FWD/REV
OFFON
PROG DEF User Description
P0220 0 1 Local/Remote = always remote
P0222 2 1 Remote reference = Al1
P0226 2 4 FWD/REV = DIx
P0227 3 1 Start/Stop remote = DIx
P0231 0 0 AI1 = speed reference
P0233 0 0 AI1 = 0 - 10 V
P0263 1 1 DI1 = start/stop
P0264 8 8 DI2 = FWD/REV
Example 2: 3 - Wire Start/Stop, 4 - 20 mA Reference
4 - 20 mA
Reference
ON
CFW100-IORA
DIP SWITCH
Digital input 1
Product
DI 11
2
3
4
5
6
7
8
DI 2
DI 3
DI 4
GND
GND
AI 1
+ 10 V dc
Digital input 2
Digital input 3
Digital input 4
Reference 0 V
Reference 0 V
Analog input 1
Reference + 10 V potentiometer
CFW100-
IORA
(optional)
START
STOP
PROG DEF User Description
P0220 0 1 Local/Remote = always remote
P0222 2 1 Remote reference = Al1
P0227 3 1 Start/Stop remote = DIx
P0231 0 0 AI1 = speed reference
P0233 0 1 AI1 = 4 - 20 mA
P0263 1 6 DI1 = start
P0264 8 7 DI2 = stop
Example 3: 2 - Wire Start/Stop, Multispeed (4 Speeds)
Digital input 1
DI 11
2
3
4
5
DI 2
DI 3
DI 4
GND
Digital input 2
Digital input 3
Digital input 4
Reference 0 V
Product
START/STOP
SPEED
SPEED
OFFON
OFFON
PROG DEF User Description
P0220 0 1 Local/Remote = always remote
P0222 2 8 Remote reference = multispeed
P0227 3 1 Start/Stop remote = DIx
P0263 1 1 DI1 = start/stop
P0265 0 13 DI3 = multispeed
P0266 0 13 DI4 = multispeed
P0124 3 ▲Speed = ▲(DI3 = open and DI4 = open)
P0125 10 ▲Speed = ▲(DI3 = open and DI4 = closed)
P0126 20 ▲Speed = ▲(DI3 = closed and DI4 = open)
P0127 30 ▲Speed = ▲(DI3 = closed and DI4 = closed)
Note: ▲Speed setting depends on application.
Note: for more advance functions, please refer to the programming manual.
Relay Output PROG DEF User Description
P0275 13
11 Run
12 Ready
13 No fault
26 With fault
9 DO1-RL-C Common
Normal open
10 DO1-RL-NO
CFW100-
IORA
(optional)
Programming
Start-Up (Scalar - V/F Mode)
Note: set P0202 = 5 during oriented start-up for improved speed control and
higher torque capacity at low speed (especially <5 Hz).
■Set as per motor nameplate data.
PROG DEF User Description
P0202 0 0 Control type V/F
P0401 - ■Motor FLC (A)
P0402 1710 ■Motor speed (RPM)
P0403 60 ■Motor frequency
Run button:
- Run in local mode
Stop button:
- Stop in local mode
- Reset
Up/Down buttons:
- Adjust speed in local mode
- Navigate through parameters
Prog button:
- Use to Select/Save
PROG DEF User Description
P0156 1.2 x Inom 1.1 x Inom Overload current
Motor Overload Settings
PROG DEF User Description
P0100 5s ▲Acceleration time (s)
P0101 10s ▲Deceleration time (s)
P0133 3 Hz ▲Minimum speed (Hz)
P0134 66 Hz ▲Maximum speed (Hz)
Basic Application
Note: ▲Setting depends on application.
PROG DEF User Description
P0204 0 5Load factory defaults (60 Hz)
Loading Factory Default Setting
User Description
2 Output speed (Hz)
3 Motor current (A)
5 Output frequency (Hz)
7 Output voltage (V)
9 Motor torque (%)
Changing Monitor Display Parameter
Bar to monitor the variable. See parameters
207, 208 and 213 to adjust bar graph
Main display
Direction of rotation
Inverter status
Unit of measurement
(it refers to the value of
the main display)
Installation & Power Connections
Typical Control Connection
Refer to user guide chapter 3.
Remote Keypad
