Stop
40 = Safety Switch
41 = Application Function 1
42 = Application Function 2
43 = Application Function 3
44 = Application Function 4
45 = Application Function 5
46 = Application Function 6
47 = Application Function 7
48 = Application Function 8
49 = Enable Fire Mode
50 = PID Manual / Automatic
51 to 54 = Not Used
55 = Run/Stop with Line Start Lockout
cfg 9-12
Micro Mini Drives | 0-13

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P265 DI3 Input Function 0 = Not Used
1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Foward Run
5 = Reverse Run
6 = Start
7 = Stop
8 = Direction of Rotation
9 = LOC/REM
10 = JOG
11 = Accelerate E.P.
12 = Decelerate E.P.
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Lock Prog.
27 to 31 = Not Used
32 = 2nd ramp Multispeed
33 = 2nd ramp Increase EP
34 = 2nd ramp Decrease EP
35 = 2nd ramp FWD Run
36 = 2nd ramp REV Run
37 = Start / Inc. EP
38 = Dec. EP / Stop
39 = Stop
40 = Safety Switch
41 = Application Function 1
42 = Application Function 2
43 = Application Function 3
44 = Application Function 4
45 = Application Function 5
46 = Application Function 6
47 = Application Function 7
48 = Application Function 8
49 = Enable Fire Mode
50 = Not Used
51 = Command to Increase the Control
Setpoint (EP)
52 = Not Used
53 = 1st DI for Control Setpoint Selection
54 = Not Used
55 = Run/Stop with Line Start Lockout
cfg 9-12
0-14 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P266 DI4 Input Function 0 = Not Used
1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Foward Run
5 = Reverse Run
6 = Start
7 = Stop
8 = Direction of Rotation
9 = LOC/REM
10 = JOG
11 = Accelerate E.P.
12 = Decelerate E.P.
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Progr. Off
27 to 31 = Not Used
32 = 2nd ramp Multispeed
33 = 2nd ramp Increase EP
34 = 2nd ramp Decrease EP
35 = 2nd ramp FWD Run
36 = 2nd ramp REV Run
37 = Start / Inc. EP
38 = Dec. EP / Stop
39 = Stop
40 = Safety Switch
41 = Application Function 1
42 = Application Function 2
43 = Application Function 3
44 = Application Function 4
45 = Application Function 5
46 = Application Function 6
47 = Application Function 7
48 = Application Function 8
49 = Enable Fire Mode
50 to 51 = Not Used
52 = Command to Decrease the Control
Setpoint (EP)
53 = Not Used
54 = 2nd DI for Control Setpoint Selection
55 = Run/Stop with Line Start Lockout
cfg 9-12
P267 (*) DI5 Input Function See options in P263 cfg 9-12
P268 (*) DI6 Input Function See options in P263 cfg 9-12
P269 (*) DI7 Input Function See options in P263 cfg 9-12
P270 (*) DI8 Input Function See options in P263 cfg 9-13
P271 DIs Function 0 = (DI1..DI8) NPN
1 = (DI1..DI4) PNP
2 = (DI5..DI8) PNP
3 = (DI1..DI8) PNP
cfg 9-15
Micro Mini Drives | 0-15

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P275 DO1 Function 0 = Not Used
1 = F* ≥ Fx
2 = F ≥ Fx
3 = F ≤ Fx
4 = F = F*
5 = Not Used
6 = Is > Ix
7 = Is < Ix
8 = Torque > Tx
9 = Torque < Tx
10 = Remote
11 = Run
12 = Ready
13 = No Fault
14 = No F070
15 = Not Used
16 = No F021/F022
17 = Not Used
18 = No F072
19 = 4-20mA OK
20 = P695 Value
21 = Forward
22 to 23 = Not Used
24 = Ride-Through
25 = Pre-Charge OK
26 = Fault
27 = Not Used
28 = SoftPLC
29 to 34 = Not Used
35 = No Alarm
36 = Without fault and alarm
37 = Application Function 1
38 = Application Function 2
39 = Application Function 3
40 = Application Function 4
41 = Application Function 5
42 = Application Function 6
43 = Application Function 7
44 = Application Function 8
45 = Fire Mode ON
46 = Low Level of Process Variable
47 = High Level of Process Variable
9-21
P276 (*) DO2 Function See options in P275 9-21
P277 (*) DO3 Function See options in P275 9-21
P278 (*) DO4 Function See options in P275 9-22
P281 Fx Frequency 0.0 to 400.0 Hz 9-23
P282 Fx Hysteresis 0.0 to 15.0 Hz 9-24
P290 Ix Current 0.0 to 40.0 A 9-24
P293 Tx Torque 0 to 200 % 9-24
P295 Inverter Rated Current 1.1 to 15.2 A ro 6-2
P296 Line Rated Voltage 0 = Reserved
1 = 110 - 127 Vac
2 = 200 - 240 Vac | 310 Vdc
3 = Reserved
4 = 380 Vac | 513 Vdc
5 = 415 Vac | 560 Vdc
6 = 440 Vac | 594 Vdc
7 = 480 Vac | 650 Vdc
cfg 6-3
P297 Switching Frequency 2.5 to 15.0 kHz cfg, V/f, VVW 8-9
P299 DC Braking Start Time 0.0 to 15.0 s V/f, VVW 8-11
P300 DC Braking Stop Time 0.0 to 15.0 s V/f, VVW 8-11
P301 DC Braking Frequency 0.0 to 15.0 Hz V/f, VVW 8-12
P302 DC Braking Current 0.0 to 100.0 % V/f, VVW 8-12
P303 Skip Frequency 1 0.0 to 400.0 Hz V/f, VVW 8-13
P304 Skip Frequency 2 0.0 to 400.0 Hz V/f, VVW 8-14
P306 Skip Band 0.0 to 25.0 Hz V/f, VVW 8-14
P308 Serial Address 1 to 247 cfg 12-2
P310 Serial Baud Rate 0 = 9600 bits/s
1 = 19200 bits/s
2 = 38400 bits/s
cfg 12-2
0-16 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P311 Serial Bytes Config. 0 = 8 bits, no, 1
1 = 8 bits, even,1
2 = 8 bits, odd, 1
3 = 8 bits, no, 2
4 = 8 bits, even,2
5 = 8 bits, odd, 2
cfg 12-2
P312 Serial Protocol 0 to 1 = Reserved
2 = Modbus RTU Slave
3 to 4 = Reserved
5 = ModBus RTU Master
cfg 12-3
P313 Action for Comminic. Error 0 = Inactive
1 = Ramp Stop
2 = General Disable
3 = Go to LOC
4 = LOC Keep Enab.
5 = Cause Fault
12-3
P314 Serial Watchdog 0.0 to 999.0 s cfg 12-3
P316 Serial Interf. Status 0 = Inactive
1 = Active
2 = Watchdog Error
ro 12-3
P320 Flying Start / Ride-Through 0 = Inactive
1 = Flying Start
2=FS/RT
3 = Ride-Through
cfg 8-9
P331 Voltage Ramp for FS and RT 0.2 to 60.0 s 8-10
P332 Dead Time 0.1 to 10.0 s 8-10
P340 Auto-Reset Time 0 to 255 s 10-2
P352 Fan Control Config. 0 = OFF
1 = ON
2 = CT
cfg 10-3
P358 (*) Encoder Fault Config. 0 = Inactive
1 = F067 ON
2 = F079 ON
3 = F067 and F079 ON
cfg 10-3
P375 (*) NTC Temperature 0 to 200 ºC ro 9-5
P397 Control Config 0 to F (hexa)
Bit 0 = Slip Compens. Regen.
Bit 1 = Dead Time Comp.
Bit 2 = Is Stabilization
Bit 3 = P297 reduction in A050
cfg 8-16
P399 Motor Rated Efficiency 50.0 to 99.9 % cfg, VVW 8-32
P400 Motor Rated Voltage 0 to 480 V cfg, VVW 8-32
P401 Motor Rated Current 0.0 to 40.0 A cfg, VVW 8-32
P402 Motor Rated Speed 0 to 24000 rpm cfg, VVW 8-33
P403 Motor Rated Frequency 0 to 400 Hz cfg, VVW 8-33
P404 Motor Rated Power 0 = 0.16 HP (0.12 kW)
1 = 0.25 HP (0.18 kW)
2 = 0.33 HP (0.25 kW)
3 = 0.50 HP (0.37 kW)
4 = 0.75 HP (0.55 kW)
5 = 1.00 HP (0.75 kW)
6 = 1.50 HP (1.10 kW)
7 = 2.00 HP (1.50 kW)
8 = 3.00 HP (2.20 kW)
9 = 4.00 HP (3.00 kW)
10 = 5.00 HP (3.70 kW)
11 = 5.50 HP (4.00 kW)
12 = 6.00 HP (4.50 kW)
13 = 7.50 HP (5.50 kW)
14 = 10.00 HP (7.50 kW)
cfg, VVW 8-33
P405 (*) Encoder Pulses Number 32 to 9999 cfg, VVW 8-33
P407 Motor Rated Power Factor 0.50 to 0.99 cfg, VVW 8-24
P408 Run Self-Tuning 0 = No
1 = Yes
cfg, VVW 8-34
P409 Stator Resistance 0.01 to 99.99 cfg, VVW 8-34
P510 SoftPLC Eng. Unit See options in P209 5-3
P511 SoftPLC Indication Form See options in P210 5-4
Micro Mini Drives | 0-17

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P580 Fire Mode Configuration 0 = Inactive
1 = Active
2 = Active / P134
3 = Reserved
4 = Active / General Disable
cfg 8-16
P582 Fire Mode Auto-reset Adjustable 0 = Limited
1 = Unlimited
cfg 8-16
P588 EOC Maximum Torque 0 to 85 % cfg 8-25
P589 EOC Minimum Voltage 40 to 80 % cfg 8-25
P590 EOC Minimum Frequency 12.0 to 400.0 Hz cfg 8-25
P591 EOC Hysteresis 0 to 30 % cfg 8-25
P613 Main SW Revision -9999 to 9999 ro 6-3
P680 Logical Status 0 to FFFF (hexa)
Bit 0 = Reserved
Bit 1 = Run Command
Bit 2 = Fire Mode
Bit 3 to 4 = Reserved
Bit 5 = 2nd Ramp
Bit 6 = Config. Mode
Bit 7 = Alarm
Bit 8 = Running
Bit 9 = Enabled
Bit 10 = Foward
Bit 11 = JOG
Bit 12 = Remote
Bit 13 = Subvoltage
Bit 14 = Reserved
Bit 15 = Fault
ro 11-6
P681 13-Bit Speed 0 to FFFF (hexa) ro 11-7
P682 Serial/USB Control 0 to FFFF (hexa)
Bit 0 = Ramp Enable
Bit 1 = General Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2nd Ramp
Bit 6 = Reserved
Bit 7 = Fault Reset
Bit 8 to 15 = Reserved
ro 12-1
P683 Serial/USB Speed Ref. 0 to FFFF (hexa) ro 12-1
P684 (*) CO/DN/DP/ETH Control 0 to FFFF (hexa)
Bit 0 = Ramp Enable
Bit 1 = General Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2nd Ramp
Bit 6 = Reserved
Bit 7 = Fault Reset
Bit 8 to 15 = Reserved
ro 12-1
P685 (*) CO/DN/DP/ETH Speed Ref 0 to FFFF (hexa) ro 12-2
P690 Logic State 2 0 to FFFF (hexa)
Bit 0 to 2 = Reserved
Bit 3 = Energy Saver
Bit 4 = Fs Reduction
Bit 5 = Reserved
Bit 6 = Deceleration Ramp
Bit 7 = Acceleration Ramp
Bit 8 = Freeze Ramp
Bit 9 = Setpoint Ok
Bit 10 = DC Link Regulation
Bit 11 = 50Hz Config
Bit 12 = Ride-Through
Bit 13 = Flying Start
Bit 14 = DC Braking
Bit 15 = PWM pulse
ro 11-7
P695 DOx Value 0 to 127 ro 9-24
P696 (*) AOx Value 1 0 to FFFF (hexa) ro 9-9
P697 (*) AOx Value 2 0 to FFFF (hexa) ro 9-9
P700 (*) CAN Protocol 1 = CANopen
2 = DeviceNet
12-4
P701 (*) CAN Address 0 to 127 12-4
0-18 | Micro Mini Drives

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P702 (*) CAN Baud Rate 0 = 1 Mbps/Auto
1 = Reserved/Auto
2 = 500 Kbps
3 = 250 Kbps
4 = 125 Kbps
5 = 100 Kbps/Auto
6 = 50 Kbps/Auto
7 = 20 Kbps/Auto
8 = 10 Kbps/Auto
12-4
P703 (*) Bus Off Reset 0 = Manual
1 = Automatic
12-4
P705 (*) CAN Controller Status 0 = Disabled
1 = Auto-baud
2 = CAN Active
3 = Warning
4 = Error Passive
5 = Bus Off
6 = No Bus Power
ro 12-5
P706 (*) RX CAN Telegrams 0 to 9999 ro 12-5
P707 (*) TX CAN Telegrams 0 to 9999 ro 12-5
P708 (*) Bus Off Counter 0 to 9999 ro 12-5
P709 (*) CAN Lost Messages 0 to 9999 ro 12-5
P710 (*) DeviceNet I/O instances 0 = ODVA Basic 2W
1 = ODVA Extend 2W
2 = Manuf.Spec.2W
3 = Manuf.Spec.3W
4 = Manuf.Spec.4W
5 = Manuf.Spec.5W
6 = Manuf.Spec.6W
12-5
P711 (*) DeviceNet Read Word #3 0 to 1199 12-5
P712 (*) DeviceNet Read Word #4 0 to 1199 12-5
P713 (*) DeviceNet Read Word #5 0 to 1199 12-5
P714 (*) DeviceNet Read Word #6 0 to 1199 12-5
P715 (*) DeviceNet Write Word #3 0 to 1199 12-6
P716 (*) DeviceNet Write Word #4 0 to 1199 12-6
P717 (*) DeviceNet Write Word #5 0 to 1199 12-6
P718 (*) DeviceNet Write Word #6 0 to 1199 12-6
P719 (*) DeviceNet Network Status 0 = Offline
1 = OnLine, Not Conn
2 = OnLine, Connect.
3 = Connection Timed out
4 = Link Failure
5 = Auto-Baud
ro 12-6
P720 (*) DeviceNet Master Status 0 = Run
1 = Idle
ro 12-6
P721 (*) CANopen Comm. Status 0 = Disabled
1 = Reserved
2 = Communic. Enabled
3 = Error Ctrl. Enable
4 = Guarding Error
5 = Heartbeat Error
ro 12-6
P722 (*) CANopen Node Status 0 = Disabled
1 = Initialization
2 = Stopped
3 = Operational
4 = Preoperational
ro 12-6
P740 (*) Profibus Comm. Status 0 = Disabled
1 = Access Error
2 = Offline
3 = Config. Error
4 = Param. Error
5 = Clear Mode
6 = Online
ro 12-7
P742 (*) Profibus Read Word #3 0 to 1199 12-7
P743 (*) Profibus Read Word #4 0 to 1199 12-7
P744 (*) Profibus Read Word #5 0 to 1199 12-7
P745 (*) Profibus Read Word #6 0 to 1199 12-7
P746 (*) Profibus Write Word#3 0 to 1199 12-7
P747 (*) Profibus Write Word#4 0 to 1199 12-7
P748 (*) Profibus Write Word#5 0 to 1199 12-7
Micro Mini Drives | 0-19

0
QUICK REFERENCE OF PARAMETERS
Param. Description Adjustable Range Prop. Page
P749 (*) Profibus Write Word#6 0 to 1199 12-7
P750 (*) Profibus Address 1 to 126 12-7
P751 (*) Profibus Teleg. Sel. 1 = Std. Teleg. 1
2 = Telegram 100
3 = Telegram 101
4 = Telegram 102
5 = Telegram 103
12-7
P754 (*) Profibus Baud Rate 0 = 9.6 kbit/s
1 = 19.2 kbit/s
2 = 93.75 kbit/s
3 = 187.5 kbit/s
4 = 500 kbit/s
5 = Not Detected
6 = 1500 kbit/s
7 = 3000 kbit/s
8 = 6000 kbit/s
9 = 12000 kbit/s
10 = Reserved
11 = 45.45 kbit/s
12-8
P770 (*) Blueooth Device Name 0 to 9999 12-3
P771 (*) Bluetooth Password PIN 0 to 9999 12-4
P840 (*) IR Control Command 0 to FFFF (hexa) ro 9-20
P841 (*) IR Controle Selection 0 = Without Display
1 = With Display
cfg 9-20
P842 (*) Quick View 1 IR 0 to 959 5-4
P843 (*) Quick View 2 IR 0 to 959 5-4
P850 (*) IP Address Config 0 = Parameters
1 = DHCP
cfg 12-8
P851 (*) IP Address 1 0 to 255 cfg 12-8
P852 (*) IP Address 2 0 to 255 cfg 12-8
P853 (*) IP Address 3 0 to 255 cfg 12-8
P854 (*) IP Address 4 0 to 255 cfg 12-8
P855 (*) CIDR Sub-net 1 to 31 cfg 12-8
P856 (*) Gateway 1 0 to 255 cfg 12-8
P857 (*) Gateway 2 0 to 255 cfg 12-8
P858 (*) Gateway 3 0 to 255 cfg 12-9
P859 (*) Gateway 4 0 to 255 cfg 12-9
P860 (*) MBTCP: Communication Status 0 = Disabled
1 = No connection
2 = Connected
3 = Timeout Error
ro 12-9
P863 (*) MBTCP: Active Connections 0 to 4 ro 12-9
P865 (*) MBTCP: TCP Port 0 to 9999 cfg 12-9
P866 (*) MBTCP: Unit ID 0 to 255 cfg 12-9
P868 (*) MBTCP: Timeout 0.0 to 999.9 s cfg 12-9
P869 (*) Master Status EIP 0 = Run
1 = Idle
ro 12-9
P870 (*) EIP Communication Status 0 = Disabled
1 = No connection
2 = Connected
3 = Timeout in I/O Connection
4 = Duplicated IP
ro 12-9
P871 (*) EIP Data Profile 0 = ODVA 20/70: CIP Basic Speed
1 = ODVA 21/71: CIP Enhanced Speed
2 to 3 = Reserved
4 = 20/70: Basic Speed + I/O
5 = 21/71: Enhanced Speed + I/O
6 to 7 = Reserved
8 = 100/150: Speed + I/O
9 to 10 = Reserved
cfg 12-10
P872 (*) Read Word #3 Ethernet 0 to 9999 12-10
P873 (*) Read Word #4 Ethernet 0 to 9999 12-10
P874 (*) Read Word #5 Ethernet 0 to 9999 12-10
P875 (*) Read Word #6 Ethernet 0 to 9999 12-10
P876 (*) Read Word #7 Ethernet 0 to 9999 12-10
P877 (*) Read Word #8 Ethernet 0 to 9999 12-10
P880 (*) Write Word #3 Ethernet 0 to 9999 12-10
0-20 | Micro Mini Drives