WEG CFW-11 Series User manual

Frequency Inverter
Convertidor de Frecuencia
Inversor de Frequência
CFW-11 Sizes/Mec. A...D
Addendum to the CFW-11 User’s Manual -
New Information
Adendo al Manual del Usuario CFW-11 -
Nuevas Informaciones
Adendo ao Manual do Usuário CFW-11 -
Novas Informações
English / Español / Português
Motors | Automation | Energy | Transmission & Distribution | Coatings

Summary / Índice
SUMMARY
1 INTRODUCTION .................................................................................................5
2 INFORMATION ON CFW-11 INVERTERS WITH SERIAL NUMBER
STARTING AT 1011361739 AND FIRMWARE VERSION V3.00 OR HIGHER ...5
2.1 On firmware version V3.00 ....................................................................................5
2.2 Modifications on Slot 5 (FLASH Memory Module) .............................................6
2.3 Modifications on Slot 4 (Anybus-CC Communication Modules) ......................7
3 GENERAL INFORMATION ................................................................................7
3.1 Accessories ............................................................................................................7
3.2 HMI Installation at the Cabinet Door or Command Panel (Remote HMI) .........9
3.3 Additional Information about the HMI Battery .................................................10
ÍNDICE
1 INTRODUCCIÓN ..............................................................................................12
2 INFORMACIONES PARA CONVERTIDORES CFW-11 CON NÚMERO
DE SERIE A PARTIR DE 1011361739 Y VERSIÓN DE SOFTWARE V3.00 O
SUPERIOR ............................................................................................................... 12
2.1 Sobre la Versión de Software V3.00 o Superior ...............................................12
2.2 Modificaciones en el Slot 5 (Módulo de Memoria FLASH) ..............................13
2.3 Modificaciones en el Slot 4 (Módulos de Comunicación Anybus-CC) ..........14
3 INFORMACIONES GENERALES ...................................................................14
3.1 Accesorios ...........................................................................................................14
3.2 Montaje de la HMI en la Puerta del Tablero/Armário o en la Mesa de
Comando (HMI Remota) ...........................................................................................17
3.3 Informaciones Adicionales a Respecto de la Batería de la HMI .....................17
ÍNDICE
1 INTRODUÇÃO ..................................................................................................20
2 INFORMAÇÕES PARA INVERSORES CFW-11 COM NÚMERO DE SÉRIE A
PARTIR DE 1011361739 E VERSÃO DE SOFTWARE V3.00 OU SUPERIOR .. 20
2.1 Sobre a Versão de Software V3.00 ou Superior ...............................................20
2.2 Modificações no Slot 5 (Módulo de Memória FLASH) .....................................21
2.3 Modificações no Slot 4 (Módulos de Comunicação Anybus-CC) ..................22
3 INFORMAÇÕES GERAIS ...............................................................................22
3.1 Acessórios ............................................................................................................22
3.2 Montagem da HMI na Porta do Painel ou Mesa de Comando (HMI Remota) .25
3.3 Informações Adicionais Sobre a Bateria da HMI .............................................25

CFW-11 | 5
- English -
Addendum to the CFW-11 User's Manual
1 INTRODUCTION
This addendum provides additional information on CFW-11 inverters in general
and some specific information on CFW-11 inverters with serial number starting
at 1011361739 and firmware version V3.00. On those inverters the control board
revision is “C” (CC11C).
ATTENTION!
Operation of this equipment requires detailed installation and operation
instructions provided in the User's Manual, Software Manual and Manual/
Guides for Kits and Accessories. Only User's Manual is provided on a
printed version. The other manuals are provided on the CD supplied with
the product. This CD should be retained with this equipment at all times.
A hard copy of this information may be ordered through your local WEG
representative.
ATTENTION!
Integral solid state short circuit protection does not provide branch circuit
protection. Branch circuit protection must be provided in accordance with
applicable local codes.
2 INFORMATION ON CFW-11 INVERTERS WITH SERIAL NUMBER
STARTING AT 1011361739 AND FIRMWARE VERSION V3.00 OR
HIGHER
2.1 On firmware version V3.00
ATTENTION!
Firmware version V3.00 or higher cannot be used on inverters with
serial number under 1011361739, that use a control board with revision
prior to “C”.
Any firmware version prior to V3.00 cannot be used on inverters with
control board revision “C” or higher.
Further information on the new features and corrections of firmware version V3.00
is provided in a specific addendum to the programming manual (available only on
the CD).

6 | CFW-11 - English -
Addendum to the CFW-11 User's Manual
2.2 Modifications on Slot 5 (FLASH Memory Module)
To avoid connection failures and to improve the ease of connection to the inverter,
the FLASH memory module (MMF) was modified from MMF-01 to MMF-03. The
following picture shows the differences between MMF-01 and MMF-03 modules
and the ones implemented on the inverter.
The MMF-03 module is incompatible with the older MMF-01 and can only be used
on inverters with serial number starting at 1011361739 that have revision “C” of the
control board.
(a) MMF-01
(b) MMF-03
Figure 2.1 (a) and (b): Differences between MMF-01 and MMF-03 modules
On the MMF-03 module there is an area reserved to user annotations. (e.g.: writing
the SoftPLC application version).

CFW-11 | 7
- English -
Addendum to the CFW-11 User's Manual
2.3 Modifications on Slot 4 (Anybus-CC Communication Modules)
In order to ensure the proper connection of Anybus-CC communication accessory
in Slot 4, a support with guide rails was included in the product according to the
following picture.
Support with
guide rails
Figure 2.2: Anybus-CC accessory connection
3 GENERAL INFORMATION
3.1 Accessories
New accessories were developed for CFW-11 inverter series, that correct (WEG part
number) and complement table 7.2 of user’s manual as follows:
Accessory models
WEG Part
Number Name Description Slot
Identification
Parameters
P0027 P0028
Control accessories for installation in the Slots 1, 2 and 3
11008162 IOA-01 IOA module: 1 voltage/current analog input (14 bits);
2 digital inputs; 2 voltage/current analog outputs (14
bits); 2 open-collector digital outputs.
1 FD-- ----
11008099 IOB-01 IOB module: 2 isolated analog inputs (voltage/current);
2 digital inputs; 2 isolated analog outputs (voltage/
current) (the programming of the outputs is identical
as in the standard CFW-11); 2 open-collector digital
outputs.
1 FA-- ----
11008100 ENC-01 5 to 12 Vdc incremental encoder module, 100 kHz,
with an encoder signal repeater.
2 --C2 ----
11008101 ENC-02 5 to 12 Vdc incremental encoder module, 100 kHz. 2 --C2 ----
11008102 RS485-01 RS-485 serial communication module (Modbus). 3 ---- CE--
11008103 RS232-01 RS-232C serial communication module (Modbus). 3 ---- CC--

8 | CFW-11 - English -
Addendum to the CFW-11 User's Manual
WEG Part
Number Name Description Slot
Identification
Parameters
P0027 P0028
11008104 RS232-02 RS-232C serial communication module with DIP-switches
for programming the microcontroller FLASH memory.
3 ---- CC--
11008105 CAN/RS485-01 CAN and RS-485 interface module (CANopen /
DeviceNet / Modbus).
3 ---- CA--
11008106 CAN-01 CAN interface module (CANopen / DeviceNet). 3 ---- CD--
11008911 PLC11-01 PLC module. 1, 2
and 3
---- --xx(1)(3)
11094251 PLC11-02 PLC module. 1, 2
and 3
---- --xx(1)(3)
11126732 IOE-01 Input module with 5 PTC type sensors. 1 25-- ----
11126735 IOE-02 Input module with 5 PT100 type sensors. 1 23-- ----
11126750 IOE-03 Input module with 5 KTY84 type sensors. 1 27-- ----
11126674 IOC-01 IOC module with 8 digital inputs and 4 relay outputs
(use with SoftPLC).
1 C1 ----
11126730 IOC-02 IOC module with 8 digital inputs and 8 NPN open
collector digital outputs (use with SoftPLC).
1 C5 ----
11045488 PROFIBUS DP-01 Profibus DP communication module. 3 ---- C9--
Anybus-CC accessories for installation in the Slot 4
11008107 PROFIBUSDP-05 Profibus DP interface module. 4 ---- --xx(2)(3)
11008158 DEVICENET-05 DeviceNet interface module. 4 ---- --xx(2)(3)
10933688 ETHERNET/IP-05 Ethernet/IP interface module. 4 ---- --xx(2)(3)
11008160 RS232-05 RS-232 (passive) interface module (Modbus). 4 ---- --xx(2)(3)
11008161 RS485-05 RS-485 (passive) interface module (Modbus). 4 ---- --xx(2)(3)
11550476 MODBUSTCP-05 Modbus TCP interface module. 4 ---- --xx(2)(3)
11550548 PROFINETIP-05 PROFINET IO interface module. 4 ---- --xx(2)(3)
FLASH Memory Module for installation in the Slot 5 – Factory Settings Included
10413633 MMF-01 FLASH memory module – old. 5 ---- --xx(3)
11719952 MMF-03 FLASH memory module – new. 5 ---- --xx(3)
HMI avulsa, tampa cega e moldura para HMI externa
11008913 HMI-01 Stand-alone HMI.(4) HMI - -
11010521 RHMIF-01 Remote HMI frame kit (IP56). - - -
10950192 1 m HMI Cable 1 m serial remote keypad cable set. - - -
10951226 2 m HMI Cable 2 m serial remote keypad cable set. - - -
10951223 3 m HMI Cable 3 m serial remote keypad cable set. - - -
10951227 5 m HMI Cable 5 m serial remote keypad cable set. - - -
10951240 7.5 m HMI Cable 7.5 m serial remote keypad cable set. - - -
10951239 10 m HMI Cable 10 m serial remote keypad cable set. - - -
11010298 HMID-01 Blank cover for the HMI slot. HMI - -
Miscellaneous
11010787 KN1A-01 Conduit kit for frame A (standard for option N1).(5) - - -
11010800 KN1B-01 Conduit kit for frame B (standard for option N1). (5) - - -
Accessory models (Cont.)

CFW-11 | 9
- English -
Addendum to the CFW-11 User's Manual
WEG Part
Number Name Description Slot
Identification
Parameters
P0027 P0028
11010802 KN1C-01 Conduit kit for frame C (standard for option N1). (5) - - -
11010264 KIP21D-01 IP21 kit for frame D (standard for option 21). - - -
11010265 PCSA-01 Kit for power cables shielding - frame A (standard for
option FA).
- - -
11010266 PCSB-01 Kit for power cables shielding - frame B (standard for
option FA).
- - -
11010267 PCSC-01 Kit for power cables shielding - frame C (standard for
option FA).
- - -
11119781 PCSD-01 Kit for power cables shielding - frame D (included in the
standard product).
- - -
10960847 CCS-01 Kit for control cables shielding (included in the standard
product).
- - -
10960846 CONRA-01 Control rack (containing the CC11 control board). - - -
Notes:
(1) Refer to the PLC Module Manual.
(2) Refer to the Anybus-CC Communication Manual.
(3) Refer to the Software Manual.
(4) Use DB-9 pin, male-to-female, straight-through cable (serial mouse extension type) for connecting the keypad to
the inverter or Null-Modem standard cable. Maximum cable length: 10 m (33 ft).
Examples:
- Mouse extension cable - 1.80 m (6 ft); Manufacturer: Clone.
- Belkin pro series DB9 serial extension cable 5 m (17 ft); Manufacturer: Belkin.
- Cables Unlimited PCM195006 cable, 6 ft DB9 m/f; Manufacturer: Cables Unlimited.
(5) Refer to the section 8.4 - Conduit Kit, for more details.
3.2 HMI Installation at the Cabinet Door or Command Panel (Remote HMI)
113.0 [4.45]
65.0 [2.56]
28.5 [1.12]
23.5 [0.93] 35.0 [1.38]
16.0 [0.63]
∅4.0 [0.16] (3X)
23.4 [0.92]
103.0 [4.06]
Figure 3.1: Data for the HMI installation at the cabinet door or command panel – mm [in]
Accessory models (Cont.)

10 | CFW-11 - English -
Addendum to the CFW-11 User's Manual
The keypad frame accessory can also be used to fix the HMI, refer to the section
7.2 - Accessories, of the CFW-11 user's manual.
3.3 Additional Information about the HMI Battery
NOTE!
The battery is necessary only to keep the internal clock operation when the
inverter stays without power. If the battery is completely discharged or if it
is not installed in the keypad, the displayed clock time will be invalid and
an alarm condition “A181 - Invalid clock time” will be indicated whenever
the AC power is applied to the inverter.
The battery life expectancy is of approximately 10 years. When necessary, replace
the battery by another of the CR2032 type.
Cover for battery access Press the cover
and rotate it
counterclockwise
Cover
1 2 3
Remove the cover
Remove the battery with
the help of a screwdriver
positioned in the right side
HMI without the battery
4 5 6
Install the new battery
positioning it first at the
left side
Figure 3.2: HMI battery replacement