WEG CFW-09 User manual

Frequency Inverter
CFW-09
Convertidor de Frecuencia
CFW-09
Inversor de Freqüência
CFW-09
Frequenzumrichter
CFW-09
Variateur de Vitesse
CFW-09
Frequentie-Omzetter
CFW-09
Frekvensomriktare
CFW-09
Преобразователь частоты
CFW-09
User´s Guide
Manual del Usuario
Manual do Usuário
Bedienungsanleitung
Guide d'instalation et d'exploitation
Installatie en gebruikshandleiding
Bruksanvisning
Руководство по эксплуатации
Motors | Automation | Energy | Coatings

FREQUENCY
INVERTER
MANUAL
ATTENTION!
It is very important to check if the
inverter software version is the same
as indicated above.
09/2008
Series:
CFW-09
Software:
version 4.0X
Language:
English
Document:
0899.5306 / 12

Revision
Description
Section
1
FirstEdition.
-
2
Inclusion of the functions Fieldbus and Serial Communication.
Refer to item
8.12 and 8.13
2
Inclusion of the Spare Part List.
Refer to item
7.5
2
DimensionChanging.
Refer to item
3.1.2 and 9.4
3
Inclusion of the PID Regulator.
Refer to
item 6
4
Inclusion of the German Language - Ride-through and Flying
S
tart functions.
Refer to
item 6
4
Inclusion of DBW-01; KIT KME; DC Link Inductor.
Refer to
item 8
5
Inclusion of
I
tem 3.3 - CE Installation.
Refer to
item 3
5
Inclusion of new functions such as Ride-Through for Vector Control, Motor Phase Loss.
Refer to item 6
5
New I/O Expansion Boards EBB.04 and EBB.05.
Refer to item 8
6
General Revision.
-
7
Inclusion of the models from 2.9 to 32 A / 500-600 V.
Refer to items 2.4; 3.1;
3.2.1; 3.3; 4.2; 6.2; 6.3; 7.1;
7.2; 7.4; 7.5; 8.7.1; 8.10.1;
9.1 and 9.1.3
8
Inclusion of new functions:
Refer to item 6
Control Type of the Speed Regulator, Speed Regulator Differential Gain, Stop Mode Selection,
Access to the parameters with different content than default, Hysteresis for Nx/Ny, kWh
Counter, Load User 1 and 2 the factory Hours Hx, via DIx, Parameter Setting Disable via DIx,
Help Message for E24, “P406 = 2 in Vector Control”, Automatic SensorLess Set of P525, Last
10 errors indication, Motor Torque indication via AOx.
8
New optional boards: EBC and PLC1.
Refer to
item 8
8
NewmodelCFW-09SHARKNEMA4X/IP56.
Refer to item 8
8
New models for voltages, currents and powers: Models 500-600 V.
Refer to items 1 to 9
8
Inclusion of the items 8.14 Modbus-RTU, 8.17 CFW-09 Supplied by the DCLink -Line HD,
Refer to item 8
8.18 CFW-09 RB Regenerative Converter.
8
Updating of the Spare Part List.
7
9
Inclusion of new functions:
-
Overcurrent Protection, Default factory reset 50 Hz, Timer Relay, Ramp Holding.
9
New lines of the current and
power supply
.
-
9
PID Regulator to “Academic” Changing.
-
10
General revision and update of the software version (2.6X to 3.1X):
-
Change onthe maximum value of P156 and P401for some models; Change on the maximum
value of P331; Change on the factory default value of P404.
11
New functions;
Incorporation of the Mechanical Brake Logic for cranes, Load Detection Logic and addition of
Refer to items I, 6, 7 and 8
option “Indication of Torque Current Polarity” at the DOx and RLx outputs; VVW Control; DC
Braking for VVW and Sensorless; Flying Start function for the Sensorless Control; support for
EtherNet/IP communication board; read/write function for the PLC board parameters through
Modbus; Indication of the Analog Outputs values in read only parameters P027 to P030;
Simultaneous indication of the speed and current in parameter P070; P313 = 4 (Changes to
LOCAL mode keeping the commands);Regulation of the maximum torque current through
options AI1+AI2 and AI2+AI3; function F > Fx; function ready 2.
12
Updating of the software version to V4.0X.
-
Updating of the parameters P309 and P313.
Addition of new parameters: P335, P336, P337, P338, P340, P341, P342, P343, P344 and P346.
New options for fault Reset.
General revision.
SummaryofRevisions
The table below describes all revisions made to this manual.

Summary
Quick Parameter Reference, Fault and Status Messages
I.
Parameters
.......................................................................................
09
II.
Fault Messages
....................................................................................
33
III.OtherMessages
.................................................................................
34
CHAPTER
1
Safety Notices
1.1 Safety Notices in the Manual
.............................................................
35
1.2 Safety Notices on the Product
...........................................................
35
1.3PreliminaryRecommendations
..........................................................
35
CHAPTER
2
General Information
2.1About this Manual
..............................................................................
37
2.2Software Version
................................................................................
37
2.3About theCFW-09
.............................................................................
37
2.4CFW-09IdentificationLabelandCodeNumber
..................................
39
2.5ReceivingandStorage
.......................................................................
41
CHAPTER
3
Installation and Connection
3.1 Mechanical Installation
......................................................................
42
3.1.1Environment Conditions
...............................................................
42
3.1.2DimensionalofCFW-09
...............................................................
42
3.1.3Mounting Specifications
...............................................................
43
3.1.3.1 Mounting Inside a Panel
.....................................................
44
3.1.3.2Mounting on Surface
..........................................................
45
3.1.3.3Mounting with the Heatsink Through aSurface
..................
46
3.1.4Keypad(HMI)andCoverRemoval
................................................
48
3.2 Electrical Installation
..........................................................................
49
3.2.1Power/GroundingTerminals
.........................................................
49
3.2.2 Locationof thePower/Grounding/ControlConnections
................
51
3.2.3 Rated Voltage Selection
..............................................................
53
3.2.4
Power/GroundingWiringandFuses
............................................
54
3.2.5
PowerConnections
.....................................................................
57
3.2.5.1AC InputConnection
...........................................................
57
3.2.5.2Output Connections
............................................................
58
3.2.5.3GroundingConnections
.......................................................
58
3.2.5.4IT Networks
.........................................................................
59
3.2.6
ControlWiring
..............................................................................
61
3.2.7
TypicalTerminalConnections
......................................................
64
3.3EuropeanEMCDirective-Requirementsfor ConformingInstallations
67
3.3.1Installation
...................................................................................
67
3.3.2 Epcos Filters
...............................................................................
68
3.3.3SchaffnerFilters
...........................................................................
71
3.3.4 EMC Filter Characteristics
...........................................................
74

Summary
CHAPTER
4
Keypad (HMI) Operation
4.1 D
e
scription of the Keypad
..................................................................
86
4.2 Use of the Keypad (HMI)
....................................................................
88
4.2.1
KeypadOperation
........................................................................
88
4.2.2
"Read-Only" Variables and Status
...............................................
89
4.2.3
ParameterViewingandProgramming
.........................................
90
CHAPTER
5
Start-up
5.1
Pre-PowerChecks
............................................................................
93
5.2
InitialPower-up
.................................................................................
93
5.3
Start-up
.............................................................................................
98
5.3.1
Type of Control: V/F 60 Hz- Operation via Keypad (HMI)
............
99
5.3.2Type of Control: Sensorless or Vector with Encoder
(OperationViaKeypad(HMI))
.....................................................
102
5.3.3
Type of Control: VVW - Keypad Operation
.................................
109
CHAPTER
6
Detailed Parameter Description
6.1Access and Read OnlyParameters - P000 to P099
.........................
118
6.2 Regulation Parameters - P100 to P199
.............................................
124
6.3Configuration Parameters -P200 toP399
.........................................
147
6.3.1
Parametersfor CraneApplicationsandforTorqueMaster/Slave
Function - P351 to P368
..........................................................
208
6.4 Motor Parameters - P400 to P499
....................................................
214
6.5 SpecialFunctions Parameters - P500 to P699
.................................
220
6.5.1
PIDRegulator
.............................................................................
220
6.5.2
Description
.................................................................................
220
CHAPTER
7
Diagnostics and Troubleshooting
7.1 Faults and Possible Causes
.............................................................
228
7.2Troubleshooting
................................................................................
233
7.3 Contacting WEG
...............................................................................
235
7.4PreventiveMaintenance
....................................................................
235
7.4.1Cleaning Instructions
..................................................................
236
7.5 Spare Part List
..................................................................................
237
CHAPTER
8
CFW-09 Options and Accessories
8.1 I/O Expansion Boards
.......................................................................
248
8.1.1 EBA(I/O Expansion BoardA)
.....................................................
248

Summary
8.1.2 EBB (I/O Expansion Board B)
....................................................
251
8.1.3 EBE
............................................................................................
254
8.2IncrementalEncoder
.........................................................................
254
8.2.1 EBA/EBB Boards
.......................................................................
254
8.2.2 EBC1 Board
................................................................................
256
8.3 Keypad with LEDs Only
....................................................................
258
8.4 Remote Keypad and Cables
.............................................................
258
8.5Blank Covers
....................................................................................
262
8.6 RS-232 PCCommunication Kit
........................................................
262
8.7 Line Reactor/DC BusChoke
.............................................................
263
8.7.1Application Criteria
......................................................................
264
8.7.2 DC Link Inductor Built in
.............................................................
266
8.8LoadReactor
....................................................................................
267
8.9 RFI Filter
...........................................................................................
267
8.10 Dynamic Braking
............................................................................
268
8.10.1 DB Resistor Sizing
..................................................................
268
8.10.2Installation
...............................................................................
270
8.10.3DynamicBrakingModule-DBW-01andDBW-02
.....................
271
8.10.3.1DBW-01andDBW-02 IdentificationLabel
...................
272
8.10.3.2 Mechanical Installation
................................................
272
8.10.3.3Installation/Connection
................................................
275
8.11
ThroughSurfaceMountingKit
.........................................................
277
8.12
Fieldbus
...........................................................................................
277
8.12.1 Installation of the
Fieldbus
Kit
.................................................
278
8.12.2ProfibusDP
.............................................................................
281
8.12.3 Profibus DP-V1
.......................................................................
283
8.12.4DeviceNet
................................................................................
284
8.12.5DeviceNetDriveProfile
............................................................
286
8.12.6 EtherNet/IP
.............................................................................
287
8.12.7 Use to the Fieldbus/Related Parameters of the CFW-09
.........
294
8.12.7.1VariablesReadfrom theInverter
..................................
294
8.12.7.2 Variables Written inthe Inverter
...................................
296
8.12.7.3 Fault Indications
..........................................................
298
8.12.7.4Addressing of the CFW-09 Variables in the
Fieldbus Devices
.........................................................
299
8.13SerialCommunication
.....................................................................
300
8.13.1Introduction
.............................................................................
300
8.13.2Interfaces Description
..............................................................
301
8.13.2.1RS-485
.........................................................................
301
8.13.2.2RS-232
.........................................................................
302
8.13.3ProtocolDefinitions
.................................................................
302
8.13.3.1UsedTerms
..................................................................
302
8.13.3.2Parameters/Variables Resolution
..................................
303
8.13.3.3CharactersFormat
........................................................
303
8.13.3.4Protocol
........................................................................
303
8.13.3.5
Execution
andTelegram Test
.......................................
305
8.13.3.6Telegram Sequence
......................................................
306
8.13.3.7VariableCode
...............................................................
306
8.13.4Telegram Examples
.................................................................
306
8.13.5Variables and Errorsof the SerialCommunication
..................
307
8.13.5.1 Basic Variables
............................................................
307
8.13.5.2Examples of Telegrams with Basic Variables
...............
310
8.13.5.3Parameters Related tothe SerialCommunication
........
311
8.13.5.4 Errors Relatedto the SerialCommunication
.................
312

Summary
8.13.6Timesfor Read/WriteofTelegrams
..........................................
312
8.13.7 PhysicalConnectionoftheRS-232andRS-485Interface
........
313
8.14
Modbus-RTU
....................................................................................
314
8.14.1 Introductionin theModbus-RTUProtocol
................................
314
8.14.1.1TransmissionModes
....................................................
314
8.14.1.2Message Structure in RTU Mode
..................................
314
8.14.2 Operationof theCFW-09 in theModbus-RTU Network
...........
316
8.14.2.1InterfaceRS-232andRS-485Description
.....................
316
8.14.2.2InverterConfigurationinthe Modbus-RTUNetwork
......
317
8.14.2.3Access to the Inverter Data
...........................................
317
8.14.3Detailed Function Description
...................................................
320
8.14.3.1 Function 01- Read Coils
..............................................
321
8.14.3.2Function 03 -Read HoldingRegister
............................
321
8.14.3.3 Function 05 - Write Single Coil
.....................................
322
8.14.3.4 Function 06 - Write Single Register
..............................
323
8.14.3.5 Function 15 - Write Multiple Coils
.................................
324
8.14.3.6 Function 16 - Write Multiple Registers
.........................
325
8.14.3.7Function43- ReadDeviceIdentification
.......................
326
8.14.4Communication Errors
.............................................................
327
8.14.4.1ErrorMessages
............................................................
327
8.15 KIT KME (for ExtractableMounting)
................................................
329
8.16CFW-09SHARKNEMA4X
.............................................................
330
8.16.1Enclosure Specifications
.........................................................
330
8.16.2Mechanical Installation
............................................................
330
8.16.3 Electrical Installation
...............................................................
332
8.16.4Closingthe
Inverter
..................................................................
332
8.16.5 How to Specify
........................................................................
333
8.17 CFW-09 Supplied bythe DC Link - Line HD
...................................
333
8.18CFW-09RBRegenerativeConverter
...............................................
333
8.19PLC Board
......................................................................................
335
CHAPTER 9
Technical Specification
9.1Power Data
......................................................................................
336
9.1.1
PowerSupplySpecifications
......................................................
336
9.1.2 220-230 V Power Supply
............................................................
337
9.1.3 380-480 V Power Supply
............................................................
337
9.1.4 500-600 V Power Supply
............................................................
338
9.1.5 660-690 V Power Supply
............................................................
340
9.2 Electronics/General Data
..................................................................
343
9.2.1Applicable Standards
..................................................................
344
9.3OptionalDevices
...............................................................................
345
9.3.1 I/O Expansion Board EBA
..........................................................
345
9.3.2 I/O Expansion Board EBB
..........................................................
345
9.4 Mechanical Data
...............................................................................
346

CFW-09-
QUICKPARAMETER REFERENCE
9
QUICK PARAMETER REFERENCE, FAULT AND STATUS MESSAGES
Software:V
4.0X
Application:
CFW-09Model:
SerialNumber:
Responsible:
Date:
/
/
.
I.Parameters
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
P000
Parameter Access
0 to 999
0
-
118
READ ONLYPARAMETERS
P001 to
P099
P001
Speed Reference
0.0 to P134
rpm
118
P002
Motor Speed
0.0 to P134
rpm
118
P003
Motor Current
0.0 to 2600
A (rms)
118
P004
DC Link Voltage
0.0 to 1235
V
119
P005
Motor Frequency
0.0 to 1020
Hz
119
P006
Inverter Status
rdy
-
119
run
Sub
Exy
P007
Motor Voltage
0 to 800
V
119
P009
Motor Torque
0.0 to 150.0
%
119
P010
Output Power
0.0 to
3276
kW
119
P012
Digital Inputs DI1 ... DI8 Status
0 = Inactive (Open)
-
119
1 = Active (Closed)
P013
DigitalandRelayOutputsDO1,DO2,
0 = Inactive (Dropped-out)
-
120
RL1, RL2, and RL3 Status
1 = Active (Picked-up)
P014
Last Fault
0 to 71
-
121
P015
Second Previous Fault
0 to 71
-
121
P016
Third Previous Fault
0 to 71
-
121
P017
Fourth Previous Fault
0 to 71
-
121
P018
Analog Input AI1’ Value
-100 to +100
%
121
P019
Analog Input AI2’ Value
-100 to +100
%
121
P020
Analog Input AI3’ Value
-100 to +100
%
121
P021
Analog Input AI4’ Value
-100 to +100
%
121
P022
WEGUse
-
-
121
P023
Software Version
V4.0X
-
121
P024
A/D Conversion Value of AI4
-32768 to +32767
-
121
P025
A/D Conversion Value of Iv
0 to 1023
-
121
P026
A/D Conversion Value of Iw
0 to 1023
-
121
P027
AO1 Value
0.0 to 100
%
122
P028
AO2 Value
0.0 to 100
%
122
P029
AO3 Value
-100 to +100
%
122
P030
AO4 Value
-100 to +100
%
122
P040
PID Process Variable
0 to 100
%
122
P042
Powered Time
0 to 65535
h
122
P043
EnabledTime
0 to 6553.5
h
122
P044
kWhCounter
0 to 65535
kWh
123

CFW-09-
QUICKPARAMETER REFERENCE
10
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
(*)
P136 has different functions for V/F and Vector Control.
P060
Fifth Error
0 to 71
-
123
P061
Sixth Error
0 to 71
-
123
P062
Seventh Error
0 to 71
-
123
P063
EighthError
0 to 71
-
123
P064
Ninth Error
0 to 71
-
123
P065
Tenth Error
0 to 71
-
123
P070
Motor Current and Motor Speed
0 to 2600
A (rms)
123
0 to P134
rpm
P071
CommandWord
0 a 65535
-
123
P072
Fieldbus Speed Reference
0 a 65535
-
123
REGULATIONPARAMETERS
P100 to P199
Ramps
P100
Acceleration Time
0.0 to 999
20.0
s
124
P101
DecelerationTime
0.0 to 999
20.0
s
124
P102
Acceleration Time 2
0.0 to 999
20.0
s
124
P103
Deceleration Time 2
0.0 to 999
20.0
s
124
P104
SRamp
0 = Inactive (Linear)
0 = Inactive
-
124
1 = 50 %
2 = 100 %
Speed References
P120
Speed Reference Backup
0 = Inactive
1 = Active
-
124
1 = Active
P121
Keypad Speed Reference
P133 to P134
90
rpm
125
P122
(2)(11)
JOG or JOG+ Speed Reference
00 to P134
150 (125)
rpm
125
P123
(2)(11)
JOG- Speed Reference
00 to P134
150 (125)
rpm
125
P124
(2)(11)
Multispeed Reference 1
P133 to P134
90 (75)
rpm
126
P125
(2)(11)
Multispeed Reference 2
P133 to P134
300 (250)
rpm
126
P126
(2)(11)
Multispeed Reference 3
P133 to P134
600 (500)
rpm
126
P127
(2)(11)
Multispeed Reference 4
P133 to P134
900 (750)
rpm
126
P128
(2)(11)
Multispeed Reference 5
P133 to P134
1200 (1000)
rpm
126
P129
(2)(11)
Multispeed Reference 6
P133 to P134
1500 (1250)
rpm
126
P130
(2)(11)
Multispeed Reference 7
P133 to P134
1800 (1500)
rpm
126
P131
(2)(11)
Multispeed Reference 8
P133 to P134
1650 (1375)
rpm
126
Speed Limits
P132
(1)
Maximum Overspeed Level
(0 to 99) x P134
10
%
127
100 = Disabled
P133
(2)(11)
Minimum Speed Reference
0 to (P134-1)
90 (75)
rpm
127
P134
(2)(11)
Maximum Speed Reference
(P133+1) to (3.4 x P402)
1800 (1500)
rpm
127
I/F Control
P135
(2)
Speed transition to I/F Control
0 to 90
18
rpm
128
P136
(*)
Current Reference (I*)
0 = I
mr
1 = 1.11 x I
mr
-
128
for I/F Control
1 = 1.11 x I
mr
2 = 1.22 x I
mr
3 = 1.33 x I
mr
4 = 1.44 x I
mr
5 = 1.55 x I
mr
6 = 1.66 x I
mr
7 = 1.77 x I
mr
8 = 1.88 x I
mr
9 = 2.00 x I
mr

CFW-09-
QUICKPARAMETER REFERENCE
11
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
(*)
P151 has different function for V/F or Vector Control.
V/F Control
P136
(*)
Manual Boost Torque
0 to 9
1
-
129
P137
Autommatic Torque Boost
0.00 to 1.00
0.00
-
130
P138
SlipCompensation
-10.0 to +10.0
0.0
%
130
P139
Output Current Filter
0.00 to 16.00
1.00
s
131
P140
Dwell Time at Start
0.0 to 10.0
0.0
s
131
P141
Dwell Speed at Start
0 to 300
90
rpm
131
Adjustable V/F
P142
(1)
Maximum Output Voltage
0.0 to 100.0
100.0
%
132
P143
(1)
Intermediate Output Voltage
0.0 to 100.0
50.0
%
132
P144
(1)
Output Voltage at 3 Hz
0.0 to 100.0
8.0
%
132
P145
(1)
FieldWeakeningSpeed
P133 (> 90) to P134
1800
rpm
132
P146
(1)
IntermediateSpeed
90 to P145
900
rpm
132
DC Link Voltage Regulation
P150
(1)
DC LinkVoltage Regulation Mode
0 = With Losses
1 = Without Losses
-
133
1 = Without Losses
2= Enable/Disable
viaDI3...DI8
P151
(6) (*)
DC Link Voltage Regulation Level
339 to 400 (P296 = 0)
400
V
133 and
(V/F Control / Vector Control
585 to 800 (P296 = 1)
800
136
with optimal braking)
616 to 800 (P296 = 2)
800
678 to 800 (P296 = 3)
800
739 to 800 (P296 = 4)
800
809 to 1000 (P296 = 5)
1000
885 to 1000 (P296 = 6)
1000
924 to 1000 (P296 = 7)
1000
1063 to 1200 (P296 = 8)
1200
P152
Proportional Gain
0.00 to 9.99
0.00
-
137
P153
(6)
Dynamic Braking Level
339 to 400 (P296 = 0)
375
V
137
585 to 800 (P296 = 1)
618
616 to 800 (P296 = 2)
675
678 to 800 (P296 = 3)
748
739 to 800 (P296 = 4)
780
809 to 1000 (P296 = 5)
893
885 to 1000 (P296 = 6)
972
924 to 1000 (P296 = 7)
972
1063 to 1200 (P296 = 8)
1174
P154
Dynamic Braking Resistor
0.0 to 500
0.0

138
P155
DB Resistor Power Rating
0.00 to 650
2.60
kW
138
Overload Currents
P156
(2) (7) (12)
Overload Current 100 % Speed
P157 to 1.3 x P295
1.1 x P401
A
139
P157
(2) (7)
Overload Current 50 % Speed
P156to P158
0.9 x P401
A
139
P158
(2) (7)
Overload Current 5 % Speed
(0.2 x P295) to P157
0.55 x P401
A
139
Speed Regulator
P160
(1)
Optimization of the
0= Normal
0= Normal
-
140
Speed Regulator
1 = Saturated
P161
(3)
Proportional Gain
0.0 to 63.9
7.4
-
142
P162
(3)
Integral Gain
0.000 to 9.999
0.023
-
142
P163
Local Speed Reference Offset
-999 to +999
0
-
143
P164
Remote Speed Reference Offset
-999 to +999
0
-
143

CFW-09-
QUICKPARAMETER REFERENCE
12
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
P165
SpeedFilter
0.012 to 1.000
0.012
s
143
P166
Speed Regulator Differential Gain
0.00 to 7.99
0.00 (without
-
143
differential action)
Current Regulator
P167
(4)
Proportional Gain
0.00 to 1.99
0.50
-
143
P168
(4)
Integral Gain
0.000 to 1.999
0.010
-
143
P169
(*) (7)
MaximumOutputCurrent(V/FControl)
(0.2 x P295) to
(1.8 x P295)
1.5 x P295
A
144
P169
(*) (7)
Maximum Forward Torque Current
0 to 180
125
%
144
(Vector Control)
P170
Maximum Reverse Torque Current
0 to 180
125
%
144
(Vector Control)
P171
Maximum Forward Torque Current at
0 to 180
125
%
145
Maximum Speed (P134)
P172
Maximum Reverse Torque Current at
0 to 180
125
%
145
Maximum Speed (P134)
P173
Curve Type of the Max. Torque
0= Ramp
0= Ramp
-
145
1 = Step
Flux Regulator
P175
(5)
Proportional Gain
0.0 to 31.9
2.0
-
146
P176
(5)
Integral Gain
0.000 to 9.999
0.020
-
146
P177
MinimumFlux
0 to 120
0
%
146
P178
NominalFlux
0 to 120
100
%
146
P179
MaximumFlux
0 to 120
120
%
146
P180
FieldWeakenig Start Point
0 to 120
95
%
146
P181
(1)
Magnetization Mode
0 = General Enable
0 = General Enable
-
146
1 = Start/Stop
CONFIGURATIONPARAMETERS
P200 to P399
Generic Parameters
P200
Password
0 = Off
1 = On
-
147
1 = On
P201
(11)
Language Selection
0 = Português
0, 1, 2, 3
(11)
-
147
1 = English
2 = Español
3 = Deutsch
P202
(1) (2) (11)
Type of Control
0 = V/F 60 Hz
0 (1)
-
147
1 = V/F 50 Hz
2 = V/F Adjustable
3 = Sensorless Vector
4 = Vector with Encoder
5 = VVW (Voltage Vector WEG)
P203
(1)
Special Function Selection
0 = None
0 = None
-
147
1= PIDRegulator
P204
(1)(10)
Load/Save Parameters
0 = Not Used
0 = Not Used
-
148
1 = Not Used
2 = Not Used
3 = Reset P043
4 = Reset P044
5 = Loads Factory Default-60 Hz
6 = Loads Factory Default-50 Hz
(*)
P169 has different function for V/F or Vector Control.

CFW-09-
QUICKPARAMETER REFERENCE
13

Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting

7 = Loads User Default 1
8 = Loads User Default 2
9 = Not Used
10 = Save User Default 1
11 = Save User Default 2
P205
Display Default Selection
0
=
P005 (Motor Frequency)
2 = P002
-
149
1 = P003 (Motor Current)
2 = P002 (Motor Speed)
3 = P007 (Motor Voltage)
4 = P006 (Inverter Status)
5 = P009 (Motor Torque)
6 = P070
(Motor Speed and
Motor Current)
7 = P040
(PID Process
Variable)
P206
Auto-Reset Time
0 to 255
0
s
150
P207
Reference Engineering Unit 1
32 to 127 (ASCII)
114 = r
-
150
A, B, ... , Y, Z
0, 1, ... , 9
#, $, %, (, ), *, +, ...
P208
(2)(11)
Reference Scale Factor
1 to 18000
1800 (1500)
-
150
P209
(1)
Motor Phase Loss Detection
0 = Off
0 = Off
-
151
1 = On
P210
Decimal Point of theSpeed Indication
0 to 3
0
-
151
P211
(1)
Zero Speed Disable
0 = Off
0 = Off
-
151
1 = On
P212
Condition to Leave Zero
0 = N* or N>P291
0 = N* or N>P291
-
152
SpeedDisable
1= N*>P291
P213
Time Delay for Zero Speed Disable
0 to 999
0
s
152
P214
(1) (9)
Line Phase Loss Detection
0 = Off
1 = On
-
152
1 = On
P215
(1)
Keypad Copy Function
0 = Off
0 = Off
-
152
1 = Inverter Keypad
2 = Keypad Inverter
P216
Reference Engineering Unit 2
32 to 127 (ASCII)
112 = p
-
154
A, B, ... , Y, Z
0, 1, ... , 9
#, $, %, (, ), *, +, ...
P217
Reference Engineering Unit 3
32 to 127 (ACSII)
109 = m
-
154
A, B, ... , Y, Z
0, 1, ... , 9
#, $, %, (, ), *, +, ...
P218
LCD Display Contrast
0 to 150
127
-
154
Adjustment
Local/Remote Definition
P220
(1)
Local/Remote Selection Source
0 = Always Local
2 = Keypad
-
154
1 = Always Remote
(Default Local)
2 = Keypad (Default Local)
3 = Keypad (
Default Remote
)

CFW-09-
QUICKPARAMETER REFERENCE
14
4 = DI2 to DI8
5 = Serial (L)
6 = Serial (R)
7 = Fieldbus (L)
8 = Fieldbus (R)
9 = PLC (L)
10 = PLC (R)
P221
(1)
Local Speed Reference Selection
0 = keypad
0 = Keypad
-
155
1 =AI1
2 =AI2
3 =AI3
4 =AI4
5 = Add AI > 0
6 = Add AI
7=E.P.
8 = Multispeed
9 = Serial
10 = Fieldbus
11= PLC
P222
(1)
Remote Speed Reference
0 = keypad
1 =AI1
-
155
Selection
1 =AI1
2 =AI2
3 =AI3
4 =AI4
5 = Add AI > 0
6 = Add AI
7= E.P.
8 = Multispeed
9 = Serial
10 = Fieldbus
11= PLC
P223
(1) (8)
LocalFWD/REV Selection
0 = Always Forward
2 = Keypad
-
156
1 = Always Reverse
(Default FWD)
2 = Keypad (Default FWD)
3 = Keypad (Default REV)
4= DI2
5 = Serial (Default FWD)
6 = Serial (Default REV)
7 = Fieldbus (Default FWD)
8 = Fieldbus (Default REV)
9 = PolarityAI4
10= PLC(FWD)
11 = PLC (REV)
P224
(1)
Local Start/Stop Selection
0 = [I] and [O] Keys
0 = [I] and [O] Keys
-
156
1 = DIx
2 = Serial
3 = Fieldbus
4=PLC
P225
(1) (8)
Local JOG Selection
0 = Disable
1 = Keypad
-
156
1 = Keypad
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting

CFW-09-
QUICKPARAMETER REFERENCE
15
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
2 = DI3 to DI8
3 = Serial
4 = Fieldbus
5=PLC
P226
(1) (8)
RemoteFWD/REVSelection
0 = Always Forward
4= DI2
-
157
1 = Always Reverse
2 = Keypad (Default FWD)
3 = Keypad (Default REV)
4= DI2
5 = Serial (Default FWD)
6 = Serial (Default REV)
7 = Fieldbus (Default FWD)
8 = Fieldbus (Default REV)
9 = PolarityAI4
10= PLC(FWD)
11 = PLC (REV)
P227
(1)
RemoteStart/StopSelection
0 = [I] and [O] Keys
1 = DIx
-
157
1 = DIx
2 = Serial
3 = Fieldbus
4=PLC
P228
(1) (8)
RemoteJOGSelection
0 = Disable
2 = DI3 to DI8
-
157
1 = Keypad
2 = DI3 to DI8
3 = Serial
4 = Fieldbus
5=PLC
Stop Model Definition
P232
(1)
Stop Mode Selection
0 =
Ramp to Stop
0 = Ramp to Stop
-
163
1 = Coast to Stop
2 =
Fast Stop
Analog Inputs
P233
Analog Inputs Dead Zone
0 = Off
0 = Off
-
163
1 = On
P234
Analog InputAI1 Gain
0.000 to 9.999
1.000
-
164
P235
(1)
Analog InputAI1 Signal
0 = (0 to 10) V / (0 to 20) mA
0 = (0 to 10) V /
-
165
1 = (4 to 20) mA
(0 to 20) mA
2 = (10 to 0) V / (20 to 0) mA
3 = (20 to 4) mA
P236
Analog Input AI1 Offset
-100.0 to +100.0
0.0
%
165
P237
(1) (8)
Analog InputAI2 Function
0= P221/P222
0= P221/P222
-
165
1 = N* without ramp
2=MaximumTorqueCurrent
3 = PID Process Variable
4=MaximumTorqueCurrent
(AI2 + AI1)
P238
Analog InputAI2 Gain
0.000 to 9.999
1.000
-
166

CFW-09-
QUICKPARAMETER REFERENCE
16
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
P239
(1)
Analog InputAI2 Signal
0 = (0 to 10) V / (0 to 20) mA
0 = (0 to 10) V /
-
166
1 = (4 to 20) mA
(0 to 20) mA
2 = (10 to 0) V / (20 to 0) mA
3 = (20 to 4) mA
P240
Analog Input AI2 Offset
-100.0 to +100.0
0.0
%
167
P241
(1) (8)
Analog InputAI3 Function
0= P221/P222
0= P221/P222
-
167
(Requires Optional I/O Expansion
1 = Without ramp
Board EBB)
2 =
MaximumTorqueCurrent
3 = PID Process Variable
4=MaximumTorqueCurrent
(AI3 + AI2)
P242
Analog InputAI3 Gain
0.000 to 9.999
1.000
-
168
P243
(1)
Analog InputAI3 Signal
0 = (0 to 10) V / (0 to 20) mA
0 = (0 to 10) V /
-
168
1 = (4 to 20) mA
(0 to 20) mA
2 = (10 to 0) V / (20 to 0) mA
3 = (20 to 4) mA
P244
Analog Input AI3 Offset
-100.0 to +100.0
0.0
%
168
P245
Analog InputAI4 Gain
0.000 to 9.999
1.000
-
168
P246
(1)
Analog InputAI4 Signal
0 = (0 to 10) V / (0 to 20) mA
0 = (0 to 10) V /
-
168
(Requires Optional I/O Expansion
1 = (4 to 20) mA
(0 to 20) mA
Board EBA)
2 = (10 to 0) V / (20 to 0) mA
3 = (20 to 4) mA
4 = (-10 to +10) V
P247
Analog Input AI4 Offset
-100.0 to +100.0
0.0
%
169
P248
InputFilterAI2
0.0 to 16.0
0.0
s
169
Analog Outputs
P251
Analog Output AO1 Function
0 = Speed Reference
2 = Real Speed
-
169
(CC9 or EBB board)
1 = Total Reference
2 = Real Speed
3 = Torque Current
Reference (Vector)
4
=
Torque Current (Vector)
5 = Output Current
6 = PID Process Variable
7 = Active Current (V/F)
8 = Power (kW)
9= PIDSetpoint
10
=
Positive Torque Current
11 = Motor Torque
12= PLC
13 =
Dead Zone for
SpeedIndication
14 = Motor Voltage
P252
Analog Output AO1 Gain
0.000 to 9.999
1.000
-
169
P253
Analog Output AO2 Function
0 = Speed Reference
5 = Output Current
-
169
(CC9 or EBB board)
1 = Total Reference
2 = Real Speed
3 = Torque Current
Reference (Vector)

CFW-09-
QUICKPARAMETER REFERENCE
17
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
4 = Torque Current (Vector)
5 = Output Current
6 = PID Process Variable
7 = Active Current (V/F)
8 = Power (kW)
9= PIDSetpoint
10
=
Positive Torque Current
11 = Motor Torque
12= PLC
13 = Dead Zone for
SpeedIndication
14 = Motor Voltage
P254
Analog Output AO2 Gain
0.000 to 9.999
1.000
-
169
P255
Analog Output AO3 Function
0 = Speed Reference
2 = Real Speed
-
169
(Requires Optional I/O Expansion
1 = Total Reference
Board EBA)
2 = Real Speed
3 = Torque Current
Reference (Vector)
4
=
Torque Current (Vector)
5 = Output Current
6 = PID Process Variable
7 = Active Current (V/F)
8 = Power (kW)
9= PIDSetpoint
10
=PositiveTorqueCurrent
11 = Motor Torque
12= PLC
13 =
Not Used
14 = Motor Voltage
15 to63= Exclusive WEGuse
P256
Analog Output AO3 Gain
0.000 to 9.999
1.000
-
170
P257
Analog Output AO4 Function
0 = Speed Reference
5 = Output Current
-
170
(Requires optional I/O Expansion
1 = Total Reference
Board EBA)
2 = Real Speed
3 = Torque Current
Reference (Vector)
4 = Torque Current (Vector)
5 = Output Current
6 = PID Process Variable
7 = Active Current (V/F)
8 = Power (kW)
9= PIDSetpoint
10
=
Positive Torque Current
11 = Motor Torque
12= PLC
13 = Not Used
14 = Motor Voltage
15 to63= Exclusive WEGuse
P258
Analog Output AO4 Gain
0.000 to 9.999
1.000
-
170
P259
Dead Zone for Speed Indication
0 to P134
1000
rpm
171

CFW-09-
QUICKPARAMETER REFERENCE
18
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
Digital Inputs
P263
(1)
Digital Input DI1Function
0 = Not Used
1 = Start/Stop
-
172
1 = Start/Stop
2 = General Enable
3 = Fast Stop
P264
(1)
Digital Input DI2Function
0=FWD/REV
0=FWD/REV
-
172
1 = Local/Remote
2 = Not Used
3 = Not Used
4 = Not Used
5 = Not Used
6 = Not Used
7 = Not Used
8 = Reverse Run
P265
(1) (8)
Digital Input DI3Function
0 = Not Used
0 = Not Used
-
172
1 = Local/ Remote
2 = General Enable
3 = JOG
4 = No External Fault
5 = Increase E.P.
6 = Ramp 2
7 = Not Used
8 = Forward Run
9 = Speed/Torque
10 = JOG+
11 = JOG-
12 = Reset
13 = Fieldbus
14 = Start (3 wire)
15 = Man/Auto
16 = Not used
17 = Disables Flying Start
18 = DC Voltage Regulator
19 = Parameter Setting
Disable
20 = Load user
21 = Timer (RL2)
22 = Timer (RL3)
P266
(1)
Digital Input DI4Function
0 = Not used
0 = Not Used
-
172
1 = Local/ Remote
2 = General Enable
3 = JOG
4 = No external Fault
5 = Decrease E.P.
6 = Ramp 2
7 = Multispeed (MS0)
8 = Reverse Run
9 = Speed/Torque
10 = JOG+

CFW-09-
QUICKPARAMETER REFERENCE
19
11 = JOG-
12 = Reset
13 = Fieldbus
14 = Stop (3 wire)
15 = Man/Auto
16 = Not used
17 = Disables Flying Start
18 = DC voltage regulator
19 = Parameter Setting
Disable
20 = Load User
21 = Timer (RL2)
22 = Timer (RL3)
P267
(1)
Digital Input DI5Function
0 = Not Used
3 = JOG
-
172
1 = Local/ Remote
2 = General Enable
3 = JOG
4 = No External Fault
5 = Increase E.P.
6 = Ramp 2
7 = Multispeed (MS1)
8 = Fast Stop
9 = Speed/Torque
10 = JOG+
11 = JOG-
12 = Reset
13 = Fieldbus
14 = Start (3 wire)
15 = Man/Auto
16 = Not Used
17 = Disables Flying Start
18 = DC Voltage Regulator
19 = Parameter Setting
Disable
20 = Load User
21 = Timer (RL2)
22 = Timer (RL3)
P268
(1)
Digital Input DI6Function
0 = Not Used
6 = Ramp 2
-
173
1 = Local/ Remote
2 = General Enable
3 = JOG
4 = No External Fault
5 = Decrease E.P.
6 = Ramp 2
7 = Multispeed (MS2)
8 = Fast Stop
9 = Speed/Torque
10 = JOG+
11 = JOG-
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting

CFW-09-
QUICKPARAMETER REFERENCE
20
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
12 = Reset
13 = Fieldbus
14 = Stop (3 wire)
15 = Man/Auto
16 = Not Used
17 = Disables Flying Start
18 = DC voltage regulator
19 = Parameter setting
disable
20 = Load user
21 = Timer (RL2)
22 = Timer (RL3)
P269
(1)
Digital Input DI7Function
0 = Not Used
0 = Not used
-
173
(Requires optional I/O
1 = Local/ Remote
expansion board EBA or EBB)
2 = General Enable
3 = JOG
4 = No External Fault
5 = Not Used
6 = Ramp 2
7 = Not Used
8 = Fast Stop
9 = Speed/Torque
10 = JOG+
11 = JOG-
12 = Reset
13 = Fieldbus
14 = Start (3 wire)
15 = Man/Auto
16 = Not Used
17 = Disables Flying Start
18 = DC Voltage Regulator
19 = Parameter Setting
Disable
20 = Load User
21 = Timer (RL2)
22 = Timer (RL3)
P270
(1)
Digital Input DI8Function
0 = Not used
0 = Not used
-
173
(Requires optional I/O
1 = Local/Remote
expansion board EBA or EBB)
2 = General Enable
3 = JOG
4 = No External Fault
5 = Not Used
6 = Ramp 2
7 = Not Used
8 = Fast Stop
9 = Speed/Torque
10 = JOG+
11 = JOG-
12 = Reset

CFW-09-
QUICKPARAMETER REFERENCE
21
Parameters
Function
Adjustable Range
Factory
Unit
User's
Page
Setting
Setting
13 = Fieldbus
14 = Stop (3 wire)
15 = Man/Auto
16 = Motor Thermistor
17 = Disables Flying Start
18 = DC Voltage Regulator
19 = Parameter Setting
Disable
20 = Not Used
21 = Timer (RL2)
22 = Timer (RL3)
Digital Outputs
P275
(1)
DigitalOuput DO1Function
0 = Not used
0 = Not Used
-
180
(requires optional I/O
1 = N* > Nx
expansion board EBA or EBB)
2 = N > Nx
3 = N < Ny
4 = N = N*
5 = Zero Speed
6 = Is > Ix
7 = Is < Ix
8 = Torque > Tx
9 = Torque < Tx
10= Remote
11 = Run
12 = Ready
13 = No Fault
14 = No E00
15=NoE01+E02+E03
16 = No E04
17 = No E05
18 = (4 to 20) mA OK
19 = Fieldbus
20= FWD
21 = Proc.Var. > VPx
22 = Proc. Var. < VPy
23 = Ride-Through
24 = Pre-charge OK
25 = Fault
26 = Enabled Hours > Hx
27 = Not Used
28 = Not Used
29 = N > Nx and Nt > Nx
30 = Brake (Actual Speed)
31 =
Brake (Total Reference)
32 = Overweight
33 = Slack Cable
34 = Torque Polarity +/-